Search Documents

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

By Lance A. Roberts

Micropiles are commonly utilized for applications other than foundation retrofit. In bridges, for example, micropiles can serve as the permanent foundation elements or can be used in temporary support applications. In this paper, a case study on the use of micropiles for the 18th Street Expressway Bridge rehabilitation/repair project in Kansas City, Kansas is presented. In the project, micropiles were utilized for support of six temporary jacking structures, which allowed the bridge to be lifted while repairs were completed. A group of six micropiles was required to support each jacking structure. The required compressive service load per micropile was approximately 300 kips (1300 kN) and the settlement of the micropiles under the service load was to be limited to 0.5 in. (12.7 mm). Two field compression tests were conducted as part of the project. The field load test data was integrated within a soil-structure interaction capacity approach in order to analyze and permit the shortening of the design bond length for the production micropiles.

Jan 1, 2009

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines (MRMR Best Practice Guidelines) were prepared by the Canadian Institute of Mining, Metallurgy and Petroleum's (CIM) Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee) to update an earlier version that was accepted by CIM Council on November 23, 2003 (CIM, 2003). These 2019 MRMR Best Practice Guidelines supersede and replace the November 23, 2003 version of the MRMR Guidelines. These 2019 MRMR Guidelines are not intended to be prescriptive and are not intended to provide detailed and exhaustive instructions for preparation of Mineral Resource and/or Mineral Reserve (MRMR) estimates. Rather, they are intended as general guidance to assist professional geoscientists (or equivalent) and engineers (or equivalent) in preparing high quality estimates of MRMR that incorporate sound geoscientific, engineering, evaluation and design practices. They are based on well-established estimation and mine planning principles and are designed to provide general guidelines of best professional practices employed in the preparation of MRMR estimates. Although the 2019 MRMR Best Practice Guidelines are intended for use by Canadian-based mining/exploration practitioners, many of the concepts and practices presented herein are in general agreement with current industry practices in jurisdictions with membership in the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). For this document, persons preparing MRMR estimates are called Practitioners. Preparation of MRMR estimates should be carried out by Practitioners who either hold the status of Professional Geoscientist (or equivalent) or Professional Engineer (or equivalent), or who prepare the estimates under the supervision of a Professional Geoscientist (or equivalent) or Professional Engineer (or equivalent). For the purposes of this document, all references to reporting describe such necessary reports and related documentation that are created as part of the normal-course work flow of preparing MRMR estimates for internal purposes. For clarity, all public disclosure of MRMR estimates made by, or on behalf of, an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time. At least one Qualified Person (QP) must take responsibility for each part of the estimation process when publicly disclosing the results of MRMR estimates. The intended audience for these 2019 MRMR Best Practice Guidelines includes Practitioners at all levels of skill and experience, government agencies, academic institutions, and the public.

Nov 29, 2019

By J. W. Baker

"The Kerr-Addison mine is on the northeast shore of Larder Lake in the township of McGarry, District of Timiskaming, Ontario. It lies just south of the highway leading to the town of Kirkland Lake, 25 miles to the west.The property was first staked in the summer of 1906, by a party of prospectors led by a Dr. Reddick of Ottawa. Subsequent assessment work resulted in the erection of a 20-stamp mill in 1908. Gold from this mill was used in the first gold coins to be minted in Canada. The operation did not prove successful, however, and mining was suspended. In 1914 a consider-able amount of underground development was undertaken by the Associated Goldfields Co., without success.In 1936 Kerr-Addison Gold Mines Co. carried out large-scale sampling from four adits driven into the hillside at the mine. Results were not satisfactory, but it was decided to drill one last deep diamond drill hole from surface. The hole cut a wide section of gold ore. With this encouragement, further development outlined a large tonnage of ore, and a 500-ton mill was put into production in May, 1938. In 1939, its first full year, the mine produced 54,480 ounces of gold and 2,732 ounces of silver. By 1955 the mill had been expanded to a rate of 4,549 tons daily, and in this year 427,193 ounces of gold and 23,490 ounces of silver were produced.From 1938 to the end of 1955 the total production, from 17,473,797 tons milled, has been 3,607,462.74 ounces of gold (0.2064 ounces per ton), and 182,278.56 ounces of silver, with a total value of $131,073,037."

