Search Documents

By S. E. Boyd

Studies of benthic recolonization following the cessation of dredging in U.K. waters and elsewhere are limited, and are largely confined to experimental circumstances. Investigations of the physical and biological status of licensed areas in the U.K. at various times following cessation of commercial dredging are very limited and so judgments as to the likely progress towards environmental restoration and the time-scales are often based on predictions rather than real data. This study was established to address this deficiency by assessing the status of seabed substrata and associated benthic fauna within and outside areas where dredging had ceased and to conduct follow up sampling to monitor progress towards full recolonization.

Jan 1, 2004

By B. Prause

Ferromanganese crust samples collected from Central Pacific sea-mount areas became of special interest after surprisingly high nobel metal contents have been analyzed. Hydrogenetic crust growth is controlled by the conditions of the oceanic water column. Thicker encrustations show two crust generations of different age ranges. The mean values of the chemical composition state that the older generation is richer in P, Ca, Ni, Cu, Zn, and Pt and depleted in Fe, Ti, Co, Al, and Si. The differences apparently indicate a distinct change of the geochemical environment. The Pt concentrations vary up to 1800 ppb and do not clearly correlate to one of the other metals. This might indicate a bond of multiple nature. Several mechanisms have been proposed to explain the Pt concentrations in ferromanganese samples. Our models consider seawater and cosmic spherules as responsible Pt sources. In seawater the main species of dissolved Pt probably exist as the doubly negatively charged tetrachloro-complex. A precipitation of Pt in seawater may take place if the chloro-complex is decomposed by reduction of pt2+ to pt0. On the other hand, the Mn02 precipitation is caused by an oxidation of Mn2+ which is supplied from the oxygen-minimum zone. The large activation energy needed for the oxidation of divalent ~n" in solution has been recognised, and the resulting slowness in the formation of Mn(V1)-oxihydrate sug

Jan 1, 1989

By Peter E. Halbach, Andreas Jahn

Co-rich hydrogenetic ferromanganese crusts are typical marine interface products of growth processes taking place on sediment-free substrate rocks on the seafloor. They grow very slowly and preferentially in water depths below the oxygen-minimum zone (OMZ) and have so far been found even in water depths of up to more than 5000 m, i.e. also below the calcite compensation depth (CCD); these deep ferromanganese crusts are particularly rich in Fe. It is assumed that the O2-minimum zone is the most important source layer of dissolved manganese, the decomposition of fecal pellets here also contributes to this Mn-budget. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical as well as a surface-chemical mechanism. Microbial mediations can be assumed, in particular since steps of redox-reactions are involved. The two main components of the hydrogenetic substance are hydrated d-MnO2 (vernadite) and x-ray amorphous Fe-oxyhydroxide, both of which are intimately intergrown with each other forming the extremely fine-grained hydrous oxidic material. In seawater, elements occur as dissolved hydrated ions or as inorganic as well as organic complexes which, in general, have either a positive or a negative surface charge depending on the pH of the respective marine environment. These complexes form hydrated colloids that interact with each other or with other dissolved hydrous metal ions. The main agent to oxidize the dissolved Mn2+ ions is oxygen, transported upwards from deeper water by turbulent eddy diffusion and turbulent rise processes at seamount slopes.

Jan 1, 2017

By Terence Day

The traditional approach to mineral resource development is to identify the resource and then to undertake an environmental impact assessment of the effects of developing the resource. However, the traditional approach tends to ignore or underestimate cumulative, indirect and synergistic effects (Therivel et al., 1992). Moreover, traditional environmental impact assessment puts the project proponent in a position where the environmental impact assessment is used to defend on environmental grounds, a decision which has already been taken on technical and economic grounds. An alternative approach is to undertake an area-wide or strategic environmental assessment, (United States Department of Housing and Urban Development, 1981; Kelly et al., 1987). Strategic environmental assessment consists of the compilation and analysis of environmental data and information on an area. The data and information includes physical and chemical oceanographic data, biological surveys, social and economic parameters such as recreation and resource use, and ecosystem stressors such as dumping areas and sewage outfalls. Strategic environmental assessment is being increasingly used in the U.S. to provide scientific information to evaluate national or regional objectives for development and conservation of coastal and oceanic resources (National Oceanic and Atmospheric Administration, 1991). The strategic environmental assessment process lends itself very well to an evaluation of offshore sand and gravel re- sources in Atlantic Canada, because although the potential resource is widespread, the environmental constraints on development are potentially serious, but highly variable. The approach has the merits of identifying areas which are least susceptible to environmental damage, and of concentrating the exploration efforts on that part of the resource which is most viable from the perspective of integrated resource management and marine conservation.

