Search Documents

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

Prediction of fragmentation by blasting is most commonly based on theassumption that a single distribution of pre-existing discontinuities is present within a blasted rock volume and that the underlying mechanism of failure is tensile failure. It is assumed that the tensile stress field created by a blast initiates and extends radial cracks around the blastholes. Interaction between radial cracks from different blastholes and the free surface creates rock fragments. In reality, fragmentation of the rock occurs due to two mechanisms.One is related to the compressive-shear failure of the rock (mainly rock matrix) close to the blastholes, while the second mechanism is the previously mentioned tensile failure of the rock mass. The secondmechanism of failure occurs in the form of extension of the larger cracks in the region beyond the crushed rock, and this type of fragmentation occurs after the crushing phase. In the case of hard rock or blasting where the extent of crushing is minimal, the currently used prediction methods give a reasonably good result. However, there are many blasting conditions where the amount of rock crushing is significant. In the case where fragmentation of the given rock volume occurs dueto two different mechanisms, modeling of the rock fragmentation with a single distribution function is not appropriate. To model the fragment size distribution generated by two different mechanisms, it is necessary to use a two-component fragment size distribution function and a scaling parameter that will determine the proportion of the fragmented volume created by each mechanism. The purpose of this paper is to present results of blast fragmentation modeling based on two mechanisms of failure. The two-component model (TCM) utilises experimentally determined parameters from small scale blasting and parameters of the Kuz-Ram model, for more accurate prediction of the complete rock fragment size distribution curve. The methodology is such that it is possible to predict complete fragment size distribution, including fines, of ROM product for a future mine, at the feasibility phase of mine design.

Jan 1, 1999

The clay slime generatea in many sand washing operations is usually very difficult to de-water. Treatment of these slimes is often limited by economic considerations and the properties of the solids to a gravity-driven process. The moisture characteristics of kaolinitic slimes from two different sand washing operations were measured.From these curves, equilibrium moisture contents for sedimentation and for drainage were calculated using the methods of soil physics. The validity of these calculations were confirmed by column experiments.The results show that the increased de-watering to be gained by drainage, as compared with sedimentation, is significant. Furthermore, observed rates of outflow indicate that water can be removed considerably morerapidly when drainage is possible.The practical application of these results to the dewatering of clay slimes is discussed.

Jan 1, 1978

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

Selective Recovery of Platinum from Cobalt-Rich Crust

Sep 13, 2010

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

Size Separation Pretreatment and Alumina Recovery from Bayer Red Mud

Sep 13, 2010

The achievement of high availability of the Grey River Gold Mining Limited's alluvial gold dredge is a tortuous task which will rely upon the dedication of all staff employed at Grey River Gold Mining Limited (GRGML). The persistent adoption of new technology and better operating procedures, combined with a strong commitment to preventative and predictive maintenance, is necessary. The Grey River Gold Mining Limited alluvial gold dredge is operating in a relatively low grade alluvial gold deposit and hence relies on a high throughput of ore to be profitable. To achieve the required high material throughput the dredge incorporates an overburden removal system which operates simultaneously with a conventional bucketline system.   The overburden system incorporates a cutter wheel and suction pump configuration which is dedicated to removing the low grade (5 mg gold/m3 gravel) overburden. The bucketline conveys the richer grade payzone gravels (up to 890 mg/m3 gravel) to the recovery plant mounted onboard the dredge. The horizon for the overburden system approximates 15 m and the payzone terminates at the interface of the old man rock and the alluvial gravels at a variable depth averaging 22 m.   From a mechanical engineering perspective the dredge is a machine comprised of two materials handling systems which are controlled by Operations Staff and electronic process control systems.   The availability of such a materials handling system is a function of four variables: 1. The environment that the machine operates in. 2. The ability of the people operating the machine. 3. The design of the mechanisms, the configuration that they are grouped in and the effectiveness of the process control systems which control the mechanisms. 4. The procedures utilised to predict the performance of the machines and the skill of staff to analyse that data and carry out effective maintenance.

Jan 1, 1989

Experiment of Improving the Quality and Decreasing the Impurity of Titanium Concentrate in Panzhihua Mine in China

Sep 13, 2010

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By D J. Black

Ventilation modelling is used to evaluate ventilation system performance. This paper describes modelling to assess potential changes to a single entry longwall ventilation circuit to improve ventilation and gas management. The longwall panel is extracting a 215 metre face in a 1.5 metre coal seam at a depth of 900 to 1000 metres below surface. The 1.5 metre B seam is located approximately 25 metres below the main 3.0 metre A seam and the gas content of both coal seams is approximately 20 to 25 m3/t. The B seam is extracted prior to the A seam and the mine relies on fracturing of the overlying strata to induce gas emission from the A seam to reduce the gas content prior to mining. Longwall operations in the B seam are constrained by limited ventilation and high gas emissions. Due in part to statutory limits on gas concentration and air velocity, the average longwall production rate is approximately 700 t per day.Gate roads in the B seam are single entry, developed using road headers and supported with steel arches. Additional timber cog support is installed to reduce roadway closure from abutment loading. Due to the slow advance of gate road development, mine management were reluctant to consider significant mine design changes, such as two heading gate roads; therefore, the investigation focused on determining the extent to which ventilation and gas emission impacted on longwall production performance, while recommending short-term, low-cost actions to improve ventilation and gas management to support increased longwall production.CITATION:Black, D J, 2017. Application of modelling to improve ventilation and gas management in a single-entry longwall panel, in Proceedings Australian Mine Vent Conference 2017, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

