Search Documents

By Andrea Koschinsky, Luise Heinrich

(for an oral presentation) Activities for preparing future deep-sea mining offer the unique opportunity to study environmental conditions and anticipate adverse environmental impacts prior to the commercialization of the activity. Until know, environmental research has first and foremost focused on understanding direct impacts occurring at the seafloor or in the water column such as the removal of substrate, the suspension of sediment or the creation of particle plumes. Impacts occurring above the sea surface have thus far rarely been considered. The operation of deep-sea mining equipment, as well as of mining and transport vessels will be associated with a considerable energy demand. In the open ocean, this energy will be provided by heavy fuel oil (HFO), which is the cheapest and most common marine fuel. The combustion of HFO will be associated with the release of greenhouse gases and other pollutants. Deep-sea mining will thus directly add to already critical air pollution levels caused by international shipping. To contribute to a holistic assessment of deep-sea mining impacts and to address the previously outlined knowledge gap, we present the methodology to quantify the fuel consumption and associated emissions of a potential typical commercial manganese nodule mining operation in the Clarion-Clipperton Zone (Fig.1). Using the mine set up and energy demand estimates from a study commissioned by the German Federal Ministry of Economic Affairs and Energy supplemented by information from literature, we anticipate emissions of carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), nitrous oxide (NO2), nitrogen oxides (NOx), sulfur oxides (SOx), particulate matter and non-methane volatile organic compounds.

Jan 1, 2018

By Andreas Kaede

INTRODUCTION Due both to the political history of UNCLOS and the sensitivity of the ocean floor and environment to man made impacts, both the Convention (including also the 1994 Amendment) and subsequent codification (such as the ISA draft code on Exploitation of Mineral Resources in the Area) put a focus on information about, and conveyance of, technology employed by interested deepsea mining companies, to inter alia the Authority and developing countries. In contrast, companies usually are (or by their nature should be) interested in safeguarding their technology and business secrets in order to secure unique selling propositions in a competitive environment. On the background of the meanwhile maturing regulatory régimes on deep sea mining, the presentation will look into some of the key regulatory provisions mirroring these apparently antagonistic interests, how the players involved could deal with them, and how they might in some cases be reconciled. Progress of Presentation The presentation will start by briefly examining some classical methods of protection of technology, such as patents, copyrights, and (not the least) secrecy. It will be found that some of the statutory means of protection due to their territorial character may face problems in being implemented in areas outside national jurisdiction, such as the Area, but that, thinking globally, they nevertheless retain much of their value for the purpose of protection. Depending on available presentation time, a model case may be used to illustrate the above – and also some of the following – findings.

Jan 1, 2018

By Justin C. I. Baulch

In October 2004 Placer Dome entered into an exploration farm-in agreement with Nautilus Minerals, to explore for Submarine Massive Sulphide (SMS) deposits on Nautilus? PNG exploration tenements. Placer/Nautilus currently holds approximately 15,000 km2 of tenements in PNG waters, either granted or under application, covering all reported seafloor hydrothermal vent occurrences.

Jan 1, 2005

By Irina A. Pulyaeva

Hydrogenetic Fe-Mn crusts play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Most Fe-Mn crust deposits occur on the tens of thousands of seamounts found in the global ocean as well as on ridges and plateaus. Because of these circumstances, it is essential to clarify a number of outstanding issues with regard to Fe-Mn crust history and development, including controls on metal sources and concentrations. The first-order characteristics of Fe-Mn crusts as potential ore deposits include concentrations of metals (grade) and the thickness of crusts (tonnage), which vary depending on Fe-Mn crust structure and texture. Data on the structure, composition, age, and deposit characteristics will help define which factors are key for the creation of mineral accumulation and which combination of factors leads to the formation of potentially economic concentrations of metals. In this paper, we address the structure and characteristics of Fe-Mn crust stratigraphic sections collected from Central and Western Pacific seamounts. We describe the changes in mineralogical and chemical compositions of crust layers of different ages, the occurrence and regional distribution of these layers that correlate regionally, and reconstruct the paleoceanographic conditions that influenced crust growth.

