Search Documents

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By L. B. Gittinger

Mr, Chairman, members- and guests of the AIMS, I greatly appreciate this opportunity to speak before you. I hope this is just the beginning of a long and mutually beneficial relationship. This winter I decided to join the other 36 Freeporters who belong to the AIME; and, I applied for membership in the Society of Mining Engineers. To queries as to my interests in the Society, I had this answer: our principal challenge -- more so today, than at any time in my nearly 25 years in the industry -- is discovery and development of new sources of raw materials. I want to join you in meeting this challenge.

Jan 1, 1966

By M. Peters, P. Schmäh

The development of renewable energies and a sustainable power grid are the challenges for future energy supply. Underground cables will replace the vulnerable overhead lines, because of their safety benefits. Due to the public environmental awareness, smart tunnelling and trenchless solutions are required for inner-city and cross-country installations of underground cables, as well as for crossings and the landfall sections to connect offshore wind farms to the transmission grid. Methods from the tunnelling and pipeline industry provide a high flexibility in the planning of alignments, including versatile tunnel concepts and the installation of protective pipes with E-Power Pipe and Direct Pipe.

Jun 13, 2023

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

Sequential and evolutionary changes through time are recognizable in many, perhaps most major families of ore deposits and their geological environments. These changes are additional useful indicators of the evolutionary history of the earth and its tectonic processes. They are important in mineral exploration because they involve consideration of time as a fourth dimension, thereby indicating the most favorable ages, rather than types of rock for investigation. Many of the changes are analogous to those recognized in faunal evolution. Some primitive, unspecialized types of ore deposits occur nearly unchanged through rocks of widely differing age. Others diversify into several, more specialized variants, whereas still others become extinct. The place of these is taken by new, younger types, some of which undergo sudden proliferations and later diversifications of their own. In Archean greenstone belts irrlportant iron, nickel, gold, and base metal deposits occur co-regionally, but in different stratigraphic positions in the same, thick volcano-sedimentary successions. Here their close temporal and spatial associations suggest common genetic exhalative hydrothermal processes. The massive base metal sulfide family of ore deposits provides an excellent example of evolutionary changes, exhibiting distinct variations through both time and space. Deposits belonging to this family span the entire range of time, occurring in rocks of ancient Archean to Recent age, and specific types within the family also span the entire range of spatial environments from ensimatic to ensialic. Moreover there are possible evolutionary metallogenic links between certain types of massive base metal sulfide deposits and other important base metal ores, noteably Mississippi Valley-type and porphyry copper deposits.

Jan 1, 2013

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025