Search Documents

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By B. Rath

An effective process plan is an important part of maintaining consistent recoveries in mineral processing operations. Traditionally, Mineralogical studies are completed using chemical and metallurgical methods to monitor recovery and elemental distribution. The development of mineralogy and more efficient processes in mineral analysis techniques means that mineralogy is now more accessible as an efficient and comprehensive study tool. As operating costs increase and feed grades decrease it is important to maintain tight control of process and ensured maximum recovery is maintained at all times. Just a few days of losses in recovery caused by changes in ore type or processing conditions can have a large effect on total metal recovery and profit. Mineralogical audits can be used to minimize these losses by monitoring the fundamental behavior of feed ore on a regular basis. Smart use of mineralogical studies can develop mineralogical and ore type benchmarks in a detailed, which can be used in process control and monitoring. Geological ore types can be used to identify key mineralogical parameters that may be used in routine and cost effective analysis. Mineralogical systems ideally suited to this because of the depth of information on everything from modal mineralogy to locking/liberation characteristics and mineral associations. Mineralogical studies can equally be applied to specific unit operations within the process, which can allow more detailed information to be gathered on areas of the process that have been identified as critical. This will be especially effective for flotation or oxidation processes where process parameters can be very sensitive to small changes in mineralogy. This paper deals with the Ore Morphology, Ore Mineralogy, Gangue mineralogy, Photo micrographs under reflected, transmitted light and XRD studies Ore, Mineral studies of Sub grade Iron ore of Bacheli Complex, Bailadila Sector, India. Keywords: mineralogy, liberation, liberation studies, ore mineral, gangue mineral, morphology, jasper, ferruginous clay

Sep 1, 2012

By P. Somasundaran

While sustainability itself needs to be redefined in a selfless way, methods of measuring and optimizing it also need to be reformulated. Gone are the days when we had the luxury of abundant resources and the freedom to extract values in self-centered ways. In the past, focus has been mostly on reagent performance, processing operations, and upgrading of tools to maximize rather than optimize value extraction from the earth's crust. Today we as extractors face a new set of challenges that include value separation from low quality resources including wastes, but within the energy, environment, and societal constraints. Development of such technology depends on understanding the role of entities and concepts such as bio-molecular interactions at surfaces, forces involved in inter-granular versus intra-granular fracture in new fragmentation methods, robotic in-situ or extraterrestrial mining, exploiting new membrane and nano technology, use of new sensors and actuators for detection and separation and computation capabilities for faster and economical processing. Equally importantly, we need to communicate with everyone what we foresee and anticipate when we extrapolate the type-performance-cost relationship of ores to the era ahead of us and establish viable schemes for ecological survival. Keywords: sustainable mineral extraction

Sep 1, 2012

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Shirchinnamjil Nyamdelger, Atsushi Shibayama, Narankhuu Ariunbolor, Gunchin Burmaa

In this study, the authors investigated the capability of an acidic thiourea solution and silicon-organic polymers (PSTM-3c, PSTM-3T) as ion-exchange resins to recover of gold from gold-bearing ore concentrates. Firstly, elemental gold present in flotation concentrates was dissolved by leaching with a solution of nitric acid and thiourea under the optimized conditions. The best result on gold thiourea leaching was obtained under a nitric acid concentration of 2 N, thiourea concentration of 2 %, and oxidant (Fe2(SO4)3) concentration of 3 %, solid:liquid ratio (S:L) of 1:20, leaching time of 6 hours at 20 °C with a gold recovery of 93.7 % for a gold flotation (unroasted) concentrate. For the roasted gold concentrate, the dissolution of gold was 94.8% under the optimized leaching condition as nitric acid concentration of 0.5 N, thiourea concentration of 2 %, and the oxidant concentration of 1 %, S:L ratio of 1:10, leaching time of 4 hours at 50 °C. Secondly, a series of sorption tests was carried out on a pregnant leach solution containing gold complex Au[S=C(NH2)2]2+ using silicon-organic polymers (PSTM-3c and PSTM-3T), respectively. The effects of solution pH, adsorption time and temperature in the sorption process are also studied. As the results, the PSTM-3c and PSTM-3T polymers were adsorbed about 94.4 % and 95.1 % gold from the pregnant leach solutions under the optimum sorption conditions, respectively. It was found that the both PSTM-3c and PSTM-3T polymers were effective for the recovery of gold from the pregnant leach solution of thiourea. Adsorption activity of the PSTM-3c and PSTM-3T polymers was confirmed by new peaks near 1700 cm-1 in the FT-IR spectrum of the gold-adsorbed polymers, respectively.

