Search Documents

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Steve Dillingham

The origin of the written blasting log or shot report can likely be traced back to the earliest annals of blasting and record keeping. These records were, for the most part, a way of checking inventory, production progress, or billing, and not necessarily designed with the intention of being used as a legal document in a court of law. As our litigious society has evolved to include far reaching regulatory requirements, however, the blasting log has developed to support and aid in the defense of the common blaster from blasting lawsuits by providing a comprehensive written report of his or her actions.

Jan 1, 2002

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Steven D. Knudsen, Dale S. Preece

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: 1) modifying the gas flow portion of DMC, 2) adding a new explosive gas equation of state capability, 3) modifying the porosity calculation, and 4) accounting for blastwell spacing parallel to the face.

Jan 1, 1992

By Yong Pan, Purushotham Tukkaraja

It has been well understood that blasting is the cost-effective method for breaking rocks as compared with the mechanical systems. However, vibrations induced by blasting in open-pit mines could pose problems to the structures surrounding the mine site. Blast-induced ground vibration has been the subject of research for several studies in the past; because of the complex nature of blasting mechanism, it is difficult to predict blast-induced vibrations. Even though there are several approaches proposed by the previous researchers, traditional regression analysis is still playing an important role in predicting blast-inducedgroundvibrations.

Jan 1, 2019

By Kevin Tallent

The use of military-type energetic materials in commercial explosive products is not a new concept. In the United States, the techniques for utilizing significant quantities of surplus military explosive materials by commercial explosive manufacturers dates back to the 1950’s. At times, explosive companies have found surplus military high explosives and propellant materials to be suitable ingredients for their commercial explosive products. The availability of these military-type energetic materials has varied over the past 50 years, as a function of the military’s strategic defense needs and the advances in modern weapon technology. For the most part, the commercial explosives industry has been able to implement methods for safely incorporating military-type high explosives and propellant materials, whenever these surplus materials become available. During the past 5-6 year period, a large amount of military-type energetic materials have once again become available for recycling into commercial explosives. This situation can be attributed to a number of factors, such as the political changes in Europe, the development of more sophisticated weapons systems, and the increased EPA pressures on the U.S. Department of Defense for disposing of surplus energetic materials. As in the past, U.S. commercial explosive manufacturers have made efforts to recycle these surplus materials into their explosive products. This paper describes some of the commercial explosive products that are currently on the U.S. market, which contain rocket and gun propellants as energetic ingredients. Some U.S. explosive companies, such as DYNO NOBEL, ORICA and Slurry Explosive Corporation, have been able to recycle significant quantities of surplus smokeless powder and composite propellants as energetic ingredients into their commercial Blasting Agents. The successes enjoyed by these companies have once again shown recycling into commercial explosive products to be an economically and environmentally sound method for disposing of surplus military-type energetic materials.

Jan 1, 2000

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Luiz Felipe Mendonça de Amorim, Adimir Fernando Rezende, Gustavo Sampaio Lopes, Claudio Cesar Gajardo Arraño, Eltton de Sousa Veras, Manuel Villalobos Calderon

Many technical challenges were encountered while conducting near-field construction blasting between the critical intersection of Interstate 10 and multiple active railroad tracks in El Paso, Texas, for the Loop 375 Border West Expressway Project. Blasting was utilized for the removal of an andesite bedrock ridge in preparation for the construction of a new elevated super structure to be suspended over the existing railroad tracks. There was concern that the excessive vibrations and/or permanent rock deformation produced from the blasting within near proximity (20 feet, or 6.09 meters) of the railroad tracks would induce excessive stress and foul the tracks by shifting the alignment. This could result in a major loss of scheduling control between the two major railroad companies that operate in this area. There was also concern that the blasting may cause rock fragments to land on and interfere with critical interstate transportation. Blasts

Jan 1, 2019

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Alvin D. Christmas

The missing link is a connector between the congested downtown area of Knoxville, Tennessee adjacent to the former World's Fair site, the I_40 I_75, and Western Avenue traffic arteries. This connecter was designed to accommodate the 37,470 motorists who presently travel through these highly congested narrow paths to be replaced by the 21.8 million dollar Henely Street Connecter. All construction and blasting was to take place while existing traffic was re_routed so as to allow access between the downtown area and the vital interstate corridor. To avoid major traffic problems, the project was to be accomplished in three phases: (1) the Western Avenue viaduct demolition; (2) two new viaducts to be constructed; (3) the open box cut at Henely Street next to the L & N Depot. Due to the past attempts by the Fort Sanders Community Home Owners group and the Historical Society to stop the Henely Street Connector, this project involved a very comprehensive blasting damage control program with special provisions of .5 inches per second measured at the foundation of the closest structure.

Jan 1, 1995

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Greg Quinn

After a long week of work in Colorado Springs this past July, I was looking forward to flying home to start a long anticipated family vacation. As I grabbed my seat on the plane, a man sitting next to me innocently inquired, to the row as a whole and not to me in particular, “I wonder what the weather will be like in Phoenix”? To most people, this is a common (maybe the most common) topic of casual conversation. To a meteorologist that just dealt with six thunderstorm delays at a major golf event over 4 days, well, lets just say the smirk on my face said it all. After giving my flight mate a detailed forecast and a short explanation on why I would know such information, I sensed, correctly, the inevitable follow up question was coming. “Why would you need a meteorologist at a golf tournament?”

Jan 1, 2012

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Jianping Li, Ernesto Villaescusa, Kelly Fleetwood

During blasting, stress waves propagate through a rock mass, inducing stress and strain changes. This applied deformation affects intact rock, existing discontinuities, mine excavations, and engineered structures in the proximity of the blast. Traditionally in blasting, stress waves are quantified in terms of peak particle velocity (PPV) or peak particle acceleration (PPA), based on the method of measurement and the specified allowable tolerances. During analysis, the peak particle motion is coupled with an explosive source through various scaling laws to develop rock-specific attenuation relationships. Some studies have expanded this practice to the development of damage threshold values based on measured or predicted peak particle velocities. PPV-related thresholds are generally based on empirical models, where observation of overbreak, cracking, or fall-off are used to quantify damage. This method is often paired with the application of elastic plane wave equations to calculate the blast induced strain or the PPV threshold for tensile rock failure. Other factors that must be viewed critically in such models are the methods used to collect and analyse blast vibration data and the application of inappropriate vibration attenuation relationships.

Jan 1, 2009

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004