Search Documents

By W. A. Jankola

Teck Cominco Metals Ltd. operates an integrated zinc-lead smelter at Trail, British Columbia, Canada. The zinc circuit comprises three parallel operations: conventional fluid-bed roasting, direct zinc pressure leaching of concentrates and atmospheric leaching of zinc oxide fume recycled from the lead smelter. The products from these three areas are combined in the main leaching plant where they undergo iron purification. Unlike most leaching circuits, the leach process in Trail begins with an acid leach and is followed by a neutral leach. An evaluation was undertaken to determine if the process at Trail could be improved by converting to the conventional neutral leaching process with a subsequent acid leach of the residues. This paper explores the results of these tests and the implications for Trail Operations.

Jan 1, 2006

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By T. V. Simpkinson

Abstract A brief history of the electric arc furnace process of steel-making is given. The greater relative importance of this method of steel manufacture to the Canadian steel industry, as compared with its importance in the steel industry of the United States, is shown. The scope of the process is outlined and brief mention is made of the difficulty of obtaining melting stock low in alloy content. The physical chemistry of steel-making is discussed at length in simple terms, with emphasis on oxidation, de-oxidation, and the role of hydrogen. Carbide-type and silicon-type slags are described and the particular usefulness of each is outlined. The importance of various factors in the melting practice is evaluated on the basis of practical experience. Introduction Although electric furnace steels constitute only a small portion of the total weight of steel used in industrial operations, their importance is relatively much greater than is indicated by comparative tonnage figures. Tool steels, which are vital to all industry, are made almost exclusively by the basic electric arc furnace process, as are stainless steels, valve steels, and the higher alloy types of the class usually referred to as "alloy steels'. For many applications where steel other than electric furnace quality is often used, and when first cost is secondary to performance in service, the extra steel cost of electric furnace quality material is usually returned with interest by consistently longer service life. The electric furnace is pre-eminent in the quality alloy steel field because of the control that may be exercised over conditions of oxidation, de-oxidation, and temperature, the fundamental operations in steel making.

Jan 1, 1948

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By E. J. Debicki

"At the 1992 PDAC Convention, Norman Keevil announced the formation of the Exploration Technology Division (ETD) of the Mining Industry Technology Council of Canada (MITEC). It was evident that base metal reserves in Canada were declining and that the cost of discovering a deposit in Canada was increasing. Coordinated research to develop new exploration technologies was required to discover the next generation of ore-bodies. The ETD was formed in response.The mission of the ETD is to contribute to the survival, profit, and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral exploration through development of innovative technology by man-aging and coordinating applied cooperative research. In addition, it is the intent of the ETD to become the principal agency by which cooperative research funds are transferred to researchers from the mining industry. The division is industry driven, industry funded and industry managed.The ETD’s Three-Year Plan has focussed80% of its research funds toward two objectives, improving the efficiency of exploration for VMS deposits and establishing the parameters necessary to discover the next Hemlo deposit. The remaining 20% is allocated to other projects, with the current emphasis on geophysics.In 1995, corporate members total twenty-three major mining companies accounting for90% of the exploration expenditures in Canada. The ETD is currently managing ten cooperative research projects totalling $4.6million. Other projects, estimated at $1.6 mil-lion, are currently under development."

Jan 1, 1996

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By Robert B. Parsons

"Canadian income tax legislation contains a number of provisions which serve to facilitate the structuring of business arrangements, including mineral resource ventures. These rules are often fairly complex and not easily understood. This article attempts to explain in plain and understandable language the mechanics and benefits of one of the more frequently encountered provisions, the ""Section 85 election"".IntroductionThe Canadian resource industries are probably singled out for more special attention under this country's tax legislation than any other industry. This special treatment is, of course, not always welcomed by the industry, such as where unnecessarily restrictive taxation is perceived to exist or where agonizingly complex tax legislation must be dealt with. On the other hand, certain provisions in the tax legislation treat the industry in a relatively favourable manner, including a number of rules which, in recognition of the high risk and capital requirements of the resource sector, serve to facilitate the structuring of resource ventures."

