Search Documents

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By Nicholas Matthews, Vilem Petr

This project will report findings on the establishment of a new surface test site at the Colorado School of Mines Edgar Mine. Concerns over the blast effects on site neighbors prompted the study to be conducted. The current maximum charge weight of 20-lb was studied to ensure that all environmental effects were within the range prescribed by state and federal regulations. Geophone locations were surveyed using GPS and monitored using Instantel Minimate Plus instruments. Distances and orientation of measurement sites to the test site were varied according to the local geography and geology. Weather conditions were also observed and recorded during all tests. Neighbor complaints were recorded and taken into account during analysis. Current results show that the current charge limit results in a safety factor of over 200 for all blasting activities at the site. Data collection is ongoing and a review is to be conducted annually. These results will be presented in the future. Results are presented and discussed in the following paper. Copyright

Jan 1, 2010

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control

Feb 1, 2020

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Park Yun-Seok, Jung Seung-Won, Hwang Nam-Sun, Song Jin-hyuk, Kim Young-ho

This study proposes a new blasting vibration estimation formula that reflects the vibration reduction characteristics of electronic detonators, which are not considered in the current MOLIT blasting vibration estimation formula. Test blasts were conducted across six types of Korean open-pit blasting designs. The results of the test blasts showed that the K value for electronic detonators decreased by approximately 30% compared to electric detonators. Predicted Peak Particle Velocity (PPV) analysis indicated a reduction effect ranging from 30% to 31% across various types. By incorporating this reduction in the K value into the MOLIT blasting vibration estimation formula (K=200), a new electronic detonator blasting vibration estimation formula (K=140) was proposed. Using this new formula, the blasting damage range (R) was calculated under various vibration limits to evaluate constructability improvement. On average, the R value for electronic detonators decreased by about 17%, with significant reductions of around 41% observed for TYPE I under certain vibration limits. In conclusion, the adoption of electronic detonators in open-pit blasting operations improves blasting efficiency, reduces economic costs, and significantly enhances constructability. Electronic detonators have demonstrated superior performance in minimizing damage to safety facilities compared to traditional electric detonators, thereby proving their practicality and effectiveness in blasting operations.

Jan 21, 2025

Blasting in a development heading or breasting operations starts from a cut. The void created by the cut provides a free face for the remainder of the round. It is the most critical part of the round because the later firing charges cannot pull to the desired depth unless the cut comes out as planned. The Burn cut is most commonly used in Canadian mines.

Jan 1, 1995

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By John Vynne, John Hutchings

There have been a number of recent technological advances in instrumentation for blasthole drills, and more specifically in drill monitoring and HPGPS guidance systems. Likewise, great strides have been made in the development of drill and blast software systems which are user friendly, while providing far greater capability to accurately design and monitor drill and blast patterns.

Jan 1, 2011

By M. Szumny, P. Mertuszka, K. Fuławka

Multi-face destress blasting is the basic method of reducing rock bursts hazard in Polish copper mines. Blasting operations of this type are carried out regularly, twice a day in order to minimize the geomechanical threat while maintaining high extraction efficiency. Unfortunately, the assessment of the effectiveness of this type of work until recently was based solely on determining whether a given destress blasting triggered a seismic tremor or not. Information on the characteristics of seismic waves generated by blasting has so far been omitted in analyzes of this type. The lack of reliable knowledge about the generated seismic effect makes the introduction of constructive corrective actions impossible, which in turn significantly reduces the triggering potential of conducted destress blasting. This study presents the results of comprehensive work aimed at increasing the effectiveness of active rock burst prevention in Lubin underground copper mine. For this purpose, an innovative system for continuous monitoring of seismic waves induced by multi-face blasting was developed, and a new method for seismic assessment of the effectiveness of the destress activities was developed. Based on the monitoring data and the comprehensive analysis of waveforms, the effectiveness of individual blasting operations was determined, and on this basis, modifications to the drilling and blasting patterns aimed at increasing the generated seismic effect were proposed. The use of innovative methods of monitoring and data analysis made it possible to increase the effectiveness of the conducted activities, in terms of the magnitude of seismic vibrations, up to 250%. It should be emphasized that the introduced modifications were aimed at increasing the effectiveness of blasting operations while maintaining the current level of costs. As a result, the proposed solution turned out to be highly effective, significantly affecting the safety of the work carried out in Polish copper mines. Thus the proposed approach is planned to be implemented in other Polish copper mines belonging to KGHM in the near future

Jan 1, 2024

By Maja Franjic, Ian Tolliday, Chris Collins, James Wiltshire

Ammonium Nitrate Emulsions (ANE) are a large segment of the explosives market for the mining industry. These emulsions are generally designed to be very stable but when breakdown does occur, removal of the resulting thick, crystallized material can be difficult, hazardous, time consuming and costly. A heavily crystallized emulsion cannot be pumped, so manual removal often becomes necessary. Buildup of semi-solid layers of crystallized emulsion can occur in bulk storage tanks or in truck compartments. In these situations, a manual cleanup involving hazardous confined-space entry and a significant amount of downtime is usually required. Once the crystallized emulsion is removed from the equipment, there is very expensive disposal of the resultant waste via a licensed trade-waste company. A much more desirable solution for dealing with waste emulsion is to completely break the emulsion, allowing the oxidizer and fuel phases to separate into two distinct layers. These layers would then be readily pumpable and could be disposed of much more economically. It may even be possible that the separated oxidizer phase could be repurposed as fertilizer and the fuel phase could be used to manufacture granular ANFO explosives. There are some existing products on the market for breaking emulsion explosives, but these generally need a high degree of mixing into the emulsion to achieve adequate breakdown. The aim of this study was to identify surfactants systems (demulsifiers) capable of effectively breaking a range of waste emulsions with minimized agitation. This paper describes the development and performance testing of novel demulsifier products. The test work involved a comprehensive series of laboratory screening tests, where the demulsifier formulations were optimized. A highly efficient formulation was identified, and field trials were conducted on real world, full-scale waste emulsions. Results will be presented that demonstrate a viable solution for the disposal, and potential re-use, of waste ANE in the explosives industry.

Jan 21, 2025

By Scott E. Winston, Spencer C. Watson

Dynamite is a generic term for a variety of high explosive formulations containing a blend of liquid and solid nitrate esters co-mixed with solid oxidizers and carbonaceous fuels. Dynamites can be divided into general classes of nongelatins, semi-gelatins, and gelatins which vary as to their detonation rates, densities, and water resistance. There are also numerous products within each classification depending on their utilization or on their permissibility in various types of underground mining operations.

Jan 1, 1985

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By John R. Schuring, Walter Konon

The 2.0 in./sec. peak particle velocity criterion traditionally used to protect structures from blast induced vibration damage is non-conservative for landmark structures. Various factors which must be considered in establishing vibration criteria for landmark structures are discussed. Existing criteria by past investigators for this class of structure are presented.

Jan 1, 1984

By Feng Shuyu Yang Nianhua

According to the results of high speed photography tests, particle velocity measurement tests and the digital calculation with TP2 software, the shape of shock wave, the declined laws of the shock wave propagation speed and the peak particle velocity are described and analyzed in detail. New viewpoints about the theories of blasting fragmentation based on analysis of the progressive pictures of the fracture region are given. The formula for calculating the depth of fracture regions is established on the basis of the new viewpoints.

Jan 1, 1997