Search Documents

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

LAKE MARGARET is situate high up on the West Coast Range of Tasmania, and lies in a roughly triangular valley formed by the ridge of Mount Sedgwick on the south, the ridge formed by Mounts Geikie and Tyndal on the west, amid a ridge connecting Mounts Geikie and Sedgwick on the east. Any description of this hydroelectric installation, however brief, naturally divides itself into the following sections:1. STORAGE BASIN, &c. 2. DAM. 3. PIPE LINES. 4. POWER STATION. 5. TRANSMISSION LINES. 6. SUBSTATION 7. VARIOUS WORKS utilizing the power.The Storage Basin used is the natural lake itself, which has a maximum length of 110 chains, a maximum width of 40 chains, and a mean arelj. of 300 acres. The water-level of the lake, which has been maintained by a natural dam, is 2143 ft. above sea-level. The approximate catchment area at present appropriated is 7 sq. miles, and the rainfall, on the average, about 144 in. per annum. It is possible to increase this catchment area by suitable races, &c. Dam.-The dam constructed is of very small dimensions, and is not a storage dam in the usual sense of the term. The natural storage ot-the lake itself was used by means of a channel cut through the natural dam and thence to the mouth of the lake, the lake level being thus temporarily lowered while the outlet pipes, screens, &c., were placed in position, and the channel was then closed again with a concrete wall in which the pipes and screens are set. This channel was cut partly through rock and partly through sand and conglomerate boulders for a total...

Jan 1, 1915

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By Christopher P. O?Connor

Stereolithography is a well known rapid prototyping technique in the manufacturing sector. Essentially it is a three dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of Rapid Prototyping Techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models and in cases where it is decided to develop physical models, the process is time consuming based on simplified constructions. Rapid prototyping techniques (RPTs) such as stereolithography can facilitate engineers and geologists to quickly and with satisfactory accuracy to visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with the Department of Mines Research of Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs (e.g. stereolithography) to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems.

May 1, 2002

By J. W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles. as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain. GEOLOGY The rocks of Jumbo Mountain comprise a series of folded Tertiary sediments forming a belt one half to three quarters of a mile wide, trending northwest about parallel to the strike of the beds. This belt is sandwiched between two extensive in-trusives—gabbro on the northeast and quartz dio-rite on the southwest—and has been intruded by dikes of fresh and serpentinized dunite. Shear zones follow many of the dunite-sedimentary rock contacts, and in these the nickel mineralization is concentrated. A few transverse faults offset the sediments and ultrabasics. Sedimentary Rocks: Two kinds of quartzite make up the greater part of the sedimentary section. One is dark purplish gray, very fine-grained, and thin-bedded; the other is light gray to white, medium-grained, and well-bedded. Locally the light-colored quart lites contain grit and conglomerate horizons, rich in pebbles of white chert and very fine-grained quartzite. Intercalations of dark argillites near the summit of the mountain give many of the cliffs a striking banded appearance. Dark gray to black, aphanitic, thin-bedded argillites occur throughout the entire sedimentary belt. Beds vary from a few inches to a few tens of feet thick and some, near the summit, contain numerous fossile (willow?) leaves. Only the thicker beds were mapped. The sediments are quite fresh on the northeastern side of the belt and become more metamorphosed (hornfelsed) toward the southwestern side. Brown biotite is present in the metasediments in increasing amounts as the quartz diorite is approached. Near the intrusion, porphyroblasts of plagioclase, up to 1 in. across, testify to the soaking of sedimentary rocks by solutions emanating from the quartz diorite. Most of the sediments mapped lie along the southwestern limb of an anticline, the axis of which follows the crest of the mountain and plunges at a low angle to the northwest.

Jan 1, 1961

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Chris Ringas

The safe operation of gas transmission pipelines is increasingly coming under the spotlight. Increasing environmental pressure is also forcing pipeline owners and operators to ensure the integrity of their pipelines. The integrity of a pipeline is usually determined using intelligent pigging, often referred to as In Line Inspection (ILI). However, in many cases, gas pipelines cannot be pigged for a variety of reasons. The National Association of Corrosion Engineers (NACE) has recently published Recommended Practice (RP) 0502, referred to as the External Corrosion Direct Assessment (ECDA) Methodology to assist pipeline owners with assessing the condition of pipelines that cannot be pigged. 2. External Corrosion Direct Assessment - NACE RP 0502 The ECDA Methodology is conducted in four phases as follows: ? Pre-Assessment ? Indirect Inspection ? Direct Examination ? Post-Assessment In the Pre-Assessment Phase, all the relevant historical and current data relating to the pipeline in question is reviewed. This covers pipeline, construction, soils/environmental, corrosion control and operational data. The aim of the Pre-Assessment Phase is to determine whether ECDA is feasible, and if so, to define the ECDA Regions and finally to select the Indirect Inspection Tools that will be used for each region. Typical overline techniques used for overline surveys include the following: Voltage gradient surveys ? DCVG or ACVG