Jan 1, 1995

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By Kiseong Hyeong

The Intertropical Convergence Zone (ITCZ), where the southeast and northeast trade winds converge, is the effective climatological barrier that separates the southern and northern hemispheres in terms of dust budget. Asian and N. American dusts dominate in the Pacific north of the ITCZ, while Central and S. American dust prevails south of the ITCZ. In order to understand the nature of latitudinal and depth-related variations of mineral composition in terms of position relative to the ITCZ, deep-sea core sediments were collected from 9°N to 17°N at a 2° intervals along the 131.5°W meridian and analyzed for mineral composition. The amount of illite in surface sediments decreases gradually from 65% at 17°N to 31% at 9°N. In contrast, smectite increases from 11% to 56% southward. The observed mineralogical variation toward the ITCZ is attributed to the increased supply of volcaniclastic material transported via the southeast trade winds from the Central and South America source regions. Smectite-illite transition, a phenomenon that the amount of smectite increases over illite, occurs at around 10°N, the northern margin of the ITCZ. This result indicates that the change in latitudinal position of the ITCZ in the geological past could be recorded by the smectite-illite transition in deep-sea cores. The cores studied show down-core variation of mineral composition from illite-rich at the surface to a smectite-rich clay suit at depths, similar to the latitudinal variation. The smectite-illite transitions observed in these cores are likely the records of changes in latitudinal position of the ITCZ. The depth and age of the smectite-illite transition is getting shallower and younger towards the equator, implying that the ITCZ was located farther north during late Tertiary and has shifted southward to the present position of 5°N~10°N.

Jan 1, 2004

Ancient volcanogenic Cu-Zn-Pb-Ag-Au massive sulfide ores commonly have associated with them along strike and in the immediate hanging wall a distinctive sediment that is thin, usually cherty and metal enriched, and generally referred to as an "exhalite horizon" or "tuffaceous exhalite". Typical examplks include the 13 Ma tetsusekiei of the Kuroko deposits of Japan (Kalogeropoulos and Scott, 1983, Econ. Geol.) and the 2700 Ma contact tuffs of Noranda, Canada (Kalogeropoulos and Scott, 1989, Can. J. Earth Sci.) and Key Tuffite of Mattagami, Canada (Liaghat and McLean, 1992, Explor. Min. Geol.). Attempts to use trace element distributions as lithogeochemical guides to ore have been largely unsuccessful. Exhalites have been considered to be the products of seafloor hydrothermal activity that is peripheral to the main ore-producing vents. However, large actively-forming polyrnetallic sulfide deposits at the Explorer mid-ocean basalt spreading ridge (1 850 m depth) in the NE Pacific and the eastern Manus back-arc dacitic spreading center (1650 m depth) in the western Pacific have demonstrated that the exhalite horizons are more likely produced by fallout of particulates from the main hydrothermal plume. In a typical hydrothermal plume, grains of >27 µm represent up to 97% of the mass (although only 2% of the population) of the particulates and are calculated by Stokes equations to fall from the plume to the seafloor within a few krn of their source. The particles are primarily composed of anhydrite, barite, amorphous silica, iron oxyhydroxides and metal sulfides and oxides. Plumes are subject to bottom currents which push them in preferred directions, just like smoke plumes in the atmosphere are subject to the vagaries of wind direction. Bottom currents in the deep ocean can be 50 m/min or

Jan 1, 1993

By B. J. Bluck

Diamond mega-placers, in order to rank amongst the primary diamond deposits, are defined as => 70 m carats at =>95% gem quality. There is only one mega-placer known and that is found along the coast of southwestern Africa fringing the Kaapvaal craton. Placers are classified as residual when they are left on the craton, transient when being eroded into the exit drainage and terminal. Terminal placers, in being the final depositories of diamonds off the craton, have the greatest probability of being a mega-placer and such is the case in the placer deposits near the Orange River mouth, southwestern Africa. There are four main groups of conditions leading to the development of a mega-placer: the craton, the drainage, the nature of the environment at the terminus and the timing. The craton, in its role as the producer of diamonds is significant in respect to its size, diamond-fertility, the degree to which diamonds from successive kimberlite intrusions have been retained there and their availability to the final drainage yielding the mega-placer. Cratons in being buoyant have a tendency to leak diamonds into surrounding basins but in being incompressible often have orogens converge onto them resulting in lost sediment being returned as foreland basin fills. In order to concentrate a bulk of diamonds the drainage basin has to be large with a high proportion of it on the craton. The drainage yielding the mega-placer should ideally not have been preceded by older drainage and other systems that may have robbed the craton of earlier diamonds. The exits of diamonds from the craton need to be few in order to focus on their supply and the drainage network needs to be efficient in order to remove the maximum volume of diamonds off the craton. This efficiency and the focused termination is best achieved by the rejuvenation of a pre-existing drainage network. The drainage should be young enough to yield host sediments friable enough to allow brittle diamonds to be recovered from them.

