Search Documents

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d'asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l'amiante peut offrir les performances souhaitées et l'augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d'une faible teneur en amiante courte il l'enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C'est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu'on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

A recovery process for rare earths (REs) such as dysprosium and neodymium from the leach liquor of permanent magnet scrap (PMS) was developed. The two hydrometallurgical routes namely liquid-liquid extraction (solvent extraction) and selective stripping were implemented. The present study deals with the separation and recovery process development by using organo-phosphorous based extractant di-(2-ethylhexyl phosphoric acid (D2EHPA) as reagent for REs processing. Initial studies considered the influence of time on the extraction process, as well as pH and extractant concentration effects. This suggested the aqueous mechanism and separation factors played a role in process during development. McCabe-Thiele diagrams for extraction isotherms were developed. Counter current extraction (CCE) using various phase ratios influenced metals separation. Maximum loading capacity of the D2EHPA was determined. The loaded organic generated by the CCE process was water washed followed by a scrubbing process to remove the other metal ion from targeted metal. Finally, a stripping process was tested using various mineral acids.

Jan 1, 2015

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By Gary Raymond

The Similkameen Division of Newmont Mines Limited operates a low-grade open-pit copper mine in southern British Columbia. The copper mineralization is extremely erratic.As a result, over seven years of operation, ore control methods have evolved from standard flagging based on blast-hole assays, through an in-pit grab sampling system, to the present method of mining to computer-determined ore-waste boundaries based on geostatistics. These improved ore control methods have resulted in a gain of at least 25% on ore tonnage miffed, at the same grade as obtained using earlier techniques. At the same time, geostatistical ore reserve estimates are now within 7% of milled ore tonnage and grade on a yearly basis, whereas the original polygon ore reserves under-estimated mineable ore tonnage by 15% to 45% and over-estimated grade by about 20%. The author discusses why traditional ore estimation methods give poor results in erratically mineralized orebodies and describes the geostatistical approach to the problem.

Jan 1, 1979

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By Sabry A. Sabour

Metal price is among the key variables in the open pit optimization and the economic evaluation process. The common approach to handle metal prices in open pit mine planning is to optimize the ultimate pit and the mining schedules using a fixed, flat metal price. In this respect, metal price is assumed to be known with certainty throughout the entire mine life, which in some cases can reach 80 years. Given the volatile nature of metal markets and the metal price cycles, the conventional pit optimization approach may generate sub-optimized mining plans, which results in either extra costs to mining projects or lost revenues, or both. Long-term operational decisions such as future pit expansions, beyond the currently optimized limits, cannot be handled using the pit optimization approach based on flat metal prices. There is a growing interest in the mining industry to model and manage such market uncertainty in the pit optimization as well as the project evaluations in order to maximize the value of mining operations. In this paper, the author will outline a practical approach to optimize the ultimate pit taking into account the volatility and variability of metal markets. The proposed approach uses a combination of the pit optimizer of the commercial MineSight package and a simulation-based economic modeling real options valuation approach employing the least-squares Monte Carlo algorithm. MineSight pit optimizer employs both the floating cone for initial optimization exercise and the standard Lerchs-Grossmann algorithm. In this paper, Lerchs-Grossmann option will be used to generate the pit shells. Real options valuation approach used in this study is based on generating multiple metal price scenarios. Metal price uncertainty is modeled using stochastic metal price models such as the geometric Brownian motion and the mean-reverting process. The mining operational scenarios corresponding to the simulated metal prices are then optimized using the least-square Monte Carlo approach. The objective is to maximize the discounted cash flow value of the project while incorporating the operating flexibility to revise the operating status of the open pit with time as new information becomes available. The focus of this work is on the practicality of the proposed uncertainty-based pit optimization approach and the difference it can make to the technical operational mining decisions. A case study of a hypothetical open pit poly-metallic mine is provided. The deposit contains copper, gold and silver grades. The run of mine ore is sent to the process plant that produces copper concentrate with copper as the main metal and gold and silver as the by-products. Four uncertain variables are considered here include copper, gold, silver prices and foreign exchange rate. Both copper price and exchange rate are modeled using the mean-reverting process while gold and silver prices are modeled using the geometric Brownian motion. The case study is performed using both the conventional flat price pit optimization approach and the proposed uncertainty-based one to compare results.

