Search Documents

By M Blanch

Gas management practices across the Australian underground coal industry have evolved significantly since the early nineties with the introduction of hazard management plans, directional drilling techniques, surface gas predrainage methods, and the widespread use of ventilation and gas reservoir simulation software.The improvements are evidenced by a substantial reduction in the occurrence of outbursts and gas related delays during a period where coal production rates have increased three to four fold. The development of effective gas predrainage strategies have been afforded by the use of reservoir simulators and a significant increase in the availability of measured gas reservoir data, in particular gas content and composition, adsorption isotherms and permeability. That said significant opportunities remain to optimise gas drainage designs and increase certainty in the gas predrainage design process through an enhanced understanding of coal seam permeability and how it is applied in the gas drainage design process.This paper describes the discrepancies between measured and actual seam permeability found during the recent assessment of two pilot predrainage programs executed in the coal measures of Queensland’s Bowen Basin. The results of those programs illustrate the need to better understand the validity of measured permeability data. The history match method employed in the pilot well assessments is proposed as an integral step in the routine gas drainage design processes that will ultimately lead to increased certainty and flexibility in gas predrainage practices.CITATION:Blanch, M, 2017. Coal seam gas predrainage optimisation through an enhanced knowledge of coal seam permeability, in Proceedings Australian Mine Vent Conference 2017, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

By W. P. Erasmus

This paper will focus on the use of the ?wet-mix? steel fibre re-in forced shotcrete as a permanent lining in deep shafts, assessing gold bearing reef. It will cover all aspects relating to the choice of this material covering the geological conditions through to the final quality control. All procedures are in line with ISO 9001,as JCI projects who manage the project, are an approved company therof.

Jan 1, 2001

By Sean Gallagher

This report was written in an effort to provide better control measures for low back pain (LBP) and low back disability in the mining industry. There are numerous factors associated with development of LBP, many of which can be effectively controlled while some cannot. Better job design is promoted as the best method of reducing cases of LBP and can also reduce the disability (i.e., lost time from work) associated with LBP when it happens. The report draws attention to what is currently known about LBP, what the causes are thought to be, and discusses recent back injury trends in the mining industry. Research describing unique physical demands in mining, such as the capabilities and limitations of working in awkward postures, is also presented. Methods that can be used to prevent initial LBP episodes are provided, including facilities design and layout for materials and supplies, use of mechanical-assist devices, improved design of lifting tasks, and better seat design. Methods of reducing the disability associated with LBP (including workplace design, proactive return-to-work efforts, communication, and management commitment) are also discussed. The report concludes that control of LBP and disability in mining requires a comprehensive approach to limit the repetitive loading that can occur on the low back due to manual materials-handling tasks and exposure to whole-body vibration (WBV). Specific recommendations include the following: ? Successful LBP prevention efforts require a proactive program that has strong management commitment and incorporates employee involvement. ? More efficient supply handling systems and use of mechanical-assist devices can greatly reduce exposure to hazardous lifting tasks. ? Lifting tasks should be designed to minimize low back stress. Tools to evaluate and redesign lifting tasks are presented. ? Improved seat design can reduce exposure to WBV and improve posture, leading to reduced LBP risk. ? The disability associated with LBP can be reduced. Getting the worker back on the job as quickly as possible is in the interest of everyone involved.

Sep 1, 2008

By Roberto Folchi

This note deals about the controlled demolition work for the dismantling of an industrial structure in San Seplocro, Italy. The structure to be demolished, the FLOWERS SILOS, consisted in a multilevel reinforced concrete frame supporting r.c. silos and steel silos. This was standing near civil buildings and was adjoining a warehouse that had to be safeguarded for being renewed.

Jan 1, 1994

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By D. R. Gagnon

Mining companies are continually looking for product-ivity and efficiency improvements with their equipment to reduce operating costs. This paper will review the results of a productivity analysis conducted at the Luscar Ltd. Boundary Dam and Bienfait mines near Estevan, Saskatchewan using a Computer-Aided Earthmoving System (CAES) installed on a track-type dozer. The CAES TTT system is a Global Positioning System that provides the operator with constant survey guidance. The study includes a productivity comparison between two similar test sites, one with the aid of the CAES system and the other, without. The CAES TTT system shows a productivity improvement of between 20 and 35% in the reclamation slope leveling application. Even with the CAES TTT system deactivated, some of the advanced features of the system were used to: retain terrain data for volume calculations; track the equipment position; and, accurately record and separate idle time from working time.

Jan 1, 2002

By Sushil Bhandari, Amit Bhandari

Blast optimization in open-pit operations is a task that often remains at a theoretical stage. Indeed, when it comes to operational blast design and onsite implementation, time restrictions and field conditions make it difficult to execute a planned pattern accurately and optimization according to local conditions is even more difficult. For example, adjusting a drill pattern to a complex face geometry is not something that can be easily undertaken on site. Blasters and engineers will do their best trying to distribute boreholes over the bench and even then, it can take them hours to achieve an acceptable layout. Similar situations occur with delay sequences, when trying to adjust them to address selectivity or vibration issues. For these reasons, operational blast design will often remain at a very basic level and the required adjustments are laid aside due to the difficulty of implementing them on site.

Jan 1, 2019

CONTENTSSummary.Introduction.Location and Geology.Historical and Exploitation.Part 1. Washability Characteristics of the Liddell.Seam.Foybrook Open Cut, Top Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Part 2. Washability Characteristics of the LiddellSeam.Foybrook Open Cut, Bottom Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Acknowledgments.References.INTRODUCTIONThe washability characteristics, size-range and chemical analyses of the screening from the Liddell Seam are matters of growing interest in view of the increased exploitation of this seam over the last few years, and also since the Newdell Coal preparation plant of the New South Wales Mining Company Proprietary Limited, utilizing magnetite heavy media separation, commenced...

Jan 1, 1954

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By Ronald F. Balazik

This Bureau of Mines study identifies and examines the costs of Federal, State, and local environmental protection controls on domestic phosphate rock mining, The costs include the expenditures needed to comply with government regulations and the effects that these expenditures and regulations have on supply. The study analyzes costs of environmental impact assessments, air and water quality standards, reclamation laws, potential solid waste controls, and local government restrictions. In addition, an industry survey and the Bureau's Minerals Availability System (MAS) are used to evaluate land management policies that restrict access to phosphate resources, Conclusions drawn from these analyses confirm that (1) domestic phosphate mining has incurred substantial control costs and may be subject to significant new regulatory costs in the next several years, (2) certain environmental controls can discourage mining investment, (3) environmental policies governing land-use controls affect the disposition of sizable phosphate resources, and are key determinants in the development of those resources on the Federal do- main, and (4) environmental costs could diminish the competitiveness of domestic producers.

Jan 1, 1983