Jan 1, 2010

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

In the western Woodlark Basin, propagation of seafloor spreading is occurring directly into the continental crust of Papua new Guinea. The spreading is not strictly in a back-arc tectonic setting, rather it appears associated with microplate rotations related to the complex convergence of the Indo-Australian and Pacific plates in the southeastern Pacific region. Volcanic rocks along the western Woodlark spreading axis range from normal mid- ocean ridge basalts to basaltic andesites with back-arc geochemical affinities. Rare peralkaline rhyolites also occur. Hydrothermal deposits occur at a basaltic andesite volcano located on the neovolcanic zone near its westernmost propagating tip. Franklin Seamount is a 250m-high cone constructed largely of pillow lavas and talus which sits astride a 450m-high ridge of similar lavas oriented subnormal to the spreading direction. At its crest, 2150m below sea level, there is a 100m-deep caldera.

Jan 1, 1993

By David G. Jones

Radiometric surveys of the beach and nearshore zone of the Dutch Frisian Islands have identified sands enriched in heavy minerals. The areas of heavy mineral concentration have been mapped in detail using a state of the art towed gamma-ray detector, which gives improved sensitivity through the use of new detector materials and improved data processing techniques. The detector provides continuous measurement of sea floor radioactivity (and of a number of other parameters) and can be used simultaneously with other survey techniques, such as echo sounding, sidescan sonar and shallow seismic profiling. It enables a rapid, and cost effective, assessment of the surface distribution of heavy minerals to be made. The heavy mineral suite includes magnetite, ilmenite, garnet, rutile and zircon. These minerals contain 1-3 orders of magnitude more U and Th, in terms of their activity concentrations, than the accompanying light minerals (mainly quartz). Since the heavy mineral composition of the sands appears to be relatively constant along the Dutch Frisian Island chain, the U and Th concentrations can be used to provide a quick estimate of the heavy mineral content. The sea floor radiometric measurements allow sediment sampling for more detailed analysis to be highly targetted. The zones of heavy mineral enrichment are generally sub-parallel to the coast and are usually confined to water depths of 5-10 m. There is a close correlation with sand bars on the shoreface, the highest radioactivity typically occurring just seaward of the crest of these features. As well as being used for heavy mineral exploration, similar radiometric methods can be applied to mineral processing. Gamma-ray detection systems can be used to provide rapid analysis in the process stream enabling on-line grade control and optimisation of processing, from excavation of mineral sands to the final products.

Jan 1, 1995

By Winston Rocher Anda

Traditionally, mining activities have been developed in firm land, but technological advances and human needs have opened in the last year?s new opportunities in the maritime field. This has happened not only in the oil or hydrocarbons industries, but also in relation to the exploration or exploitation of other minerals, metallic and non-metallic. This has forced several countries to complement or create legal rules that make possible its own development and the International Law, through the United Nations Convention on the Law of the Sea, to regulate this activity in the space of its own, the calling area. Chile, as country with a long experience in mining and great advances in large deposits exploitation, possesses a special juridical frame that regulates this economic activity according if it is the geographical or territorial area in which is realizes, and it has been complemented lately with the international normative.

Jan 1, 2011

By R. Moss

Gold and silver are important byproducts of mining volcanogenic massive sulfide (VMS) deposits. Both metals occur in VMS deposits ranging in age from the Archean to the currently forming massive sulfides found on the ocean floor. The gold- and silver-rich deposits on the modern seafloor are geographically diverse and occur in several different tectonic settings (Figure 1a,b) including seamounts (e.g. Franklin Seamount, Papua New Guinea), unsedimented mid ocean ridges (e.g. TAG and Snakepit, Mid Atlantic Ridge), sedimented mid ocean ridges (e.g. Escanaba Trough) and back-arc basins (e.g. Manus Basin, Papua New Guinea). Interestingly, the most gold- and silver-rich deposits are found in the back-arc basins of the western Pacific, commonly associated with differentiated volcanic rocks such as the dacite-rhyodacite suite at PACMANUS in the eastern Manus Basin. This suggests that different, or more efficient, mechanisms are concentrating precious metals in such back-arc settings. Such mechanisms may include leaching of volcanics enriched in gold (e.g. rifted arc crust) or silver (e.g. continental crust) and/or the introduction of gold into a hydrothermal system by a magmatic fluid. The gold content of modern seafloor precipitates varies from a few ppb up to a high of 54 ppm reported from eastern Manus Basin (1). The Jade Deposit in the Okinawa Trough has the highest silver contents with values up to 1.1% (2). Both gold and silver are preferentially concentrated in late-stage, low temperature precipitates with zinc-rich assemblages being favoured in most cases. Gold is found as relatively pure native gold and sub-microscopic inclusions in gold-rich deposits, but occurs predominantly as sub-microscopic inclusions and possibly as solid solution in the gold-poor deposits (3). Silver occurs as rare silver minerals such as acanthite and native silver in the silver rich Jade deposit (2), but more commonly in the silver-containing minerals tetrahedrite and tennantite, as is the case in the PACMANUS deposit. Tetrahedrite is also known to be an important host of silver in ancient VMS deposits (4). More abundant sulfides can contribute significantly to the silver balance. In the silver-poor deposits at 21 N East Pacific Rise, silver is contained entirely within chalcopyrite, isocubanite, pyrite, marcasite, sphalerite/wurtzite and galena. In this case silver may be present as sub-microscopic inclusions of silver minerals or in solid solution.