Jan 1, 1984

By H. Qi, J. L. Feng, D. J. Li

"In the present paper, the characteristics of the granite burst under loading/unloading conditions was studied by means of both laboratory experiment and finite-discrete element method (FDEM). After gaining the mechanical properties of the granite samples under uniaxial compression conditions, the parameters taken as input arguments in the FDEM modelling were then carefully calibrated so as to provide some basic data including Young’s modulus, Poisson’s ratio, uniaxial strength, Lame constants, cohesive strength, and frictional angle for further being used in simulating granite bursts. All the simulating results by the FDEM were basically in agreement with that obtained from the uniaxial compression test and triaxial granite bursts in laboratory, respectively. This study shows that that such computational mechanics of discontinua can be employed to gain powerful insight into the failure mechanism of granite burst, which could also be a useful tool to clarify the collapse mechanism of rock structures in rock engineering design and rock test scheme optimisation. INTRODUCTIONBased on discontinuum state a priori, discontinuous modeling techniques that are commonly referred to as discrete element methods (DEM) treat the material directly as an assembly of separate blocks or particles, which was originally proposed by Cundall (1971) and Cundall and Strack (1979) from the viewpoint of analogous molecular dynamics simulation to better account for and understand the interaction between the blocks. The distinct feature of these formulations is that a constantly changing problem of geometry and contact conditions can be addressed by solving the equations of motion using an explicit time marching scheme (most often in a ‘leap-frog’ format), while updating contact force histories as a consequence of contacts between different discrete elements and/or resulting from contacts with model boundaries (Bicanic 1998). The most notable implementations of DEMs are arguably represented by the universal distinct element code (UDEC) (Itasca Consulting Group Inc., 2013) and the particle flow code (PFC) (Itasca Consulting Group Inc., 2012). Another formulation is the discrete crack framework that is based upon some criteria for an advancement of crack front, which is coupled with extensive local and global re-meshing while simulating by numerical methods such as finite element technique, commonly using fracture theories. Certainly, it is relatively easy to trace the propagation of single crack front governed by some principles of energy release rates (Ingraffea 1997) but tracing of multiple cracks leads to topological and algorithmic complexities. Otherwise, there is no consideration of interacting cracks in these formulations of finite element or enhanced finite element techniques (e.g., in XFEM and ABAQUS)."

Jan 1, 2015

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930

By G. Van Weert, O. Wang

"As part of a general review of processing double refractory ores through Barrick Gold’s autoclaves / CIL facility at Goldstrike, blanking the preg robbing native carbon in the process solids with hard (m.p. 55 - 60 º C) paraffin wax was studied, specifically in relation to pressure oxidation. The improvement in CIL gold extraction was found to depend on the wax addition point, with hot, dry contacting of the ore in the presence of wax - prior to POX - yielding the largest, most consistent improvement in gold extraction.INTRODUCTIONDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including Carlin Trend, NV, deposits, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (Thomas, 1994). It is the latter route to which this paper refers.The second barrier refers to the actual gold recovery. Gold may be extracted from the pressure oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This is taken advantage of on a large scale by gold millers, who use manmade activated, i.e., graphitized carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold cyanide bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold. The second barrier becomes problematic when the ore naturally contains graphitic orcarbonaceous material, hereafter referred to as native carbon (versus the man-made activated carbon). This material may also adsorb gold cyanide in competition with the activated carbon. Since the native carbon is ground with the ore it is much smaller than the activated carbon. Any competition between the two carbons may produce a loss of gold from the pregnant leach liquor to the process tailings. This phenomenon is called “preg robbing”. Goldstrike ores come from the Carlin trend, which is known for the occurrence of native carbon (Adams & Burger, 1998; Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001; Tretbar, 2004)."

Jan 1, 2012

By V Dolmage

In 1957 and 1958, ten topographically suitable damsites were investigated along the Peace river between Finlay Forks and Hudson Hope, B.C. Of these, three were eliminated after a reconnaissance survey indicated that the geology was unsuitable for the 650-ft.-high dam contemplated. ?After extensive drilling, five other sites were deemed unfeasible because of geological factors and, in 1959, the two remaining sites were designated as being suitable, one for the high dam and the other for a low dam downstream. The sites are located in the Peace River canyon, on the west and the south? side of Portage mountain, west of Hudson Hope. The site for the large dam, the Portage Mountain dam, has since been investigated by surface mapping, thousands of feet of diamond drilling, a seismic survey, laboratory rock tests and on-site grouting tests in order to establish the possible effect on the dam of all facets of the foundation rocks. Three diversion tunnels, 50 ft. in diameter and 2,200 feet in length, have been driven through massive sandstone and shale, and an intake cut, 500 ft. in length, 200 feet in width and 200 feet in depth, has also been excavated in rock.

Jan 1, 1963

By F. Liu, H. A. Meier, D. M. Valiveti, P. A. Gordon

Hydraulic fracture is a frequently used technique in the Oil and Gas industry to create high permeability pathways for extraction of hydrocarbons. Numerical simulation of this method poses challenges such as representation of 3D fractures, propagation of randomly oriented fractures in 3D media, enabling fluid leak-off from fracture to poro-elastic medium. We have developed a numerical model using the Generalized Finite Element Method (GFEM) to simulate fluid driven fracture in a poro-elastic medium that addresses these challenges. In the GFEM framework, special enrichment functions are used to augment the solution space in the displacement and pore-pressure fields in order to accurately capture the response in the vicinity of the fracture. Adaptive refinement of the finite element mesh is also employed to facilitate accurate and efficient solution of the model. Our model fully couples fluid flow in the fracture, represented with the lubrication approximation, to the geo-mechanical behavior of the bulk poroelastic rock, comprised of an elastic rock skeleton saturated with fluid. Fracturing fluid exerts traction on the fracture surface and is also allowed to leak-off into the poroelastic medium using a transfer function approach. Stress intensity factors (SIFs) are evaluated based on the Contour Integral Method, accounting for the fluid pressure on the fracture surface. The SIFs are used to govern a full 3-D evolution of the fracture. Verification of the model is performed for known behaviors for the poroelastic response and fluid flow in the fracture.

