Search Documents

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

By T. Käyhköa, J. Liipoa, S. Khizanishvilic, M. Sinche-Gonzalezb

The use of geometallurgical modelling is becoming more common in concentrator plant design and during the operational phase. Predictive modelling aims to define optimised process parameters for the concentrator plant to accommodate variability within the ore feed. The main objective of this study is to show how the metallurgical response of different types of ore blends can be simulated using kinetic models derived from experimental flotation tests with different geometallurgical end-member ore types and their blends. For these validation tests, four different end-member ore types containing different ratios of chalcopyrite, chalcocite and oxidised copper minerals from Rich Metal Group’s Madneuli copper-gold mine, Georgia, were tested. Kinetic flotation tests, including both rougher and cleaner flotation tests, were carried out. The simulations were performed using HSC Chemistry software based on mineral compositions of the ores and kinetic models using rectangular distribution equations and flowsheet model. Simulated and experimental results of copper grade, copper recovery and concentrate mass pull correlated well with R2 values of >0.95. Based on these results, the metallurgical response of different ore blends can be simulated based on the flotation kinetics of end-member ore types. The use of this kind of simulation will create savings during the test work phase and increase the flexibility and predictability in the processing stage. Keywords: Ore body characterisation, geometallurgy, process mineralogy

Jan 1, 2020

By M. S. Shishvan, S. Klerkx, J. Sattarvand

The inaccurately drilled blastholes from the planned locations cause changes in the spatial distribution of explosive energy; some areas of the blast may receive a surplus of explosive energy, while others see a reduction. This results in less uniform fragmentation, reduces the efficiency of mining operations and increases costs. Additionally, it can lead to slope stability issues, flyrock, and uneven benches. To mitigate these problems, this study attempts to reduce differences in the explosive energy distribution (EED) through an optimization approach that adjusts the height of explosive columns in blastholes. Two optimization algorithms, the Genetic Algorithm (GA) and Tabu Search (TS), are tested. The latter is preferred for its local search neighbourhood strategy that gives superior computation times. Applications on different blast patterns result in improvements of 0.53–1.54%, or 2.14–3.94% when only the affected blocks are considered.

Sep 1, 2021

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By F. Mwaura

"The aim of the audit was to determine whether the mining project environmental impact assessments (EIAs) in Kenya are undertaken according to international best practice. A sample of 50 EIA reports for the 2007–2016 period was evaluated using 18 criteria in the Environmental Law Alliance Worldwide (ELAW) guidelines. The findings showed that only two criteria were considered ‘excellent’ according to the ELAW guidelines, namely baseline environmental assessment and prediction of physical impacts. Six criteria were found to be ‘satisfactory’, including prediction of social impacts, analysis of alternative options, and impact mitigation. The reports were quite weak in terms of: consideration of all phases in the mining cycle, environmental regulatory framework, prediction of biological impacts, stakeholder consultation and engagement, integration of human right issues, and integration of climate change and cost-benefit analysis. It is therefore recommended that the Kenyan National Environment Management Authority (NEMA) should consider tightening the EIA terms and conditions in the approval of statutory terms of reference (ToR) for full-scale mining EIAs to ensure improved performance of EIA as a tool for environmental protection. IntroductionThe nexus between society and the environment has continued to generate interest because the environment is the source of goods and services that sustain the various needs of human beings as outlined in the UN sustainable development goals (SDGs) (Armstrong and Peart, 2000; Sutton 2004; Chakrabarti 2007; Strange and Bayley 2008). All the five generic categories of societal needs, namely physiological needs (food, water, clothing, medicines, etc.), residential and occupational needs (shelter, transport, energy, etc.), economic needs (tradeable goods and services), leisure and recreational needs (tourism), and cultural and spiritual needs (e.g. sacred resources and ecosystems) (Mwaura et al. 2016) are addressed by the environment. Consequently, a wide range of development sectors have been established around the world in order to address the above needs (Lederer, Galtung, and Antal, 1980; Rammelsberg et al., 2006; Noonan, 2014). All these development sectors rely entirely on the environment for their proper functioning, as shown in Table I."

May 1, 2019

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

A Special General Meeting, followed by the February General Meeting of the Institute, was held in Kelvin House, Johannesburg, on 18th February, 1970, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 24 Members: Messrs A. R. C. Fowler, R. C. J. Goode, Prof D. D. Howat, Messrs D. G. Maxwell, J. A. Nixon, P. W. J. van Rensburg (Council Members), C. A. Border, J. C. Fritz, E. K. Gibson, P. L. Grimbeek, S. D. Hill, D. A. Immelman, P. J. Uoyd, M. Mrost, C. S. Macphail, D. G. Malan, W. D. Ortlepp, R. S. Pearson, A. J. H. Pole, Dr W. S. Rapson, L. W. P. van den Bosch, R. A. von Maltitz and Dr A. Whillier. Eight Associate Members: Dr M. I. Brittan, Messrs J. Brett, I. E. Clarke, C. L. de Jongh, W. B. Evans, D. Loubser, R. C. More O'Ferrall and G. R. Still. One Graduate: Mr T. J. Kotze. One Student: Mr J. A. Cruise. Nine Visitors: including Dr N. G. W. Cook, Messrs M. D. Labuschagne, A. Nicoll, S. Sadowski, Dr A. M. Starfield and Dr H. Wagner. Secretary: Mr D. C. Visser. Total present: 45. SPECIAL GENERAL MEETING The President: "You will have received notices of the Special General Meeting and I declare it duly constituted. In keeping with the trend of overseas and local institutes, your Council recommends that we should change our membership classification as indicated in the notes of the meeting. The new grades are proposed to replace those presently in the Constitution and By-Laws. In terms of Clause 4.8 of the Constitution a special general meeting must be held for the purpose of considering and, if approved, adopting with or without amendments, the revision of the undermentioned clauses of the Constitution, which Council now recommends should read as follows. Clause 2.2 'Corporate Members shall comprise the grades of Honorary Life Fellow, Fellow and Member', these being the equivalent of Honorary Life Member, Member and Associate Member. Clause 2.6. 'Non-Corporate Member shall comprise the grade of Honorary Fellow, Graduate, Associate and Student.' Are there any questions in regard to this proposal? If not would someone propose that these clauses be amended and adopted?" Proposer: Mr A. J. Nixon. Seconder: Prof D. D. Howat. The motion was then adopted. The President: "It is recommended that Clause 2.15 should read, 'A Corporate of the Member of the Institute shall be entitled to use the following authorised letters designating the grade of Membership in Honorary Life Fellow and Fellow, F.S.A.I.M.M. and Member, M.S.A.I.M.M.' Previously we used the letters M.S.A.Inst.M.M. and your Council considered that we should adopt the simpler lettering. Could I ask someone to propose that this amendment be adopted?" Proposer: Mr R. C. J. Goode.

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013