Jan 1, 2011

By Michael W. Milner

Cold Ocean Placers: Polar storms, interstadial littorals and crustal adjustments. Polar storms with consistent strong winds in the Southern, Antarctic Ocean are responsible for placer deposits on both the east and west coasts of Australia, on the west coast of New Zealand, as well as on the coasts of South America and Africa. Arctic winds, confined by both land and ice, generate similar placers in Labrador and Greenland as well as on the coasts of Scotland, Norway, Hudson's Bay, Nome, Goodnews Bay, Kamchatka and the north coast of Siberia. Tasman and Labrador seas have several parallels to Newfoundland, including north-south polar waterways, young spreading ocean floors, and youthful coastal escarpments with glaciated coasts. Black sand beds in beach deposits on the modern and Pleistocene transgression strandlines, skewed to the distal ends of beaches, and set into either bedrock or sediment fill, are the locus of the light-heavy mineral placers with titanium, zirconium and rare earth elements; chromium; iron; and tin. Gold and platinum group elements are the ultra heavy minerals at one end of the spectrum and tend occur in proximal placers generated, either directly from bedrock sources, or as minor by-products in distal light-heavy mineral placers. Diamonds are unusual in that the value is only in the larger stones, despite the formation of beach sand and aeolian placers in the littoral zone, and the sites of concentration are in very high energy bedrock traps, on terraces that are mined to depths of 100 metres below sealevel.

Jan 1, 1995

By Virginie Tilot

Recommendations have been drafted following an international multidisciplinary panel discussion organized at UNESCO/IOC by the Académie des Sciences d?Outre-Mer on 15 December 2010 conveyed, according to its mandate, to the French government and to an international pool of scientists and stakeholders. These take into consideration the relevant Provisions of the United Nations Convention on the Law of the Sea of 10 December 1982, the Rio ?Earth Summit? Convention of Biological Diversity of 5 June 1992 as well as the activities and recommendations implemented for the world?s oceans and seas, in particular by the International Seabed Authority (ISA) and the recent reports and scientific works (including those implemented by the ISA Kaplan, Ifremer, COI-Unesco). The recommendations integrate, for one of the ecosystems, the conclusions of the project of the conclusions of an IOC-UNESCO / Government of Flanders project (2004-2010) implemented by Dr. V. Tilot from 2004 to 2010, during which were published three volumes describing the referential state of the polymetallic nodule ecosystem and proposing options for the management and conservation of the nodule ecosystem in the Clarion Clipperton Fracture Zone, NE Pacific Ocean: http://unesdoc.unesco.org/images/0014/001495/149556f.pdf, http://unesdoc.unesco.org/images/0014/001495/149556e.pdf; http://unesdoc.unesco.org/images/0014/001495/149556e.pdf#223

Jan 1, 2011

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By Tina Schneider

Scientists show that polymetallic nodules and massive sulfides from deep sea mining contain valuable metals. These metals have the potential to overcome future shortages of supply. Hence, companies, government agencies and industrial associations increasingly evaluate deep sea mining as a promising supplement of land mining. Technologies to extract, exploit, transport and smelt polymetallic nodules and massive sulfides industrially are still in conceptual stage and not sufficiently advanced for operation. According to the International Seabed Authority, large scale exploitation would require a successful pilot mining test in order to demonstrate e.g. the technological feasibility but also the conservation of environmental systems services. At the same time, NGO´s and a some scientists point out that large scale extraction of polymetallic nodules and massive sulfides could disturb the habitat of benthic organisms, with unknown long-term effects. Aside from the direct impacts of mining, indirect consequences about leakage are likely. In the oral presentation I will show how companies, government agencies, scientists and association/interest groups perceive and assess economical/technological, social and environmental risks and opportunities of deep sea mining. In order to analyze the perspectives of each stakeholder group on deep sea mining, we conducted 15 interviews with four stakeholder groups and a large scale survey (n = 500, return rate = 13 %) in Germany. We used the concept of sustainability with its economical/technological, ecological and social dimensions for the interpretation of the results. The empirical research shows the following core results:

