Search Documents

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By M. E. Moraes Castanho de Almeida, A. Ribeiro Cotri

Recovery of cobalt to produce high grade cobalt sulfate from cobalt concentrate by leaching and solvent extraction was investigated. The PLS typically contains Co 10g/l, Mg 2g/l, Fe < 10ppm, Mn < 200ppm, insolubles <100ppm and is extracted with 20wt% Cyanex??272. The typical strip solution contains Co 60g/l, Mg 0.03g/l, and was sent to the current process for the production of cobalt sulfate heptahydrate. The cobalt yield of the plant with two extraction steps was 92%, with three steps was 97% and with four steps 99%. The extraction stage used the concept of "scrubbing" in a countercurrent system. In the first stage of extraction pH was 4.8, and in the last stage of extraction pH 5.5 to promote the exchange of magnesium in the organic with cobalt contained in the PLS. Following the extraction, when using two scrubbing stages, Co/Mg selectivity between of 2,000-3,000 was obtained, and with three scrubbing stages, selectivity was greater than 6,000. The desired selectivity was reached when using a scrubbing configuration with O/A ratio of 10:1. The typical cobalt sulfate heptahydrate had the following composition: Co 20wt%, Mg < 0.01wt%, Fe < 5ppm, Mn < 0.01wt%, Cu < 0.01wt%, Zn < 0.01wt%.

Jan 1, 2014

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By W. D. Bonisteel

In 1976, Rio Algom Limited began the expansion of uranium production facilities at Elliot Lake. Quirke Mine was the only property in operation at the time, and plans were made to expand its milling capacity from 4,500 to 7,000 tons of ore per day. Following this expansion, other properties in the area will be reactivated to fulfill long-term contracts for uranium. As part of the expansion program, it was decided that in view of the escalating cost and impending shortage of energy, heat reclaim and conservation would be employed wherever practicable. In general terms, heat reclaim applications fall into three main classifications: ventilation, utility and process. Two of the ventilation applications and one process application will be described in some detail. Several other systems will be presented briefly as a matter of general interest. Some future possibilities will also be mentioned, together with their potential for economical heat recovery.

Jan 1, 1979

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter&apos;s requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By Rita Awwad

Building Information Modeling (BIM) has been gaining a significant edge in the construction industry over the last decade. BIM allows gathering all building information in one shared database that can help all construction entities better understand, integrate and visualize all work progress from inception to operation of the building. The main purpose behind BIM is to bring all project participants together (Client, Architect, Contractor, Consultant) since the initial stages of a project allowing them to cooperate and work as a team in the promise of an increased productivity, reduced cost, enhanced quality and faster delivery. However, a full-fledged implementation of BIM tools and benefits is not yet achieved in the construction industry and remains a debatable issue for researchers and practitioners in the construction field. This paper aims at assessing BIM awareness and usage in the Lebanese construction industry through conducting interviews with contractors, architects and consultants that are key players in the Lebanese market. A comprehensive literature review about BIM adoption in some developed countries and in the surrounding region is also provided in order to better evaluate the Lebanese industry status in comparison with foreign industries. This research sheds the light on BIM awareness of the different construction parties in the Lebanese market, assesses the extent of its current use, identifies the pertaining implementation challenges, and provides recommendations to enhance BIM role in the Lebanese construction industry.

Aug 1, 2013

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

By Andrew J. Troop

"VAUGHAN THOMPSON designed the Thompson retrievable diamond drill wedge and reaming assembly in 1948. Since 1950, the Hudson Bay Exploration and Development Company, Limited has used the method extensively. The wedge, setting tool, and reamer have been modified slightly since they were first introduced. In 1951, Mr. Thompson designed the Thompson arc cutter. The purpose of this tool is to decrease effectively the diameter of the arc cut, using standard drilling tools. This directional drilling device is usually employed when a branch hole is desired. The Thompson arc cutter has been used with success at Birch Lake, Saskatchewan, at the property of Cuprus Mines, Limited, Manitoba, and at Thompson Lake, Manitoba.UsesThe Thompson retrievable wedge provides a simple method for:(1) Re-drilling lost core sections(2) Re-sampling sections of old holes(3) By-passing lost tools Correcting the direction of a hole(4) Drilling a branch hole to obtain intersections at a higher elevation than the original holePrevious to the spring of 1951, the wedge was used only for the first four of these purposes. Recently it has been employed extensively for drilling branch holes."

Jan 1, 1953

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By H. P. Whaley

This paper introduces Wabush Mines, including its ownership, physical assets, capacity, goals and achievements. It is to be followed by four papers which will present the detailed story. Wabush Mines, the largest supplier of iron ore to the Canadian steel industry, was brought into production in 1965. The ore is mined and concentrated in Wabush, Labrador, Newfoundland and pelletized at Pte. Noire, Quebec. Annual capacity is over 6,000,000 tons of high-grade iron ore pellets.

Jan 1, 1969

By D. Ofstie, B. Kargutkar

BIM, or Building Information Modeling, is transforming the way metallurgical facilities are built, operated and maintained. BIM provides a digital representation of the facility, complete with all physical and functional characteristics - enabling collaborative planning, concurrent design, construction simulation, sustainable operations and predictive maintenance through a connected information model. Building on experience gained in other industries, Hatch is aggressively applying the BIM process to the mining & minerals processing industry to address inefficiencies inherent in traditional document-based information management. Intelligent 3D models support real-time quantity forecasting and cost trending by commodity type and construction work package. By linking procurement and schedule data, material availability and constructability reviews are visualized to verify construction critical path, ensure work front safety and minimize craft downtime. The BIM digital information model connects engineering, construction, commissioning and vendor data, aiding timely asset-centric handover to plant operating and maintenance systems.

Jan 1, 2015

By J. Mizera, J. Zdunek, K. J. Kurzydlowski, A. Dobkowska

This work concerns comparison of corrosion resistance of the aircraft aluminum alloy composed of Al - 2.3%Li - 0.1% Zr. The alloy was hot rolled (HR) from 13 mm to a thickness of 4 mm (e = 2.4) and 1 mm (e = 5.2). Corrosion resistance was investigated by Potentiodynamic Polarization Test. The investigation relied on exposure samples in two different corroding medium: 0.5 M NaCl solution and 0.01 M Na2SO4 solution with added 0.01% of Cl- at room temperature. Furthermore, the microstructure was analyzed using the optical microscope with polarized beam. The hardness was measured on lengthwise profile. It was stated that alloy after the largest deformation (equivalent total strain e = 5.2) is characterized by the best mechanical properties and the best corrosion resistance. The alloys in initial state and after deformation to 4 mm (e = 2.4) are characterized by worse corrosion resistance. It is associated with microstructure and density of dislocation in analyzing material.

Jan 1, 2015