Jan 1, 2014

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By Christopher Tucker, Marcello Veiga

Social issues are increasingly recognized as significant inhibitors to mineral development projects. Increasingly social risk is being recognized as a key factor determining the success of a mineral investment. Groups opposed to a mine for social or political reasons often use environmental impacts, real or perceived, to prevent mine development. These risk factors depend largely on cultural perceptions of mining activities and must be understood as such in order to be appropriately managed. A first step to addressing social issues is inclusive, transparent and meaningful engagement of stakeholders. This process allows stakeholders to understand what the other parties value in order to collectively establish a common currency for development and the creation of mutual value. Expanding the scope of benefits and values a mine can bring is of increasing importance to mining companies who typically consult outside specialists remote from the mine site and late in the development timeline for this purpose. Training technical staff, engineers and geologists, who make initial and ongoing contact with local interests, in a holistic approach to mine development is crucial to successful and economic mineral development projects. Further extending this conversation to the general public, media governments and non-governmental organizations is a necessary step in developing a meaningful discourse on the benefit of mining activities.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By Fernando Concha

"Thickening development and innovation in the 20th Century occurred in two decades periods. From 1900 to 1920, Dorr invented the continuous thickener and the first method of thickener design was proposed by Coe & Clevenger. From 1920 to 1940, the operating variables of continuous thickening were discovered by Comings at the University of Illinois. From 1940 to 1960, the first theory of sedimentation was proposed by Kynch and several authors, Talmage and Fitch, Ysioka and Hasset used this theory to develop new thickener design methods. From 1960 to 1980 Shannon and Tory demonstrated that this theory applied exactly for the sedimentation for small rigid spheres in water and Scott showed that it is not valid for flocculated suspensions. From 1970 to 1990 the phenomenological theory of thickening was developed based on the theory of mixtures. Papers by Kos, Bascur, Thacker and Lavelle, Concha and Bascur, Concha and Barrientos, Auzeris, Buscal and White, Landman, White and Buscal show the application of this theory to thickening and Adorjan presented the first thickener design method based on this theory. In 1980s the mathematical analysis and solutions of Kynch’s model for batch and continuous thickeners was obtained by Bustos. The new Century brought solution to the phenomenological thickening model which was applied to thickener design, simulation and control. The method of thickener parameter determination was improved by designing new laboratory and on-line instruments and advanced control strategies was designed and validated in plants. Structural thickener design produced improved feedwells and feed dilution mechanism, stronger raking mechanism and different thickener shapes according to new ambient requirements, such as high rate thickener and paste thickeners that increase the water recovery. New challenges include better flocculation and advanced control strategies."

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By A-M Ahonen

The paper discusses the experiences of a fast-track curriculum designed to provide the industry with engineers capable of working in minerals processing industry. The course has been done once before and the second course has been started. Students chosen have graduated from other fields of engineering. For the first course, twelve students were chosen from 152 applicants and for the second the twelve students were chosen from 96 applicants. The basic idea of the curriculum is to alternate between theoretical studies at the university and working experience periods at industrial sites. In addition, there are several one week assignment tasks at industrial sites. The theoretical periods are six to eight weeks long and there are three of them. During the first period, the teaching concentrates on unit processes and their chemical and physical background. The theme of the second period is mineral engineering systems; flowsheet development, process dynamics, control systems etc. The last theoretical period teaches environmental issues, leadership, project work and other similar topics. Each of the theoretical periods ends with an assignment week at industrial sites. The assignments are designed to wrap up the teachings of the period. For the industrial periods, the students are given learning goals, which have been discussed and designed with their industrial mentors. They are required to find relevant literature, make experimental designs, implement those designs, present the data, and make conclusions of their results. During these periods, a weekly meeting over the Internet is compulsory. Keywords: mineral processing, flowsheet development, process dynamics, control systems, constructivism, zone of maximal development, Vygotsky

Sep 1, 2012

By V. Yu. Ivanov, A. I. Yuryev, L. S. Lesnikova, M. S. Datsiev

"The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before. In 2003-2005, the process upgrading included the differentiated processing of nickelpyrrhotite products recovered at the different concentration stages and made it possible to significantly enhance the contrast of the pentlandite and pyrrhotite flotation properties and to simultaneously increase separation of polymineral intergrowths.The next stage of the PD concentration complex development is the Project ""Talnakh Concentrator Reconstruction and Technical Upgrading"" to raise its capacity by half. The project has three Phases.• Phase 1. Pilot startup was carried out in January 2015 following the installation of new OK-100 TC flotation machines, manufactured by Outotec.• Phase 2. The introduction of a new technology developed by the Polar Division specialists launched in mid-2016. The new technology is based on maximization of iron and sulfur removal into tailings and maintenance of non-ferrous and precious metals losses at the same level.After the realization of Phase 3, the annual capacity of the Talnakh Concentrator will raise by another ~ 40% at the expense of processing cuprous and disseminated ores currently being processed by the Norilsk Concentrator.By 2023, due to upgrading of the PD production facilities the emissions to the atmosphere will reduce by 75%.Polar Division of PJSC MMC Norilsk Nickel (PD) searches for the ways to solve its environmental issues. Thus, in 2016, the Nickel Plant was shutdown and a new flowsheet was introduced at Talnakh Concentrator. It resulted in the reduction of sulfur specific amount sent to pyrometallurgical processing as a component of the concentrates.The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 1981, its design capacity for processing of Cu-Ni ores from Oktyabrsky and Taimyrsky Mines did not exceed 3 million tons per year.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented at the Talnakh Concentrator, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before."

Jan 1, 2018