Search Documents

By Zdenek Kunicky

Kovohute Pribram is a plant recycling lead wastes, lead acid batteries in particular. Relevant new recycling technologies are being gradually developed. Outdated technology of smelting lead plates has been replaced by a new technology based on processing of entire batteries in a blast furnace according to the process developed by know-how of German Varta company. The classical Harris refining has been substituted by the oxygen refining. New technologies aimed at utilization of related wastes arising from refining lead bullion in Kovohute Pribram are being developed in house. At present, a new technology of utilization of spent battery acid for extracting zinc from various wastes has been developed. Zinc oxide dross from alkaline refining of lead bullion, during which residual zinc from the preceding vacuum de-zincing is removed as well as waste zinc galvanic sludges (a product of neutralizing precipitation of metals from industrial wastewaters with lime) were treated. In this study, the new developed technology yielding basic zinc carbonate - a valuable raw material for zinc electrowinning, is described together with the first experience of applying the developed method to processing zinc wastes on a pilot scale. Most of the equipment used in the past to regenerate alkali solutions originating from Harris refinery was utilized in the practical realization of this new technology.

Jan 1, 2008

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By T. Steyn, M. Fofana

"One of the most important performance indicators of a dense medium cyclone (DMC) circuit is the Tromp curve, and by extension the separation density and Ecart Probable (Ep) values. The densimetric profiles of DMC product streams have been traditionally acquired using heavy liquid sinkfloat analysis, which has certain disadvantages, such as the associated safety and health risks. More recently, non-toxic media such as lithium hetero-polytungstates (LST) have been used, with the desired densities being achieved by maintaining the solutions at specific temperatures. However, the high costs of these liquids can be prohibitive. The long turnaround time of the sink-float analysis is a further disadvantage for timeous interventions to the operating set-points of the DMC process.The RhoVol technology can generate the density distribution of a batch of particles in a rapid, accurate, repeatable, and safe manner. Additional data of interest, such as particle size and shape, are also measured and reported on a per-particle basis. Furthermore, samples can be sorted into discrete sorting bins based on any of the measured parameters of the particle, making further analyses of the material possible.This technology has applications across all commodities that use the DMC, particularly in the size fractions –25 +8 mm and –8 +3 mm. To date, laboratory results have proved very encouraging – separation densities are within 5% of traditional sink-float results, and the technology is being introduced to diamond DMC plants. IntroductionDense medium separation is a commonly applied beneficiation technique for the density separation of valuable products from crushed ores. The industrial applications of dense medium separation have been summarized and reviewed by various authors (Scott and Napier-Munn, 2000; Bosman, 2014; Napier- Munn, 2018). Dense medium cyclones (DMCs) are widely used in the coal and diamond industries to produce clean coal or to preconcentrate kimberlitic ores, respectively. Cyclone performance (separation density monitoring) techniques are varied. In the mineral industry. Density tracer tests (Napier- Munn, 1985, 2014; Davis, Wood, and Lyman, 1985) without mineral material, are widely used, although their accuracy in predicting operating cut-points becomes limited once mineral material is introduced. More recently, radio frequency tracers have been also used for the determination of cyclone efficiency (Partition Enterprises, 2017)."

Feb 1, 2019

By G. Akdogan, T. P. Kekana, Q. G. Reynolds

The DC arc plasma gasifier concept is currently under development at Mintek for testing the feasibility of producing syngas from waste coal fines and dry steam. The technology is intended for the valorisation of low-grade discard coals into market-quality syngas, which may then be used for largescale electrical power generation to address current grid supply challenges in South Africa. Other potential applications include feedstock for petro-chemical plants, fuel for transportation vehicles, domestic and industrial heating, and others. The proposed concept of a DC arc plasma gasifier was developed based on a plasma torch, metallurgical-based and entrained flow coal gasifiers. The principles of design and operation of the proposed gasifier are based on the concept of the Westinghouse Plasma Corporation (WPC) gasifier where the torches are substituted by graphite electrodes from which electric arc plasmas are generated. The DC section of the gasifier will be designed considering Mintek’s experience in the sealing of the furnace as carried out in the Mintek Thermal Magnesium Process. As part of the building blocks of a full conceptual design, the feasibility of the DC arc plasma gasifier was investigated through testing and modelling of its critical elements as proof of concept. The main activities of this work included pilot scale evaluation of the arc behaviour in the presence of dry steam, modelling of the temperature distribution within the reactor and explosibility studies on three different coal dust samples. Keywords: DC arc plasma gasifier, explosibility index, lower explosion limit, minimum ignition energy