By C MacDonald

There are many technologies available today in terms of fire and life safety in road tunnels. So many in fact that it is becoming more and more difficult for clients and contractors alike to determine what they want and what they need. From a clientÆs perspective, fire and life safety is about protection to its infrastructure and to the public at large. Conversely, the contractor is looking to meet its æfit for purposeÆ or ædeem to complyÆ requirements in the most economic and practicable way. Practices regarding fire and life safety in road tunnels have undergone a degree of transformation during the last decade or more throughout the world. This transformation has largely been driven by a series of catastrophic accidents such as the major fires in Europe including the Mont Blanc Tunnel, Tauern Tunnel, Saint-Gothard Tunnel, and now most recently in the CityLink Tunnels in Melbourne. International guidelines produced by organisations such as the Permanent International Association of Road Congresses (PIARC), the European Union, the International Tunnelling Association (ITA) and the US National Fire Protection Authority (NFPA) now provide clients, owners and designers with the tools required to define and specify the required fire and life safety systems in road tunnels. The majority of these tools are based on risk assessment and risk management. Recent road tunnel projects within Australia, however, have not referred solely to such guidelines. Clients have opted to prescribe different or additional fire and life safety requirements within the projectÆs technical specification documentation (project requirements), leaving designers and contractors with little room to implement alternatives or substitutions. Further, these project requirements are largely dictated by practice established on previous road tunnel projects within Australia. This paper looks at the current international guidelines and practices and undertakes a comparison with the EastLink tunnels in Melbourne and other road tunnels within Australia and makes assessment on whether Australian methods are the most appropriate for clients and contractors alike. Focus is directed to the key elements of fire and life safety such as:traffic envelope, barrier arrangements and emergency walkway provisions;deluge systems;drainage systems;fire rating requirements;tunnel ventilation systems;cross passage provisions;fire safety assessment;critical intelligence systems including help phones, CCTV, incident detection, tunnel signage, etc; andexternal tunnel control systems.

Jan 1, 2008

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By S Jahanshahi, D R. Swinbourne

A knowledge of the value of the activity coefficient of cobalt oxide in slag as a function of composition and temperature is necessary if effective strategies are to be devised to maximise the recovery of cobalt in nonferrous smelting processes. This work reviews previous studies and shows that comparison and evaluation of the results is hampered by variations in the choice of standard states for the species. Published results have been recalculated to a common set of standard states with a preferred value for the Gibbs free energy of formation of cobalt oxide. It has been shown that the value of the activity coefficient of cobalt oxide referred to the solid standard state in iron silicate slags is approximately two, at temperatures from 1523 to 1623¦K. It is suggested that some contradictory results are most likely due to errors in the measured partial pressure of oxygen.

Jan 1, 1998

By C A. Locke

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dyke/stock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.  

Jan 1, 1995

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

By M J. Andrews, P J. White, I Bogie

Active geothermal systems occur widely in Sumatra and in the Taupo Volcanic Zone (TVZ) ofNew Zealand. There are also many occurrences of epithermal gold mineralisation in Sumatra, some of which are economic. Minor sub-economic occurrences of gold have been reported in the TVZ but none have yet been mined. There are both similarities and differences in the nature of the active geothermal systems and mineral deposits in Sumatra and New Zealand, which can be systematically related to the tectonic setting. The thicker crust and consequent predominance of silicic volcanism in New Zealand leads to hydrothermal systems which are little eroded and with limited lateral outflows. The systems in Sumatra are of mixed character, with some of the characteristics of those in andesitic island arcs such as Java or the Philippines, e.g. a higher proportion of systems with identifiable acid magmatic volatiles, a greater potential for deep erosion and lateral outflows than in New Zealand; but modified by the more oblique component of subduction and thickened crust so that some are localised in volcano-tectonic depressions and consequently have high piezometric levels of primary hydrothermal fluid. The unusual occurrence of calcic zeolites in veins associated with gold mineralisation in Sumatra is thought to be indicative of æsatelliteÆ boiling zones along de-gassed hydrothermal outflows.

Jan 1, 1995

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901

Study on Selective Reduction and Magnetic Separation of Low-Grade Nickel Laterite Ore to Produce High Nickel Concentrate

Sep 13, 2010