Search Documents

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By Wallace W. Key

Problems of marketing industrial minerals to chemical manufacturers are manifold. In addition to the difficulty of establishing demarcation lines between "crude" and "processed" industrial (nonmetallic) minerals, and "industrial mineral compounds" further uncertainty exists because some chemical manufacturers do not talk the same language as the industrial mineral producer. For example, paint technologists use "rutile" and "anatase" to describe highly refined chemical compounds. The earth scientists use these terms to describe naturally occurring minerals. Further, marketing research problems are intensified because of the overlapping data of the Standard Industrial Classifications (SIC) groups, and the inexactness of "Chemical Industry," "Chemical and Allied Products Industries," and "Chemical Process Industries," which are widely variable in meaning but are often used interchangeably. Bureau of Mines information Circular 8244, "Minerals for Chemical Manufacturing," was the out¬growth of an attempt to unravel some of the problems caused by overlap of statistical data compared with actual industry practices. Using this study as a base, specific industrial mineral applications of some important sub-industry groups were analyzed for the; California chemical industry. Differences between local and national practices were compared. Practices usually differed, depending on cost and availability of alternate minerals, climate, idiosyncrasies, local regulations, and other conditions. Bureau of Mines Information Circular 8260, "Mineral Fillers for the California Pesticides Industry," is the first such analysis of, a sub-industry group. Other such studies are underway. Obtaining national data is easy, but to be able to compile meaningful information which can be revealed on a regional and State basis generally is difficult and often impossible. This paper will briefly emphasize some of the industrial mineral problems encountered, and bring out the needs and benefits being derived through the continued cooperation of authoritative officials concerned with supply and consumption of industrial minerals in government and industry.

Jan 1, 1965

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By I. Iwasaki

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron micro-probe, scanning electron microscope and scanning auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures which have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their implications to the flotation recovery of arsenide minerals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1985

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By George W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment® , two new lime substitutes for the treatment of acid mine drainage (Arm), have been compared with lime and Alkament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with EPA regulations. Material utilization and optimum pit are reported.

Jan 1, 1984

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater's can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977

By William A. Riggs

Salt, a non-metallic mineral whose use dates back to earliest history of mankind, and whose uses cover the widest range for any mineral raw material, is generally of widespread occurrence in commercially recoverable quantities in the oceans, in certain sedimentary rocks, in certain lakes, and in certain underground waters. Passing over geological detail, it may be said that, generally, all of the salt in the world has, at least once in geological history, been in solution in the oceans. The total salt content of today's oceans, said to equal 4.5 million cubic miles of rock salt, dwarfs the tremendous volume of salt in the sedimentary rocks. In 1958, United States production of salt was about 22 million net tons and world production about 82 million. About 3 percent of United States production is table salt, with chemical, municipal, industrial and agricultural uses taking the remainder. Mississippi River. Figure 1 has been expanded sufficiently to show also those salt occurrences and producing points which might economically ship salt into these states. Although widespread in occurrence, salt deposits and possible production areas generally show very sharp local boundaries. Salt-for non-table use is susceptible to ?place value?, a common problem in low valued raw materials, where transportation costs often exceed the value of the material f.o.b. the production point. Generally only large capacity mechanized salt producing operations can compete in United States markets, as contrasted to the many small local salt evaporators in less industrialized Mexico.

Jan 1, 1962

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By T. V. Falkie

REMARKS OF DR. THOMAS V. FALKIE, DIRECTOR, BUREAU OF MINES, U.S. DEPARTMENT OF THE INTERIOR, BEFORE THE FALL MEETING OF THE SOCIETY OF MINING ENGINEERS, AIME, ACAPULCO, MEXICO, SEPTEMBER 23, 1974 This is a time of uncertainty on the world mineral scene. For some of the world's so-called "developed" countries, reserves and production of key minerals are running low. And, we have learned that the energy so essential in recovering and processing minerals can suddenly be in short supply. The prospects for a "no growth" situation in energy or mineral consumption are practically nil. Moreover, the world's economy is in flux, casting doubt on whether traditional mineral customers will continue to be able to buy, or for that matter, whether traditional suppliers of minerals will continue to sell. It is clear that the mineral situation is contributing to world inflationary pressures, which incidentally are most damaging to developing countries. So it is appropriate that SME members devote this session to the world mineral situation, and consider some of the opportunities and responsibilities that we will inevitably encounter as the future becomes the present. The opportunities, to me at least, are especially intriguing, I have the good fortune to be part of an organization that has an enormous capability and responsibility for dealing with mineral problems. The Interior Department's Bureaus, including the Bureau of Mines, have been around for a long time. They are. a prolific and reliable source of both mineral information and mineral technology.

Jan 1, 1974