Jan 1, 2020

By Y. Fan, D. H. Zhang, J. Y. Xu

The hydrogeological conditions in the Chambishi mine area in Zambia. were investigated. Chambishi is a very wet mine and groundwater discharge costs are high. The research goal was to identify methods to reduce the discharge costs without greatly affecting the mining process. Hydrogeological data was obtained from measurements in drill-holes and from drill cores. The differences in structural deformation in different areas determine whether a layer of rock is an aquifer. In the mine region, the Lower Roan Group ore shale and quartz-sandstone unconformably lie on the basal schist and granite aquifuge. The Upper Roan Group dolomite is continuously distributed over a large area around the orebody. This dolomite is the main target of groundwater control efforts, and its water yield is also influenced by the deformation intensity. Based on the observations, backfilling was gradually adopted to appropriately safeguard the integrity of the aquifuge above the orebody. The overlapping relationship between the aquifer and aquifuge has been utilized to increase mine drainage efficiency. This measure has not only greatly reduced the costs of mine drainage, but also improced protection of the groundwater environment. The old drill-holes that were not sealed after exploration drilling were grouted. Further, possible water-conducting fracture zones were investigated. Cover drilling towards the suspected zone was conducted to prevent the high-pressure groundwater from shallower aquifers from entering stopes in deep areas of the mine.

Jun 10, 2024

By G. R. Addie

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains a new method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By D. F. Malan, W. J. Theron

Practical mining aspects should be considered when conducting pillar designs for bord-and-pillar layouts. The current methodology for pillar design will result in increasing pillar sizes with depth. This affects the extraction ratio and will result in onerous ventilation requirements when cutting large pillars. A holistic approach, including all mining engineering requirements, is required to ensure that the rock engineering designs are optimized to ensure efficient mining operations and sustainable production. Bord widths should not only be a function of the rock mass ratings, but should also be selected to fit the specifications of the mechanized equipment. The use of a ‘squat pillar’ formula for hard rock is discussed in the paper and the formula based on the exponents of the Hedley and Grant pillar formula, is explored. The effect of abutments and geological losses on average pillar stress is also explored. These factors must be considered when designing layouts at increasing depths.

Nov 27, 2024

By G. J. C. Young

The new metallurgical plant has a simple, compact layout, being designed for a small team of operators. The reasons for building the new plant are given, and its various sections are briefly described. These include the conveyor plant, milling plant (for run-of-mine milling), thickener plant, agitator plant, filtration, clarification, smelthouse, and central core joining the mill and filtration sections.

Jan 1, 1978

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By M. H. Moys, J. Engelbrecht, N. Terblanche

Interface levels in flotation columns are generally measured with the aid of a pressure-sensitive Instrument, e.g. a differential-pressure cell. This paper criticizes the use of this type of measurement, and discusses other methods that are claimed to give more accurate measures of interface levels. The paper focuses on the development of methods based on the measurement of conductivity across the froth-slurry interface. These are often sabotaged by variations in the conductivity of the feed slurry, particularly when the pH of the slurry IS being controlled, e.g. In sulphide flotation. Methods of improving the accuracy and reliability of this technique are described. The result IS a robust, easy-to maintain level-control scheme that successfully rejects large disturbances in plant operation (including a 5:1 change in slurry conductivity) while controlling levels to an accuracy of I 4 cm.

Jan 1, 1992

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By H. J. R. Way

Dr H. J. R. Way: In his reply to my queries Mr Bath still adheres to his statement that it may be possible to replace the estimated R200 million reduction in gold revenue in 1980 by exports of ferro-chromium, and apparently based his conclusion on a growth rate in demand for corrosion resistant steels of 10 per cent per annum in the next few years. As I pointed out at the previous discussion at Middelburg this would entail a production of about one million tons of ferro-chromium in 1980. Exact statistics of South African ferro-chromium production are not available, a fact which is very much to be regretted. But statistics of exports of ferro-chromium are available from "Foreign Trade Statistics" of the Customs and Excise. These show that South Africa exported 99,580 short tons in 1967. The quantity of ferro-chromium consumed in South Africa in 1967 was fairly small and we can therefore assume that the production was 99,580 tons. For this amount to grow to 1,000,000 tons in 1980 would require a growth rate of 19.4 per cent per annum. At 10 per cent this would grow to 344,000 tons and at 7 per cent 240,000 tons. The following growth rates in the form of average trends are pertinent: STEEL - Per annum World steel ingot production - 1957-67 – 6.8 per cent Free-world ingot production - 1957-67 – 6.0 per cent Consumptions of crude steel by four major Free-world Consumers - 1957-67 - 5.6 per cent CHROMITE World production - 1952-67 - 2.5 per cent South African total sales - 1948-67 – 5.4 per cent South African exports - 1948-67 – 3.9 per cent United States consumption, very irregular, but - 1962-67 – 6.5 per cent FERRO-CHROMIUM - Per annum United States consumption - 1952-67 - 6.5 per cent South African exports - 1957-62 - 25.2 per cent South African exports - 1962-66 - 41.9 per cent South African exports - 1966-68 - 21.2 per cent These figures show that exports of ferro-chromium have been growing at a very high rate varying from 21.2 per cent to 41.9 per cent since 1957, but in view of the market situation it seems somewhat doubtful if that high rate can be maintained up to 1980. Of our 1966 exports U.S.A. took 63 per cent which was 53 per cent of their total imports. Their average consumption is trending at a growth rate of 6.5 per cent per annum from 1952-67, but the growth from 1964-66 was 5- 2 per cent and 1966-67, -12 per cent!

