Search Documents

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By C G. Robinson, B. K. Loveday, J. C. Paynter

"A method of optimizing the design of a processing plant has been developed which minimizes capital and operating costs for average stripping ratios and ore characteristics. Models were developed to describe the operating characteristics and costs involved in various operations such as up-grading, leaching and solid-liquid separation.The options available in up-grading policy and the relation between the cut-off grade and the costs incurred subsequently in the treatment of the ore formed the basis of the optimization. To arrive at an optimum plant configuration and a set of operating parameters, the interrelation between grinding size, leaching temperature, leaching time, and various plant recycle options was investigated."

Jan 1, 2014

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By B. Amankwaa-Kyeremeh, W. Skinner, R. K. Asamoah, C. Greet

With the continuous increase in ore mineralogical complexity coupled with decreasing head grades, there is a need for mining industries to process large tonnages of material to meet global metal demands. Smarter, cheaper techniques are required to better map ore mineralogical variations proceeding to pre-concentration (flotation) stages for higher performance and metal recoveries. This paper is aimed at briefly reviewing previous studies on different selected ore mineralogy, with the focus on their pulp chemistry, to identify relationships which aid quicker flotation feed variation monitoring. Very little published work exists linking pulp chemistry parameters to flotation feed mineralogical variation. A successful application implies maximising grades at higher metal recoveries and reducing the cost of reagent for a better performing flotation circuit. Keywords: Mineralogical variation, flotation, pulp chemistry

Jan 1, 2020

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By Maggi Loubser

"In a technologically advanced era, where process control is accurately maintained within the smallest error margins, and accuracy and precision are continuously improved, sampling is still left to the lowest paid employee in the company without training him or her properly to understand the relevance and importance of the task. In this paper the objectives of sampling in a process control environment is discussed and an attempt is made to link it to the theory of sampling. Some of the practical problems associated with implementing theoretical sampling principles in an industrial environment will be elucidated and some examples given on how compromises are made. Different methods of sampling will be discussed with real life examples from different manufacturing industries."

Jan 1, 2014

By F. D. Agrensa, J. Hadjigeorgiou, E. Storimans, S. J. Thorpe

Reinforcement and surface support are part of an integrated system that transfers and shares loaduntil the excavation surface is stabilized or until the ground support system fails. Steel mesh is the most popular primary surface support element in underground hard rock mines in Canada. Mesh straps are a secondary surface support that provide additional containment as they distribute the load between and across the reinforcement elements. This investigation addresses the role of steel properties, and in particular steel chemistry, in the long-term performance of mesh and mesh straps when exposed to an aggressive corrosive environment. It reports on comparative accelerated corrosion studies to compare the resistance to corrosion of different surface support elements. This has significant implications on the choice of surface support and the anticipated rehabilitation requirements.

Oct 9, 2024

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By K. Wu, X. Yuan, R. Du, C. Chao

"Lump coals are currently employed to replace part of coke in the COREX melter-gasifier for ironmaking. In order to optimize the process, the pyrolysis kinetics of Datong coal used in the COREX process was studied. A sectioning method is proposed to overcome certain shortcomings of traditional methods for studying the pyrolysis of coal. Based on the sectioning method and the characteristics of the coal pyrolysis process, the temperature range was divided into three intervals. In the first, the adsorbed gas and water of crystallization were removed; in the second, the coal was transformed into semi-coke; and finally, the semi-coke was further coked. Three models of reaction were then established to study the different stages of the pyrolysis process: an interfacial chemical reaction model, a random pore model, and internal diffusion with shrinking volume. The results showed that the experimental data fitted the models well, with all correlation coefficients (r2) exceeding 0.97. Finally, the mechanisms of reaction and kinetic parameters for each temperature range were derived, which laid a necessary foundation for optimizing the usage of non-coking coal in the COREX process. IntroductionIn view of environmental concerns and the shortage of good-quality coking coal, the COREX process was designed as a new ironmaking technology, attracting wide attention (Fang et al., 2005). In this process, lump coal and a small quantity of coke are directly charged into the melter-gasifier, where a high-quality reducing gas is generated for the reduction of the iron ore (Kumar et al., 2009). In contrast to the conventional blast furnace (BF) process, non-coking lump coal is used as the reducing agent and as the energy source, and the iron charge consists of lump ore and/or pellets, which results in the elimination of the coke oven and sintering plant as well as a decrease in investment (Kumar et al., 2009; Liu et al., 2012).Although the COREX process has made great progress, in current production practice the energy consumption greatly exceeds that of the BF, and it requires a certain amount of coke to maintain permeability of the semi-coke bed (Wang et al., 2008). In addition, the process consumes a lot of good-quality lump ore and lump coal. The pyrolysis of coal is the first step in most coal conversion processes, such as carbonization, gasification, and combustion (Aboyade et al., 2013). The reaction behaviour of lump coals in the COREX melter-gasifier is crucial, as it determines energy utilization and gas composition, as well as the metallurgical properties and particle size of the semi-coke produced (Prachethan et al., 2011; Zhang et al., 2014). In order to optimize the process and improve its competitiveness, the pyrolysis kinetics of Datong coal used in Baosteel’s COREX C-3000 facility was studied."

Jan 1, 2016

By B. M. V. Baloyi, D. Mchabe, D. Chetty

South Africa accounts for the largest global manganese ore production share, primarily from its Kalahari Manganese Field deposit. Despite this, domestic smelting is beset by energy constraints, resulting in most ore being exported for smelting. Mintek is investigating energyefficient pathways for ore reduction, specifically undertaking prereduction tests to reduce energy consumption for manganese smelting. The present contribution considers the effect of methane, anthracite, and holding time, at a fixed temperature, on the extent of reduction of Mamatwan-type ore, primarily from a mineralogical perspective. In particular, the aim was to carburise the monoxide Mn phase to Mn carbide, as this is less energy intensive than producing metallic Mn from the monoxide. Based on thermogravimetric test results, the ore and products from three experiment sets were analysed using X-ray diffraction and scanning electron microscopy to assess the phases and textures present. The findings show that carburisation of manganese monoxide and its equivalents is most advanced under conditions of 8% anthracite, 10% methane, and 60 minutes of holding time, thus confirming with the thermogravimetric data. These results show promise for reducing energy consumption for Mn smelting in ferromanganese production.

Mar 4, 2025

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020

By J. M. Stewart

The purpose of my few comments is to try to create a healthy perspective to constructively link considerations of the sessions to follow to those of the earlier sessions. I propose to do this by considering some of the issues and priorities related to the development of backfill systems and technology for South African gold mines.

Jan 1, 1988

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015