Search Documents

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By P. A. Olubambi1

Representative samples of the hydrothermal vein deposits of the bulk complex sulphide ore deposit, 10 km south of Ishiagu, in Ebonyin State, South Eastern part of Nigeria were collected from two small scale mining companies. The samples were mixed and successively crushed in a jaw crusher and cone crusher, and ground in a rod mill. Characterization was carried out with SEM, EDX, XRD, XRF and ICP-OES. Mineralogical analysis revealed the presence of sphalerite, galena, siderite, pyrite, quartz and chalcopyrite. X-ray Diffractometry showed that sphalerite mineral in the ore occurs as sphalerite ferrous with varied percentage of Zn and Fe within the various sizes while chalcopyrite occurs as a chalcopyrite group mineral with chemical formula Cu2MnSnS4. Results of the elemental analysis showed variations in elemental composition within the different sizes.

Jan 1, 2006

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By Jewel Andrew Gomes

Arsenic is considered as one of the toxic materials being controlled by Environmental Protection Agencies in several developed and developing countries. It is found in the nature as constituents of the soil, minerals and also in various organic forms. It enters the air, water, and land from wind-blown dust and gets into water from runoff, leaching, soil erosion and anthropogenically from chemicals used for wood preservation, insecticides, medicine, military purpose, pigments, and electronic circuitries. There are several techniques available for removal of Arsenic, such as coagulation/filtration, lime softening, ion exchange, reverse osmosis, nanofiltration, wet chemical, and electrochemical. Electrocoagulation has been found as one of the most efficient techniques to remove inorganic arsenic with more than 99% efficiency. In this paper, we present our work on electrochemical treatment of both the inorganic and organic arsenic from water using various sacrificial electrode materials, i.e., iron, aluminum, copper, and combination of them. The floc produced by this method has been also characterized using XRD, SEM/EDS, FTIR, and cyclic voltammetry.

Jan 1, 2010

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By Li Chen

A new process, i.e. Ball milling--Neural leaching--Oxidation calcinations--Chloridizing distillation--Hydrolysis, was designed to recover germanium from the vacuum furnace slag produced in Shaoguan smelter. The suitable process and operational parameters were determined for the practical production.

Jan 1, 2005

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By Jiann-Yang Hwang

Microwave heating has been proved an effective method to rapidly heat iron oxide. This offers an opportunity to apply microwave heating in the steelmaking process. The reduction reaction of iron oxide is traditionally achieved at high temperature with reducing gases such as H2 and CO generated from various sources, including coke, coal, and natural gas. This study investigates the differences in iron oxide reduction using conventional and microwave heating under H2 and CO atmospheres. A special microwave thermal gravimetric device was designed and built to facilitate the investigation. With this device, iron oxides can be heated by electric resistance heating, microwave heating, or a combination of methods. The incoming CO and/or H2 also can be preheated to simulate a potential utilization of recovered heat. The iron oxide weight and temperature can be monitored during an entire reduction period. A series of reduction experiments have been conducted. The results are presented and discussed.

Jan 1, 2006

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010