Aug 1, 2013

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By Eldon L. Brown

Location and History The Sherritt Gordon property is located in northwestern Manitoba, about 100 miles north of The Pas and 40 miles northeast of Flin Flon. It is connected with the Manitoba Northern railway, which runs from The Pas to Flin Flon by a branch line, 42 miles in length. The location of the property is shown on the sketch-map, Figure 2. The ore deposit was first discovered by Philip Sherlett, a Cree Indian, in 1922. In 1924 Sherlett's claims lapsed and the ground was re-staked by Carl Sherritt and Dick Madole, and was optioned by them to J. P. Gordon in the summer of 1925. Gordon re-optioned the property successively to three well-known mining groups, one of which did some surface trenching .and put down 28 shallow diamond-drill holes before dropping their option. In the latter part of 1927, a Company known as Sherritt Gordon Mines, Limited, was formed to take over the property, and preparations were made for systematic development work. Preliminary Development In order to fill-in gaps left by the original drilling, a light diamond-drill outfit was flown-in to the property from the Hudson Bay railway in the early fall of 1927. Ten shallow holes were put down before freeze-up .and a considerable amount of surface trenching was completed. Based on the results of the surface trenching and the shallow diamond-drilling, an extensive development campaign was outlined. A winter road, 90 miles in length, was cut from mileage 55 on the Hudson Bay railway, and during the winter of 1927-28 a total of 2,600 tons of freight was hauled-in to the property. This freight included four complete diamond-drill outfits, two complete mining plants, building material for two sets of camps, and supplies for one year's operations, including 105,000 gallons of fuel-oil for Diesel engines.

Jan 1, 1933

By L. C. Graton

Introduction The Porcupine district of northern Ontario has yielded over $300,000,000 in gold during its twenty-three years of mining operations. It thus ranks among the foremost gold producing areas of the world. Of this $300,000,000 already produced from the District, the Hollinger mine has furnished over 60 per cent and stands as one of the greatest gold mines of all time. In 1929, the Hollinger Directors decided to supplement the current geological and development work by an intensive investigation of the geology of the mine. This special study, begun in June of that year, was completed in October, 1932. An account of the geology of the mine in a degree of detail commensurate with the intensity of the study is in course of preparation. But the widespread interest manifested at the present day in gold occurrence generally, in Canadian gold deposits, and in the specific results of the investigation at Hollinger, appears to justify the immediate presentation of a highly abridged summary of our principal findings, insofar as they relate to the more general and scientific phases of the geological situation. Those conclusions having direct bearing on operating and exploratory policy are not dealt with here. The present preliminary paper, therefore, records chiefly the conclusions reached, with little incorporation of supporting argument or evidence. While intended to give a reasonably balanced perspective of Hollinger geology, the condensed presentation naturally emphasizes those views which are not in complete accord with accounts hitherto published regarding this district.

Jan 1, 1933

By C. M. Campbell

The Inconceivable Wealth propaganda goes on apace. Premier King, at Vancouver, has stated that we still have, untouched, natural resources, "beyond the wildest dreams." Principal Currie, in an address before the Canadian Society in New York said that Canada's resources, "are as yet merely scratched and it is not possible to compute her almost fabulous natural wealth." Mr. Meighen, in the last election campaign announced that, "under the providence of God, Canada is more richly endowed, perhaps, than any other country in the world." Four years ago a despatch was sent to Premier King "on behalf of" this Institute advising him that "Inconceivable Wealth" in minerals in this country was assured. This was made as a statement ~f "incontrovertible fact." Specifically, this despatch stated that this wealth was on such a scale that the mining industry would in the future lead all others in this country. This inventory is still in effect as far as this Institute is concerned.

Jan 1, 1926

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT: As part of an overall study of properties and processes influencing consolidation of oil sands fine tailings resulting from different extraction processes, self-weight consolidation tests were per-formed. Fourteen 2 m and 1 m high standpipe tests were instrumented to monitor the rate and magnitude of consolidation of seven fine tailings materials. Tests provided valuable information about the variation of consolidation related to differences in fine tailings material properties that result from a change in bitu-men extraction process (caustic versus non-caustic). In addition, the effect of adding a coagulant to caustic fine tailings was measured. Test results are presented and discussed in terms of consolidation rate long-term volume decrease, compressibility, and downward drainage. Non-caustic fine tailings had fasterinitial consolidation, which is important in tailings ponds for reducing storage capacity and returning decant water at a faster rate to the extraction plant. Similar results were obtained for caustic fine tailings with a coagulant addition. However, long-term settlement of the different fine tailings appears to con-verge to a similar value over time because it is then governed by effective stress.

Jan 1, 2011