Jan 1, 2004

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

By James R. Hein

Low- to intermediate-temperature, diffuse-flow hydrothermal fields and associated mineral precipitates have been found at many locations along oceanic spreading centers, back-arc basin spreading axes, and midplate hot-spots. However, this type of hydrothermal field has not been found in oceanic fracture zones until recently. We mapped and collected samples from an active hydrothermal field in the Blanco Fracture Zone (BFZ) located in the northeast Pacific. The BFZ connects the Gorda and Juan de Fuca spreading centers and is divided into east and west segments by Cascadia Depression, a small spreading center. Small pull-apart basins occur along both the east and west segments. A complex set of basins near the western end of the BFZ includes from east to west, Surveyor Depression, East Blanco Depression (EBD), and West Blanco Depression. The hydrothermal field described here is located in the EBD.

Jan 1, 2001

By Marco Figoni

The increased interest on deep water minerals resources is a challenge for both mining and oil industry. The exploration and production of oceans minerals require a synergy between of different technologies. While mining industry is leading the dredging and processing part of the system, oil industry is contributing through development of ore lifting technology based on existing subsea knowledge. The paper presents an overview, based on published projects around the world, of different approaches to marine mining. Several exploration techniques and offshore production systems were already designed and assessed, all of them with apparently positive results. Exploration phase is well advanced and in continuous expansion allowing the discovery of increasing resources around the world of different nature but production can be considered to be in an early stage. Different from onshore mining, subsea operations require a closer cooperation with international and local authorities to preserve as much as possible the environment. There are still many uncertainties at respect and all the exploration process must be carefully evaluated to allow subsea mining to develop in a sustainable manner. Technically, mining at seabed was already demonstrated and the process is based on three main components, namely seafloor mining tools, riser and lifting system and production vessel support. This layout is based on the concept that ore must be disaggregated at seafloor first, transported to surface in form of slurry that must be dewatered before loading to be transported to processing plants onshore. The challenges are rising because the environment and safety must be taken into consideration as a priority when evaluating the efficiency of the system. The most critical challenges regarding the production operations, especially in deep water are the deep-sea excavation process, the transport of large slurry volumes, the slurry abrasivity, the power supply management and the subsea

Sep 14, 2011

By Chan Min Yoo, Jung-Keuk Kang, Wonnyon Kim

Recently high-resolution paleomagnetic age determination of ferromanganese crust in less than millimeter scale has been successfully carried out using a superconducting quantum interference device microscopy magnetometer (SMM). However, it has not been clearly identified how the crust is keeping ancient geomagnetic field records. Here we try to identify magnetic mineralogy of the crust obtained in the Magellan Seamounts, the West Pacific (~20 °N). As a record, age of the crust used in this study is extended to ~10 Ma at ~40 mm depth and ~28 Ma at ~100 mm depth, respectively, based on the combination approach of SMM measurements, Be-isotope and Co-chronology. Thermal demagnetization revealed a Curie temperature of ~560oC, corresponding to (titano)magnetite. Component analysis of isothermal remanent magnetization identified a presence of two types of magnetite. Measurements of first order reverse curve showed a dominance of non-interacting single-domain magnetite, which is one of the intrinsic feature of biogenic magnetite. Although most of the magnetic particles on transmitted electron microscopy are covered by amorphous Fe-Mn minerals, some are observed as a prototype of biogenic magnetite showing a chain of ~10 nm sized magnetite cubes. However, a magnetite signal (i.e., Verway transition at ~ –120 oC) was not detected in low-temperature treatment probably due to surface oxidation of magnetite. Contribution of interacting magnetite of detrital origin is <30% throughout a crust. Interestingly, contribution of detrital magnetite is almost three times higher since ~10 Ma. At this boundary, a growth rate of the crust is double up and flux of other detrital signals, including Al, Mg, Ti and Zr, are also increased.