Jan 1, 2018

By Tobias Hens, Andrew Frierdich, Joël Brugger

The rapid advancement of green technologies in recent years is closely tied to an ever- increasing demand for raw materials. Innovative forms of zero-emission transportation and sustainable power generation will require a variety of traditional metals such as Ni and Co, but also many non-traditional metals (e.g., REY). Many of these elements are known to be highly enriched in deep-sea ferromanganese (Fe-Mn) nodules and crusts. However, unlocking these metals from their deposits through metal processing is – aside from deposit exploration and production – expected to be a critical component that will affect the overall economics of the marine mining value chain. Hence, research and development of tailored metal processing solutions which can target specific metals of interest in Fe-Mn nodules and crusts, is required. Dynamic mineral recrystallization (DMR) of Fe-Mn oxide phases is a geochemical process that may have notable potential for hydrometallurgical applications. We have recently demonstrated that Ni can effectively be cycled between deep-sea Fe-Mn nodules and crusts and solutions through dynamic mineral recrystallization. DMR occurs in nature as abiotic background process during biogeochemical Mn cycling when dissolved Mn(II) is in direct contact with Mn oxides. Trace metals which are incorporated in the Mn host phases, are cycled between solid phase and solution via coupled dissolution (trace metal release) – reprecipitation (trace metal incorporation) mechanisms.

Jan 1, 2018

By Samantha Whisman, James R. Hein

Hydrothermal marine manganese-oxide deposits (HMMD) are cemented and variously replaced volcaniclastic and biogenic sediments that were mineralized by distal, low- temperature, hydrothermal fluids. HMMD predominantly form below the seabed as sediment-hosted statabound deposits but can also form on the seabed. These deposits form at oceanic and back-arc basin spreading centers, volcanic arcs, and mid-place hotspot volcanoes. HMMD have traditionally not been considered to have an economic potential because they were considered to be devoid of economically valuable critical elements. This contrasts with their non-hydrothermal counterparts, ferromanganese crusts and nodules, which are enriched in many critical elements. However, manganese is now one of the critical metals and HMMD have the highest manganese contents (up to 55% Mn, so- called battery-grade Mn) of all the types of deep-ocean mineral deposits. There is a growing demand for this critical metal and an upward trend exists in the price of manganese on the global market. Also, other critical elements can occur in high concentrations in some HMMD and their economic potential has not been considered, especially for lithium (up to 0.17%) and molybdenum (up to 0.24%), but also vanadium (to 820 ppm), chromium (to 346 ppm), and nickel (to 0.45%), among others. Which of these critical elements are enriched and their concentrations depend on the types of rocks leached at depth by the hydrothermal fluids, the composition of hydrothermal minerals precipitated in the higher temperature parts of the circulation system, and the types of sediments mineralized by the manganese oxides. For example, mineralization of a carbonate sediment resulted in the highest lithium contents, whereas leaching of ultramafic rocks at depth as a rule results in the highest chromium and nickel contents in the HMMD. These deposits are known to be widespread, especially in volcanic arcs, but their lateral and vertical extents and consequently size, tonnage, and grade have not been determined. Most samples of hydrothermal deposits have been collected by dredging and therefore the in situ relationships often are not known. One sample from the Mariana volcanic arc, west Pacific, was collected by ROV at 1274 m water depth from a layered outcrop 6.6 m thick that may be a sequence of pervasively mineralized volcaniclastic layers and offers the first clue as to the potential vertical extent that these deposits may attain. However, only the top ~0.4 m-thick layer was sampled, so it is not known whether the mineralization extents throughout the outcrop. Although large manganese deposits of various origins occur on the continents, they consist of manganese carbonates, silicates, or complex mixtures of manganese minerals. In contrast, marine hydrothermal HMMD exhibit relatively simple mineralogy that would make processing of this potential ore much simpler.