Mar 1, 1968

By C. W. Siyasiya

Process and steel chemistry differences in hot rolled Al-killed low carbon strip steel between the hot charge route (HCR) as practised in a compact strip production (CSP) plant and the conventional cold charge route (CCR) have been studied. This was done with reference to differences in reheating practice, hot rolling practice and steel chemistry through emphasis on the effects of solubility and reprecipitation of AlN in the two process/product combinations and its effect on ferrite grain size development. An earlier modelling study on the evolution of the austenite grain size in both of the above hot rolling processes has also now been extended to include an estimate of the possible effects of retained strain after the last finishing pass on the ferrite grain size. As part of this study the equilibrium solubility trends of AlN in a number of boron-free low carbon Al-killed strip steels with low and high sulphur content from the two respective processes was investigated by the thermoelectric power (TEP) technique and differences in the effects through the derived solubility equation of Log[Al][N]=2.6?9710/T at typical slab reheating temperatures was demonstrated. Ferrite grain size modelling using the significantly lower Ar3 transformation temperatures generally found in hot rolled low carbon strip steel produced in the CSP plant using the HCR compared well to the larger grain size produced in the conventional CCR strip rolling plant. Keywords: austenite grain size modelling; thermoelectric power(TEP); compact strip production (CSP); cold charge route (CCR);ferrite grain size

Jan 1, 2008

By B. Geelhoed

A generalization of Gy?s 1979 model for the variance of the fundamental sampling error has been proposed at WCSB2?2005 by Geelhoed. This generalized model can potentially lead to a better correspondence with actual sampling processes. However, a new parameter is required by the new model: ?the parameter for the dependent selection of particles?(Cij). It is important that this new parameter, which is at the basis of the new theory, is well understood in the sampling and blending community. In order to clarify the meaning of Cijand to prevent potential misinterpretation of Cij, we discuss the difference between Cij and an intuitively associated, but different, parameter: ?the parameter for the dependent selection of particle types?(Mij). In this contribution, the theoretical difference between both parameters is clarified. Simulations demonstrate that, numerically, the difference between Cij and Mij can be large. Some additional advantages of the approach which uses Cij are discussed: (i) the approach based on Cijis more general; (ii) in all cases where Mij is known, Cij can be determined as well, while the reverse is not true; (iii) an equation already exists that relates the sample variance to the value of Cij.

Jan 1, 2009

The President: "It gives me great pleasure to call on Professor Howat to present the paper written jointly with P. R. Jochens and C. W. Wolhuter entitled, 'Utilisation of slags for the manufacture of cement.' After the presentation of the paper the President said: "Thank you, Professor Howat, for so ably introducing the paper prepared by yourself, Dr Jochens and Mr Wolhuter. Once again we are deeply indebted to you for bringing to our attention a new development in the metallurgical field, this time a technique for assessing the suitability of slags for the production of slag cement, and thereby providing a means of turning a waste material into a valuable asset. May we hope that this will lead to an end to unsightly slag dumps and, at the same time, to some conservation of our local limestone resources. Discussion within this Institute on the problems of cement manufacture, has of recent years been all too infrequent, and we thank you for bringing this interesting and important subject again to our notice. We are doubly grateful to you and your co-authors. May I now call on Dr Stutterheim, Deputy Director of the Council for Scientific and Industrial Research, to contribute to your paper, and to tell us something about the Conference on the Chemistry of Cement which he attended in Tokyo towards the end of last year." (Applause.) Dr N. Stutterheim, Mr B. F. van der Merwe and Dr F. S. Fulton then contributed to the paper. (These contributions will appear in a later issue of the Journal.) PAPERS OPEN FOR DISCUSSION The President: "Listed on the agenda are papers open for discussion. I would suggest that anyone wishing to contribute to these papars, submit their contributions to the Secretary in writing." CONCLUSION The President: "I would like to thank everybody for their attendance here tonight, and on your behalf I am sure you would like me to thank the authors and the contributors for the most interesting time that we have had this evening. Thank you very much." The meeting closed at 6.00 p.m. NOTICE SYMPOSIUM ON THE RECOVERY OF PYRITE A symposium on the recovery of pyrite will be held on 12th and 13th June, 1969 at Kelvin House, Johannesburg under the auspices of the Institute and the National Institute for Metallurgy. Notices will be sent to members as soon as more details are available as regards the papers and the programme.