Jan 1, 1949

By Joseph A. Corgan

The river- or dredge-coal industry of Pennsylvania is conducted on many of the rivers and creeks that drain the Pennsylvania anthracite fields. Coal thus recovered found its way into the streams as coal was being prepared for market by the anthracite industry proper, in the northeastern part of the State. The Principal rivers draining; the fields, those where dredging is taking place, are the Susquehanna, Schuylkill, and Lehigh. Several creeks - the Shamokin, Mahanoy, Wiconisco, and Swatara - also are productive sources of river or creek coal. Operations along the streams cover a wide territory, and along the Susquchanna alone; dredges are recovering coal for about 160 miles. Anthracite was a significant factor in the early industrial development of the United States. Industry used it to generate steam, and railroads used it as fuel for locomotives; but it probably was most important industrially in the smelting of iron ore. For more than a hundred years homes have been heated with this fuel. From the beginning of mining in 1807, to 1940, more than 4 billion net tons of anthracite had been prepared and shipped to market. In the preparation process much of the smaller-size coal and refuse found their way into rivers and creeks which carried the material many miles. This study is concerned with the recovery of that anthracite from those rivers and creeks.

Jan 1, 1942

By Bernard Lewis

This report summarizes fundamental research end technical studies conducted in the Explosives and Physical Sciences Division, Region VIII, of the Bureau of Mines in the 2 years July l, 1950, to June 30, 1952. It is the fifteenth of a series of, ordinarily, annual reports whose aim has been to provide the reader with a resume of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report. ACKNOWLEDGMENTS Acknowledgments art, made to the following members of the Division wider whose mediate supervision the described studies were carried out. Stuart R. Brinkley, Jr., chief, Mathematical and Theoretical Physics Section, and special assistant to the chief of the division.

Jan 1, 1953

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

By S. L. Huang

The location and shape of potential failure surfaces in soil slopes were directly determined based on the stresses induced in the soil mass and the strength of the soil itself. Stress calculations were carried out by the finite element method with the Drucker-Prager nonlinear material model. The Mohr-Coulomb failure criterion and Mohr's circle stress analysis were then applied to the calculated stresses to determine the characteristics of the failure surface.

Jan 1, 1989

By Raymond B. Ladoo

The uses for which ground talcs are suited closely depend upon their physical and chemical properties , but , in spite of this fact , little scientific investigation has been made in order to devise quick and accurate tests for the determination of these properties . The chemical properties of talc are inherent and may not be altered or modified except by selective mining or by chemical processes not practical in the present status of the industry . However , the determination of chemical properties is not so important , for most uses , as of physical properties , although sometimes certain chemical characteristics are perhaps unduly insisted upon by chemists in some industries . Physical properties are dependent both upon mineralogical characteristics and upon methods of grinding and sizing and may thus be partly changed or modified by changes in practice . There is so little known of the chemistry and physics of the various processes in which talc is used that the purchase and sale of talc is governed more by rule- of- thumb methods dependent upon individual opinion and often , prejudice , than by accurate , standard tests . This not only causes unwarranted price fluctuations , but injures both the producing and consuming industries by creating false ideas of the suitability of talc for various uses . It thus seems important that present tests be standardized and made uniform for the whole industry , and that new tests devised to fill the existing gaps .

Jul 1, 1920

By FREDERICK MCAKCCOY

THE production of tin from Mexico has never reached the point of being considered a national industry, but the distribution of tin ores is so widespread that there are possibilities that one day it may become of importance. Of the twenty-seven states of the Republic, tin claims have been taken up in sixteen. In all there had been taken up to the end of 1926, two hundred and twenty-five claims, of a total area of about 7400 acres. The first historical mention of tin in the Americas is found in a letter of Cortez to the Emperor, Charles the Fifth, of Spain, which is as follows: Speaking of his manufacture of some small cannon, he says: "For these reasons I took considerable pains to get copper from some provinces of this country, and bought it at a high price in order to get it quicker.

Jan 1, 1929

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35'/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.'?,' "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970