Search Documents

By Faustino G. Prado

In the, quest for an economical and environmentally friendly reclamation of metallurgical dusts generated during pyrometallurgical operations, our goal has been the separation and recovery of most of the components, as well as the complete recycle of all the reagents. Effluents have been avoided, within acceptable economic parameters. This presentation, which can be applied to a large spectrum of dusts and other residual-materials-, has focused on the dusts generated by the operation of Secondary Copper Smelters. Those dusts show a wide range of components, including zinc, lead-, copper, cadmium, tin, chlorine and-alkalies. Our present work deals with the use of ammonium salts in the separation and recovery of-the above mentioned elements in a marketable form. Most of the chemistry and techniques involved have teen already confirmed in commercial scale operations. Others have gone through pilot scale tests or bench scale tests. The recycle of reagents has also been- confirmed at the same operating levels. A preliminary evaluation indicates that the chosen route, in addition to a viable economy, offers a complete and safe reclamation within the most strict environmental regulations.

Jan 1, 1995

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Xingbin Li

A direct hydrometallurgical process of extraction molybdenum and nickel from molybdenum-nickel ore by pressure water leaching without reagent was studied. The extraction of Mo and Ni from molybdenum-nickel ore by oxygen pressure leaching, which exploit the characteristic of molybdenum-nickel minerals contain high concentration amorphous sulfide which has highly active, and make the most of easily oxide to sulfuric acid and sulfate at low temperature and excess oxygen presence of the amorphous sulfide. Under oxygen pressure conditions, considerable molybdenum and almost all the nickel were extracted into solution in the leaching process. The results show that with the leaching time for 3~4h, temperature at 150o C, liquid-to-solid ratio of 2mL/g, mineral granularity of 0.074mm, oxygen partial pressure of 0.4~0.5MPa without other reagent, molybdenum leaching percentage can be over 80% and nickel leaching percentage can be more than 97%. Furthermore, about 80% sulfur in the Mo-Ni ore has been transformed into sulfuric acid.

Jan 1, 2014

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By A. Erçin Ersundu

In the present work, three different domestic iron ores; Sivas Divrigi B Head high grade hematite lump ore, Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores reduced with Soma-Kisrakdere lignite coal to investigate their suitability for sponge iron production. A laboratory scale box furnace was used to carry out the reduction experiments. In the experimental studies different operation parameters were selected being Cfix/Fetot. ratio, temperature in the range of 1100 - 1250 oC and time, to determine their effects on metallization. Metallization degree up to 90 % was found in the reduction experiments realized by using Sivas Divrigi B Head high grade hematite lump ore, whereas for Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores 60 - 65 % metallization degrees were obtained.

Jan 1, 2008

By Marco Olper

The Italian company Engitec Impianti has developed a new electrochemical technology for the treatment of Electric Arc Furnace (EAF) flue dust generated in steel mini-mills. This process is based on a new and completely different concept from the Waeltz technology applied at present and allows, due to its modular nature, for an erection on the steel producer&apos;s site. Engitec Impianti spent US $700.000 constructing a 500 t/y throughput pilot plant at Pittini Group&apos;s Ferriere Nord mini-mill in Osoppo, Italy in order to demonstrate the process capabilities and obtain the data for a commercial plant design. The paper describes the pilot plant performances and the engineering criteria for a commercial unit of 10.000 t/y throughput. The feasibility study demonstrates a pay-back period of 3 - 4 years for the commercial plant.

Jan 1, 1995

By Tong Zhilin

The reasons why the pits were formed on the cathode in the process of Ni electrowinning and the methods how to prevent these pits from forming are described. Some examples are presented. It has &apos;been proven that P507 and P204 present in the electrolyte can effectively prevent pits from forming on the cathode.

Jan 1, 1993

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By J. P. Hager

The formation of the vapor complex AgFeC14 (g) baa been identified and its thermodynamic properties determined. The vapor pressure of silver chloride can be enhanced by a factor of 15-20 due to the formation of the vapor complex. The vapor pressure of both AgCl (g) and AgFeC14(g) were measured using a double-zone transpiration .technique. Gibbs free energies have been determined for the vapor transport reactions. Laboratory kiln tests were conducted to confirm the enhanced recovery of silver through the formation of the AgFeC14(g) vapor complex and to indicate the opportunities for process development using this new vaporization chemistry.

Jan 1, 1985

By Andreas Orth

Outokumpu Lurgi Metallurgie has developed a process for the calcination and reduction of laterite nickel ore tines where the reduction of iron and nickel to the wustite/metallic states respectively, is performed in a fluidized bed reactor using reduction gas generated very cost effectively from natural gas in an autothermal catalytic reactor. As an option coal can be used as reductant as well as additional fuel. The process of reduction and calcination is very energy optimized. It uses the off gas from the fluidized bed reduction reactor, which still contains energy, to dry and calcine the nickel ore fines in a primary stage circulating fluidized bed (CFB) reactor. The product shows high metallisation of nickel and iron oxides reduced to the wustite stage. This results in considerable energy savings in smelting the prereduced product to ferro-nickel. Alternatively the product can be leached to produce nickel. Laboratory tests showed very high recovery of nickel and cobalt. Keywords: Fluidized Bed, Prereduction, Calcination, Ferro-Nickel

Jan 1, 2004

By Huimin Lu, Lian Zhou, Panpan Wang

"For the low concentration C02 exhaust gas from coal-fired power plant, steel plant emission trapping and recycle problem, a pressure swing adsorption process was studied, using a porous imidazolate framework materials (ZIFs) as adsorbent, separating carbon dioxide from fuel gas mixture. In the carbon dioxide reduction condition by electrochemical method, using ionic liquids as electrolyte, the oxygen and carbon products could be obtained, including carbon nanotube, nano carbon fiber and amorphous carbon. At last, a new C02 collection, recycling and reuse technology was formed.IntroductionDuring the combustion of fossil fuel in coal-fired power plant or steel plant, large amount of carbon dioxide has continuously emitted into the atmosphere. The phenomenon has resulted in the melt of arctic glacier and the frequent emergence of abnormal climate. How to reduce the emission of carbon dioxide and protect human living environment has become a worldwide challenge. Recently, there are three routes to resolve this problem: The first one is to adjust the energy structure and develop new energy, such as solar, wind, hydrogen; the second one is to improve energy efficiency and avoid waste; the third one is to research capture and sequestration of carbon dioxide (CCS). But many researchers have come to realize that the recovery and utilization of carbon dioxide are more important than the sequestration of it. Because the captured carbon dioxide just buried under the earth maybe cause secondary pollution if carbon dioxide leak out from the adsorbent."

Jan 1, 2013

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002