Search Documents

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By Minji Jun

Leaching of the surface-coated metals from waste acrylonitrile butadiene styrene plastics (WABSP) has been investigated in the ammoniacal solution. The ammoniacal leaching of WABSP (typically containing 4.1 wt% Cu, 1.3 wt% Ni, 0.03 wt% Cr) efficiently dissolved copper and nickel, leaving unleached chromium as fine particles. The results indicate that the anions of different buffer media for metals leaching follow the order: CO3 2− > Cl− > SO4 2−. A declined leaching with high NH4OH–(NH4)2CO3 ratio (8:1) and a steep rise in extraction with high pulp in solution revealed the influence of anion (CO3 2−) and cation (Cu2+) present in the system. The leaching performed in carbonate solution by maintaining 5.0 M total NH3 concentration as NH4OH–(NH4)2CO3 ratio, 4:1; pulp density, 200 g/L; agitation speed, 400 rpm; temperature, 20 °C and time, 120 min yielded the maximum extraction (>99%) of copper and nickel. The study reveals a plausible recovery of the surface-coated metals from the WABSP without altering the properties of polymer material that can be recycled separatel

By S. Abe

An extensive study has been carried out to determine the true cause of floating slimes precipitation which sometimes occurs and badly affects the quality of copper cathodes. Soluhilities of floating slime compounds systematically measured for the ternary system As-Sb-Ri added solely or in combination with conventional copper electrolyte (63°C) and bench scale electrorefining experiments done by varying electrolyte composition, have shown conclusively that the level of Sb(V) ions plays a substantial role in the precipitation mechanism. It was, therefore, speculated that controlling the level of the less soluble S b ( V ) ions below a certain critical level should result in a complete elimination of the undesirable precipitation. This can be easily achieved, for instance, by the addition of a reducing agent such as SO2 gas and the simultaneous employment of a certain type of cheating agent that effectively removes excessive Sb and Bi from the contaminated electrolyte. Long-term pilot testing conducted in line with the above speculation has confirmed the SO2/chelating resin scheme to be industrially very attractive and feasible.

Jan 1, 1987

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By W. E. Straszheim

Computerized microscopic techniques were used to determine the size and identity of the ash-forming mineral components, as well as their association with the organic coal matrix, in order to aid in the development of physical methods of beneficiation which require such characterization for the most effective cleaning. Examples of particle size measurements, mineral phase identification, and especially coal-mineral association results are given for selected samples of raw and physically cleaned coals. These measurements can reveal certain characteristics of coals which can be be of significant value in predicting coal recovery and mineral matter rejection for coals undergoing beneficiation.

Jan 1, 1989

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By Thomas Niehoff, Yin Qing, Wei Zhongling, Liu Yongguo, Zhang Deliang, Tang Le

The gold ore of Shandong Gold Mining (Xinhui) was a refractory ore, which contained multi metallic sulfides (ZnS and PbS etc.) and carbonaceous. The gold ore concentrate came into leaching process and thickener and zinc replacement to recover gold. In order to improve gold recovery, the GOLDOX™ hydrometallurgy process was studied in Shandong Gold (Xinhui) by bench scale and 6 month plant scale test supported by Linde Gas. It was shown that the process promoted the leaching kinetics and improved gold recovery. The residue grade reduced 0.22 g/t in average after oxygen was applied. This indicates an operating profit increase 850,000 yuan/a in the plant. It was setting a good example for similar gold mine plant and would promote the oxygen application in Chinese gold mining industry.

Jan 1, 2015

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By Miguel N. Herrera

The electrochemistry of coal pyrite is relevant to coal desulfurization by chemical or bacterial leaching, flotation and oil agglomeration. The electrochemical behavior of polished and etched Upper Freeport and Pittsburgh coal pyrite samples was investigated from pH 1.0 to 10.5. The open-circuit potentials decreased with increasing pH, as expected, but were well above the thermodynamic stability region of pyrite, and decreased with time. Cyclic voltammetry revealed behavior highly sensitive to pH and scan rate (2.0 and 20.0 mV/s). The behavior on the first cycle was always substantially different from that on subsequent cycles. The anodic and cathodic reactions were correlated with the Eh-pH diagram for the Fe-S-H20 system to identify the reactions occurring at different pH values. There was also evidence that the buffers used to maintain basic pH values are themselves electrochemically active, which should be considered in interpreting many earlier electrochemical studies of sulfide minerals.

Jan 1, 1994

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998

By H. H. Kellogg

The thermochemical properties of molten solutions in the binaries Cu-Bi, Cu-Sb and Bi-Sb, as well as the ternary Cu-Bi-Sb, have been correlated and described in mathematical form by use of the associated species concept combined with the three-suffix Margules equations to account for the non-idea 1 behavior of the solution species. Agreement of the correlations with experimental data is excellent (relative deviation of less than 2.5% in the values of the activity coefficients) in most cases. The correlations are applicable over the entire composition range of each system, and in the temperature range 700°-1250°C.

Jan 1, 1985

By Jean Goldschmidt

Recycling of fine oxidized particles of non-ferrous metals usually cannot be carried out by pyrometallurgical methods. 'Hydrometallurgy provides an alternative technology to reintroduce? the resulting products as secondary raw materials into the industrial cycle, thereby saving resources and energy while keeping the environment a little cleaner. The paper summarizes the methods employed by Hydrometal to achieve these objectives and? stigmatizes the latest counterproductive international regulations which create ever more obstacles to environmentally sound recycling.