Jan 1, 2006

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By W. D. Northrop

This paper gives an account of the development of a technique whereby the vertical limits of geological horizons may be identified by the use of vertical variograms on the mineral of economic interest. This information may supplement or guide the correct subdivision of the individual horizons into meaning full data sets by diligent geological observation. This process then improves the quality of the variance modelling of the gold distribution in the plane of the individual layers and therefore enables better estimates to be made into the grids or blocks of the mine model. The technique is explained by an account of the development work, which was performed, on duplicate superimposed reef horizons in the Kimberley formations. The paper then shows how the correct approach was developed to evaluate the mineralized layers in a multiple stacked conglomerate layer sequence in the Elsburg reefs of the Witwatersrand Rand System at the Target deposit. The method of categorization of resources according to confidence in the estimate is also explained. The feasibility processes carried out on the three-dimensional model, in accordance with the SAMREC code are also described. An example of the development of a reconciliation process utilizing chip sampling is also explained.

Jan 1, 2003

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By Bruce Conard

For many years, Bruce Conard has been engaged in reading about and discussing the desired sustainability of the mining and metals resource industry. He has, however, become concerned that there is a greater issue that requires our urgent attention: what challenges do we face as a global society? His Distinguished Lecturer presentation traces the idea of environmentally sustainable economic development but concludes that a business’ interest in its sustainability is predicated on the sustainability of our global society. Conard reviews some of the most serious challenges, including population growth, clean energy supplies, freshwater availability and climate change, and calls on scientists and engineers not only to apply their skills in helping solve these challenges, but most urgently, to speak with intelligence and passion about the need to act now.

Jan 1, 2014

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated program over a 37-month period (April 1978-May 1981) as part of an economic feasibility study. The program included more than 120 km of core drilling, 63 km of access road construction under adverse topographic and climatic conditions, detailed geological mapping, plus other related activities. This Tertiary-age copper-molybdenum deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. Both intrusive and extrusive igneous rocks are present. Erosion, oxidation, leaching, and supergene enrichment of copper have resulted in a deposit now exposed at the surface that contains more than 368 Mt grading about 1% copper equivalent as sulfides.

Jan 1, 1982

By A A. Ndiaye, A Galli

In a companion paper on current hedging practices in the mining industry (Armstrong et al, 2009) we showed that contrary to popular belief, mining groups are still using financial derivatives to hedge against foreign exchange risk and interest rate risk, and more recently against adverse changes in energy prices, notably the oil price. This paper presents a case study on a hypothetical gold mine to illustrate the impact that hedging policies could have on its profitability by reducing the downside risk due to adverse changes in the exchange rate and increases in fuel prices. The characteristics of the hypothetical mine have been set to reproduce those of a real gold deposit, the Kisladag mine that is currently being exploited by open pit methods in Turkey. This mine was selected because its feasibility study was available to the public. Geostatistical simulations are used to reproduce the inherent uncertainty on the recoverable reserves û stochastic simulations are used to generate the variability of the other three key sources of uncertainty: the gold price, the cost of energy and the exchange rate. A simple strategy based on straightforward vanilla options (puts and calls) was developed for hedging the last two risks, on the assumption that the company sells its production at the prevailing spot price.

Jan 1, 2009

By Will Mitchell

The classical definition of a beneficiation engineer as one who treats an ore in order to separate and discard worthless fractions by essentially physical means is obsolete. Technology in the profession has advanced so rapidly during the last two or three years that educators have not been able to coin definitions to keep up with the pace. In the past some people have hesitated to include leaching or even agglomeration as minerals beneficiation, because of the major chemical changes involved. This view has fallen by the wayside, especially because a majority in the profession have become actively involved in extraction and pyro processes that go far beyond the original definition of mineral dressing. To say that there is a great revival of interest in leaching is putting it mildly, for the uranium business, like the gold business, now depends almost entirely on leaching. This revival of leaching, long overdue in mineral engineering, has been stimulated this year, especially as a result of the relaxation of security restrictions surrounding the recovery of uranium from its ores. It has brought new unit operations to minerals beneficiation, namely ion exchange and solvent extraction. These operations have appeared as resin-in-pulp, solvent-in-pulp, and liquid-liquid systems. In many cases these leaching and separation procedures, now reaching the production stage, have been engineered by minerals beneficiators. The trend toward leaching has also had impact on the technology of beneficiating other nonferrous minerals, especially copper, manganese, columbium, tantalum, nickel, cobalt, titanium, and the rare earths.

Feb 1, 1956

Jan 1, 1991