Jan 1, 2018

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011

By James R. Hein

A new data set of cobalt-rich ferromanganese (Fe-Mn) crust chemistry has been completed for the first detailed sampling of a latitudinal crossing of the Pacific equatorial zone of high biological productivity. Samples were collected in January-March, 1999, during the AVON 2 cruise aboard the R.V. Melville, Scripps Institute of Oceanography. Samples were collected from 4.6° N to 9.2° S latitudes along two ridges, the Marshall Islands-Gilbert Islands ridge (4.6° N to 3.5° S) and the Howland Island-Tokelau Islands ridge (1° N to 9.2° S). The two ridges are offset east-west in the region of overlapping latitudinal sampling by about 466 km. We determined the concentrations of 48 elements for 147 samples from 39 dredge hauls taken on 33 seamounts and island flanks that occur between the Marshall Islands to the northwest and Samoa to the southeast. Element concentrations can be examined as varying spatially and with water depth in the ocean and we examine those relationships based on statistical analysis of the chemical and spatial data. The mean Fe/Mn ratio of 1 and mean Co content of 4645 ppm are typical of West Pacific hydrogenetic crusts; but the mean Co content is low compared to those of some equatorial North Pacific sites, such as the Marshall Islands and Johnston Island EEZs. In contrast, the mean Cu concentration (1540 ppm) is 35% higher than the mean concentration for Pacific Ocean Fe-Mn crusts (998 ppm). Another striking difference is the 40% higher Ba concentrations (mean 3107 ppm) compared to typical Central and West Pacific crusts (mean 1876 ppm); but Ba concentrations are lower than those in California continental-margin Fe-Mn crusts (mean 4085 ppm). A final significant difference in Fe-Mn crust chemistry is Zr concentrations, mean 921 ppm (maximum 1523 ppm), which is about 30% higher in this data set compared to the previously determined mean value of 613 ppm for Central and West Pacific crusts. Zirconium has a strong positive correlation with Ba and a weak positive correlation with Mn.

Jan 1, 2003

By Andrew Bellamy

A thorough appreciation of the origin, formation, preservation and geometry of marine sand and gravel deposits is central in demonstrating that their extraction by dredging does not affect coastal processes or marine life. Geological evaluation underpins wave, tidal and sediment transport modeling and assists in predicting the nature and extent of seabed change during and after dredging. Marine sand and gravel deposits in the English Channel, southern North Sea and parts of the Irish Sea are of predominantly periglacial fluvial origin and record long histories of valley and floodplain cut and fill associated with Quaternary climatic and sea level oscillations. In the Bristol Channel, the influence of marine transgression and tidal dominance in sorting proglacial outwash deposits is evident in the distribution of sandbanks, scoured channels and gravel lags of this region. These deposits are relict and are unrelated to coastal sediment dynamics. Their extraction leaves seabed depressions which monitoring shows remain unfilled. The resultant offshore bathymetric changes and sediment removal in over 10 m water depth are not transmitted to the coastal zone as beach drawdown, wave height increases or sediment starvation. Applications for new aggregate dredging permissions in UK waters must be accompanied by an EIA and need to make a convincing case that the dredging will not affect rare or declining species and communities of marine life. Seabed recovery rates post dredging are now investigated and understood with reference to geological setting and the uniqueness of the sediment/biological character (biotope). Investigation of the continental shelf by the Industry and others reveals the large extent of gravel-dominated biotopes relative to commercially viable deposits.

Jan 1, 2004

By James R. Herring

An unusual combination of ten new, deep (-100 m) coreholes and an extensive high-resolution seismic reflection network enables us to produce a detailed study of the phosphorite resources in the Tertiary strata of the Georgia continental shelf. These strata are mixtures of a terrigenous facies, notably quartz and clay along with minor amounts of other aluminosilicate minerals, and of a marine facies, notably phosphorite and carbonate. Phosphatic sediments occur throughout the cores, however the richest phosphorite beds are in the middle Miocene (Serravallian) sediment, where they constitute up to 70 percent of the sediment mass. Major zones of phosphate enrichment occur chiefly at major unconformity boundaries (tops of Oligocene, lower and middle Miocene, upper Miocene, and lower and upper Pliocene) and at prominent intrastratal reflectors representing minor unconformities within units. Phosphorite co-occurs with the clay minerals, especially palygorskite, but correlates inversely with carbonate and detrital quartz, indicating a low-energy depositional environment. The clay minerals present in these strata, which have an environmental consequence on recovery of the phosphorite, are varying concentrations of smectite, kaolinite, mica, palygorskite, and sepiolite. Phosphatic resources have been determined within only the Miocene strata. Sediment volume for this unit to the 100 m isobath on the continental shelf has been established using the high-resolution seismic reflection network that has been calibrated using the deep coreholes. Phosphorite grains larger than 0.1 mm average about 40% of the sediment. In turn, most of the remainder of the sediment in this size range is quartz, which is separable from phosphate grains using conventional flotation techniques. Our estimate is that 300 Gt of phosphorite lie within the Miocene strata of the Georgia continental shelf.

Jan 1, 1994

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993