Jan 1, 2015

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By R. Drozd

"The Bullmoose Mine is currently under construction in the North East Coal area of British Columbia, and approximately $300 million will be spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by December 1, 1983.The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-Iwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project.This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, construction progress, approvals and permits, and general financial arrangements.IntroductionThe Bullmoose Mine Project"" is located about 87 road kilometres south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 road km to the east.The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high quality, medium volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of 0.6 mty will be thermal coal production.Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine will commence. The plant should be fully operational by December 1983, and first vessel loading at the Ridley Island port is scheduled for January 1984."

Jan 1, 1983

By D. R. Lentz, C. J. Beaumont-Smith, S. H. Mcclenaghan

"Abstract - The Louvicourt Au-Ag-Cu-Zn-Pb sulfide deposit is hosted by a Middle Ordovician calc-alkaline sequence of aphyric rhyolite flows and associated fragmental rocks at the top of the Flat Landing Brook Formation. The Zr/TiO2 (average = 0.110) and Y/TiO2 (average = 0.021) ratios in the footwall felsic volcanic rocks are consistent with known values for the Reids Brook member. The deposit consists of two concordant lenses of semi-massive to massive sulfides, approximately 150 m long and up to 9 m thick, which represent a fold repetition of a single exhalative horizon. The deposit contains a geologic resource of 136 000 tonnes grading 1.2% Pb, 1.0% Zn, 0.4% Cu, 90.9 g/t Ag, and 0.96 g/t Au; the deposit locally contains elevated Au (2.9 ppm) and Ag (320 ppm) contents. A laterally continuous iron formation that contains barite caps the deposit, and is gradational vertically and laterally into laminated siltstone. The exhalite confirms the stratiform nature of this deposit, but a large percentage of sulfides occur as late replacements of altered felsic fragmental rocks in the footwall. Abundant examples of colloform pyrite and perlitic and spherulitic textures in volcanic clasts are well preserved. The base- and precious-metal content of the Louvicourt deposit is atypical of the Bathurst Mining Camp (BMC). Reported assay data (n = 27) indicate an average Pb/Zn ratio of 2.6, the highest in the BMC (average = 0.39). Lead exhibits a strong Spearman Rank correlation (r' = 0.92) with base metals throughout the sequence, indicating a preponderance of galena in both the stockwork and stratiform zones. The Ag and Au contents in this deposit are among the highest in the BMC and exhibit a Au-Ag- Cu-Pb association. Barite-rich exhalative pyrite exhibits a moderate Au correlation with Ag (r' = 0.77; n = 10) and Cu (r' = 0.76) and occurs in portions of the exhalative sulfides that are enriched in Pb. Chemical exhalative rocks are conformably overlain by trachy-andesitic volcaniclastic (possibly pyroclastic) rocks that are assigned to the Little River Formation. These are enriched in Nb (average = 38.4 ppm) and P2O5 (average = 0.17 wt.%), and have much lower Zr/TiO2 (average = 0.056) and Y/TiO2 (average = 0.0062) relative to rocks higher in the hanging wall. The intermediate volcanic rocks are conformably overlain by massive to pillowed basalt flows and related hyaloclastite that have Nb/Y = 0.60 and high TiO2 contents (average = 2.8 wt.%). This chemistry is consistent with rocks of the Brunswick Mines member (Little River Formation), except that these rocks are considerably enriched in P2O5 (average = 0.82 wt.%). This syngenetic exhalative deposit is unique for the BMC with a high Pb/Zn and elevated Au and Ag contents, as well as an epithermal signature (Sb-Ag-Au-Tl-Hg), analogous to high sulfidation volcanogenic massive sulfide deposits. Its intimate relationship with an emergent felsic dome (Flat Landing Brook Formation), chlorite-silicate-oxide-sulfide exhalite (locally hematitic), and the abundance of barite are classical features of many of the Kuroko deposits."

Jan 1, 2006

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d'un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu'avec l'Argentine, l'autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l'un des pays les plus pauvres du continent. Ce paradoxe n'est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d'une tradition minière de plus de quatre siècles et d'un potentiel géologique indiscutable ayant conduit à la découverte et à l'exploitation de fabuleux gisements d'argent et d'étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n'a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By Andrew Matyas

"During the summer of 1968, the author was employed in the Research Department of Dominion Foundries and Steel, Limited, Hamilton, Ontario. Over the years, Dofasco has been conducting a program for developing more efficient control of its basic oxygen steelmaking process. The author was thus able to obtain a variety of viewpoints from both research engineers and furnace operators. He also had access to extensive literature dealing with BOF control schemes underway at other major steel producers. This paper describes the present state of developments in BOF steelmaking control.The necessity for efficient BOF control is pointed out. To appreciate the variables to be controlled, a brief outline of process fundamentals is included. Technical aspects of present methods of practical control are examined in detail; the relative merits of dynamic over static control models are emphasized. Finally, it is shown how an effective dymic-optimizing control scheme serves as the basis for closed-loop computer control of the process."

Jan 1, 1970