Jan 1, 2017

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By Kokichi Iizasa

Kuroko-type deposits exist in Japanese EEZ. Some of them are present in the Izu-Ogasawara oceanic island arc south of Tokyo. Major two Kuroko-type deposits occur in the area. One is the Sunrise hydrothermal field occurring on the caldera floor of Myojin knoll, which is likely to be the developed stage in sulfide mineralization. Another is present in the crater of Suiyo seamount that is the early stage of sulfide mineralization. The two deposits are here presented on the growth history based on samples recovered by Benthic Multicoring System (BMS).

Jan 1, 2002

By Fred C. Dobbs

To effectively manage the potential environmental impacts of deep-sea mining of manganese nodules, we need to know substantially more about the effects of sediment redeposition on abyssal communities and the time scales of recovery from such effects. As an initial step towards a predictive understanding of mining impacts on abyssal benthos, we are conducting a series of biological studies within the framework of the Benthic Impact Experiment (BIE). Mining operations will cause resuspension of sediments across extensive areas of the abyssal Pacific Ocean. The resultant plumes likely will produce redeposition layers, ranging from a few sediment grains in thickness to > 1 cm, over thousands of square kilometers of the seafloor. The impact of such redeposition on abyssal benthic communities is exceedingly difficult to predict. While there has been speculation that redeposition of 1 mm or less will exert deleterious effects, there has been very little testing, and the BIE will provide the first in situ test of redeposition impacts. In a series of cruises before and after controlled resedimentation, we are collecting biological samples to determine the undisturbed state of the ecosystem, the immediate effects of disturbance, and the time-course of recovery resulting from quantified levels of resedimentation.

Jan 1, 1992

By Akira Usui

Iron and manganese are very mobile metallic elements in the surface aqueous environment, particularly in the oceans. The elements are easily precipitated as oxides or dissolved back into water, controlled mainly by redox conditions, and the oxide precipitates often selectively accumulate other metallic elements. We have found clear evidence of fine-scale variations in chemistry, mineralogy, isotope composition and microstructures within various iron-manganese nodules and crusts, such as in the deep-sea basins and seamounts of the Pacific Ocean, and in shallow waters in the Baltic Sea. The patterns of variation with depth (that is time-lapse profiles of the deposits) are often correlated among samples and sometimes between remote localities. These fine-scale variations most probably reflect past depositional conditions and possibly image the environmental change, although they remain to be correlated to any physicochemical, geological, or oceanographic parameters. The hydrogenetic ferromanganese crusts have grown widely in the northwestern Pacific, accelerated by intensive circulation of oxygenated bottom waters during the last several millions of years, or earlier. The fine-scale (in millimeter) in-depth compositional and textural patterns with Be-10 growth-rate curves suggest significant changes in growth rate and also occasionally show a common microstratigraphic pattern among samples. Some of the samples indicate a correlation in growth pattern between remote locations, while others suggest short-range difference of oceanographic conditions with water depths.

Jan 1, 2004

By Sophia Katsouri

Hydrothermal circulation that produces sulfide deposits in the marine environment can also produce sulfide deposits in lakes. The major differences in terms of process are (1) in lakes the hydrothermal fluid is meteoric water of low salinity whereas in the marine setting it is saline and (2) the rocks that are leached of metals to produce the deposits are continental crust in one case and oceanic crust in the other. We have examined sulfides that are presently forming in two lakes ? Lake Tanganyika in east Africa and Lake Oyunuma in Hokkaido, Japan. Tanganyika is the second largest lake in the world and the second deepest rift lake, after Lake Baikal in southeastern Siberia. Two hydrothermal fields are known in its northern basin at Pemba and Cape Banza (Tiercelin et al., 1993). At Pemba, CO2 and CH4-rich, low temperature (53-88°C) hydrothermal fluids are forming decimeter-tall chimneys at 2-46 m water depth. Our microscopic and x-ray diffraction study of samples from the Pemba site reveal marcasite and pyrite to be the most common sulfides. Minor minerals include barite, hematite, bornite and chalcopyrite. Quartz and feldspar are also identified and were probably incorporated from the surrounding lake sediments. At Cape Banza, aragonite chimneys, up to 70 cm high, are venting fluids at 66-103°C.

Jan 1, 2001