Search Documents

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By P. W. A Severin

"The Sturgeon Lake deposit, a partly eroded lens of massive sulphides with an underlying sulphide stringer zone, is one of five orebodies that occur in the Sturgeon Lake area of northwestern Ontario within volcaniclastic rocks of the Archean Wabigoon Subprovince in the Superior Province of the Canadian Shield.The Sturgeon Lake Cu-Zn-Pb-A g-Au deposit was discovered in October 1970 as a result of an I.P. survey. Production from this open-pit mine began in March 1974 and continued until the ore was exhausted in March 1980.The Sturgeon Lake property is underlain by basaltic volcanics, minor amounts of mafic lapilli tuff and rhyolite volcaniclastics. A quartz crystal-bearing rhyolite occurs at the top of the felsic volcaniclastics and is ""capped"" by the Sturgeon Lake massive sulphide deposit. The felsic volcanics have been intruded by a crudely layered sill-like, carbonatized mafic intrusion. Recent work suggests that the felsic rocks that underlie the Sturgeon Lake deposit are lateral equivalents of those in the vicinity of the Mattabi Mine and are not correlative with the dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits. Hydrothermal processes that resulted in the formation of the Sturgeon Lake orebody have resulted in a depletion of Na2O, CaO and FeO and an increase in MgO, K2O, copper and zinc. In the vicinity of the sulphide stringer zone, the rhyolites are ""bleached"" due to silicification and sericitization. The rocks lying immediately below the massive sulphides are locally strongly chloritic.The Sturgeon Lake deposit may have formed on a top ographic high which prevented mafic flows and dacitic volcaniclastics that underlie the Lyon Lake and Creek Zone deposits from inundating the Sturgeon Lake fumarolic vent from the west. Continued or resurgent activity from the Sturgeon Lake fumarole may have resulted in the formation of the Lyon Lake and Creek Zones as more ""distal "" deposits in topographic lows. The Sturgeon Lake, Lyon Lake and Creek Zone deposits were subsequently overlain by mafic tuffs and flows."

Jan 1, 1982

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By P. Cleyle, J. H. Masliyah, R. S. Chow, Z. H. Xu, Z. A. Zhou

Bubble nucleation in water under dynamic conditions was investigated using an autoclave at an air saturation pressure of 7 atm. Agitation during air saturation of water was found to be crucial in enhancing tiny bubble formation. More bubbles nucleated on hydrophobic surfaces at a higher agitation rate, due to cavity formation by the more intense hydrodynamic conditions. Flotation recovery of bitumen from oil sands demonstrated a significant role of bubbles nucleated in water: more than 50-170% increase in bitumen recovery from different oil sands was obtained by using air supersaturated than the regular water.

Jan 1, 2009

By Paul Guliov

Coal-bearing Tertiary sediments of the Ravenscrag Formation in southern Saskatchewan host numerous deposits of clinker resulting from in situ coal combustion. Clinker deposits form when sediments of relatively low temperature firing properties overlie coal seams which are undergoing prolonged spontaneous combustion. The resulting fired material is useful for decorative landscaping aggregate, rock gardens, driveways, mud control and others. Predicting the occurrence of clinker deposits requires a knowledge of the spatial distribution of coal seams and the nature ofoverlying sediments. Knowledge ofpaleotopography at the time of coal combustion can assist in locating more highly-fused material which can yield greater block sizes. Coal data bases can be used as a predictive tool by outlining areas where coal is or was at or near surface and therefore may have been susceptible to spontaneous combustion.

Jan 1, 2001

By M. Okada

Consumption of refined copper in Asia, especially in China and India, has soared, and the copper price is at its historic height. New smelters and refineries have been built in the region with state-of-the-art technology to meet the unprecedented demands. Supply of copper concentrate, on the other hand, has fallen short of the growing demand for concentrate by the smelters and refineries with expanded production capacities. The shortage of copper concentrate is attributable to the delay in the mining development, caused by the prolonged price slump of before 2005. The mismatch between supply of concentrate and smelting and refining capacities may cause disorderly movement of copper price, and hamper the sound development of the industry. The recent high copper price may prompt substitution with alternate materials. With electrical and thermal conductivity and workability, copper is one of the most customer-friendly materials. It is regrettable for both customers and suppliers if the high copper price would become an impediment to promoting copper use. Some outdated and environmentally unfriendly facilities still operate. In view of recent lower-grade copper concentrate with higher sulfur content, these facilities must reform their equipment to environmental-responsive one. The current level of per capita consumption of refined copper in Asia shows that the demand of copper will further grow. It is necessary to realize stable supply of refined copper and stable copper price, to help developing countries including China and India to economically take off. Hence, it is essential that the development of the copper industry be accompanied by environmentally friendly facilities, and harmoniously increased capacities between mining and smelting and refining.

Jan 1, 2007

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to 'Iron Ore in 1954', involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company's current mining practices.

Jan 1, 1958

By Andrew Young

A Question Murray Dodge ?Inco Stobie Maintenance ?I visually inspect my hoist ropes every day and seldom find anything. Is there a better way to do the inspection?? Based on HRIA research activities, the answer would seem to be ?yes?.

May 1, 2006

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007