Jan 1, 1995

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By Martín Reyes

Iron concentration by ion flotation techniques, from sulfate solutions in presence of zinc was studied in a laboratory flotation column by continuous mode using a synthesized sand shell plate sparger, an anionic collector, promoters, and surfactant propylenglicol 400. Effects of experimental parameters, such as the concentration of reagent: potassium amyl xanthate and dithiophosphate, superficial gas velocity, and superficial liquid velocity were studied in terms of the recovery and enrichment of Fe (III). The results show that the iron elimination from the solution in the presence and absence of zinc (II) are of 59 % and 72 % respectively. The flotation efficiencies decrease with an increase of the concentration of xanthate and air flow rate. The best recovery was achieved, at Jg 0.1 cm/s, Jl 0.72 cm/s and a mixture of xanthate and dithiophosphate as promoter. It was also demonstrated that it is possible to selectively separate and concentrate iron (III) from solutions containing zinc. The behavior of iron ion flotation in a flotation column is reported in this research as a gas hold up, superficial gas velocity, bubble size and superficial bubbles area flux function. The results show that the extraction of aqueous ions of metal iron by ion flotation is strongly affected by: [C], Jg (cm/s), eg (%), Db (mm), Jl (cm/s), y Sb (s-1).

Jan 1, 2009

By Zvi Rivlin

Classical nucleation theory states that in first order phase transformations, such as liquid to solid transition, nucleation of the product phase starts with the formation of small, unstable clusters (embryos). When the thermodynamic barrier to nucleation is overcome, the embryos grow and attain a critical size, beyond which they are stable, i.e. they become nuclei. If nucle- ation does not occur, the parent, liquid phase remains in metastable equilibrium. At temperature lowers, undercooling increase and atomic mobility decreases. The viscosity change in the undercooled liquid may result in the formation of glassy state. As demonstrated in previous papers [I-21, in solidification involving surface nucleation of the product phase, as the case is in rapid quenching by melt-spinning, both nucleation temperature and nucleation time depend upon the number of atoms available at the isothermal surface in contact with the substrate. As a result of the thinness of the melt-spun ribbons, the embryo clusters that form at the freezing temperature may not be supplied by the amount of atoms necessary for their growth to critical nuclei sizes. In such extreme conditions, the liquid does not crystallize, it forms a metallic glass. A numerical simulation method is proposed for the reactions involved in embryo cluster formation and growth, at the atomic level. The simulation enables the caIcuIation of either the nucleation or the glass transition temperatures. Calculations made for the well-known glass forming CuZr and FeB systems afford prediction of the geometrical and thermodynamically conditions necessary for the formation of either crystalline or amorphous ribbons in melt-spun ribbons.

Jan 1, 1994

By Eulogio Velasco, Jose Nino, Marcos Cardoso

"Recycling of aluminum scrap for production of secondary alloys used for automotive applications is increasing continuously. Automotive alloys require a strict control to remove alloy impurities, inclusions and excess of magnesium. The advantage of aluminum is its recyclability with large energy and emission savings with minimal loss in material properties. The aim of this work is to study the magnesium removal from recycled aluminum by chlorine injection in a reverberatory furnace, and removal by an oxidation process at high temperature in an industrial rotary furnace.The magnesium removal by gas injection is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors. In the rotary rapid oxidation of aluminum and magnesium elements at high temperature is characterized by the formation of surface films composed of magnesium oxide. Additionally this work reviews the benefits of an efficient demagging process.IntroductionThe advantages of using light alloys for automotive applications include fuel economy improvement, greenhouse gas reductions and polluting emissions. These characteristics makes the aluminum alloys an attractive option for automotive components such as powertrain products and other critical parts like cylinder heads and blocks. [1]Aluminum alloys coming from recycled automotive components, used beverage cans (UBC) and wrought alloys have positive effects in the energy savings and current environmental trends. Producing a scrap recycled aluminum ingot consumes approximately 5% of the energy required to produce a primary aluminum ingot from bauxite ore. [2]"

Jan 1, 2011

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

By Ibrahim Yusufoglu, Ahmet Orkun Kalpakli, Cem Kahruman, Sedat Ilhan

"The effects of oxalic acid concentration, temperature, stirring rate and particle size on the dissolution rate of synthetically prepared calcium molybdate were investigated. Dissolution of calcium molybdate in oxalic acid solutions takes place as a series - parallel type reaction. In the first reaction step, which proceeds according to the ""Langmuir - Hinshelwood Mechanism"", calcium aqua oxalato molybdate is formed as a complex chelate intermediate product. In the second reaction step, molybdic acid is formed during the slow hydrolysis of calcium aqua oxalato molybdate, and it reacts rapidly with oxalic acid to form the polymeric hydrogen oxalate dimolybdate chelate as an end product. Activation energies were calculated as 41.4 and 49.9 kJ mol-1 for the first and zero order reactions. The fractional conversion versus time relationship can be given by the following equation.IntroductionMolybdenum is used widely in electric-electronic, metal working, aerospace and aeronautic, nuclear, glass and petrochemical industries because of its high melting temperature and resistance against chemical effects. However, the largest molybdenum consumers are the iron-steel and super alloy industries where molybdenum is used as an alloying element. Industrially important molybdenum minerals are limited to molybdenite (M0S2), powellite (CaMo04) and wulfenite (PbMo04), which are considered as primary molybdenum resources. Secondary molybdenum resources are spent catalysts and scrap [1-4].Molybdenum has been produced by pyrometallurgical processes in the past. Since it is possible to process low grade molybdenum ores and industrial wastes by hydrometallurgical processes, which are more environmentally friendly than pyrometallurgical processes, the importance of the use of hydrometallurgical processes has increased in the molybdenum production industry."

Jan 1, 2012