Search Documents

By K. Watling

Vibrational spectra of surface and solution compounds formed during cyclic voltammetry of a gold electrode in a deoxygenated 0.01 mol dm-3 NaCN solution have been examined using surface-enhanced Raman scattering (SERS) spectroscopy. The presence of cyanide at the electrode surface was indicated by Raman bands characteristic of the carbon-nitrogen stretch, CN.. Chemisorption of cyanide on the gold surface was evidenced by the presence of vibrational modes due to gold-carbon stretching, AuC, and gold-carbon-nitrogen bending, AuCN. Prior to the disappearance of the surface cyanide stretch band, a limiting value of the CN was obtained, the same as the value reported for adsorbed cyanide. Effects upon the voltammetry and vibrational modes of surface species due to additions of silver and lead to the gold-cyanide system have been observed.

Jan 1, 2003

By Basant L. Tiwari

An electrolytic process, based on a three-layer concentration cell, to extract magnesium from commercial aluminum alloy scrap has been examined. The process was repeatedly tested at 1025 K with two cells of d1fferent sizes, 0.6 kg and 5 kg feed aluminum, to have a better understanding of the opera ting parameters and evaluate the scale-up potential. In both cells, the magnesium content of the scrap was selectively reduced ?from 1. 1 to less than 0.1 wt.% at anodic current dens-Hy as high as 1. 1 A/cm2 with current efficiency exceeding 85%. Magnesium was recovered in the form of salt coated globules. Comparison of performances for the two cells suggests that the process can be scaled up. With further development, this process could become a viable alternative for demagging secondary aluminum.

Jan 1, 1985

By Kaixi Jiang, Bangsheng Zhang, Lei Zhang, Haibei Wang, Xiaoping Zou

"China plays an important role in the global molybdenum industry; in fact, both China's molybdenum mine and smelter production ranked first in the world. The characteristics of China's molybdenum resources are quite complex, and moly-nickel ores with carbon, coppermoly ores and wulfenite can be only found in China. This paper firstly introduces China's molybdenum resource/ reserve situation. Secondly, the status of molybdenum smelting technologies, especially roasting by rotary kilns and multiple-hearth furnaces, are discussed. The practices and the development of some new technologies, such as pressure leaching, solvent extraction, ion exchange, carbon adsorption for moly-nickel ores and low grade molybdenite concentrates, are also introduced.IntroductionMolybdenum is widely used in special steels, aviation, alloys, chemistry, electronic and medical industries because of its excellent physical and chemical characters [1,2].In nature, molybdenum exists mainly as molybdenite associated with copper ore which are the main material for smelting. About 99% of molybdenum is produced from molybdenite. In addition, wulfenite, molybdenum oxide ore and graphite shale containing Mo-Ni have also industrial value to extract molybdenum and other metals such as Ni, Re, Pb and Zn. The reserves of molybdenum in China are about 8.4 million tons metal; China is ranked as the second largest source in the world. The output in China is more than 40 kt in 2010. Ferromolybdenum is the main product and then ammonium molybdate. The consumption in China is about 20 kt and the rest is exported to overseas.The first molybdenum smelter in China was built in 1963. Today the main producers include Jinduicheng Moly Company, Luanchuan Moly Company and Jiangxi Copper Group Company. Technologies and equipment have changed greatly. Roasting and multi-hearth furnaces are widely used. Several new processes were developed such as pressure leaching, solvent extraction, ion exchange and carbon absorption [3-8]."

Jan 1, 2012

By A. Galvan

High rate compressible media filter (CMF) tests produced exceptional total suspended solids (TSS) removal at hydraulic loading rates ranging from 97.8 to 122.2 m/h. The compressible media is manufactured from a robust resin fiber that can withstand low pH and temperatures up to 149 °C. The media porosity can be varied by applying compression onto the media. At 40% compression, the CMF can remove particles greater than 4 μ. Three synthetic test-samples were generated by Hazen Research Inc., (Golden, Colorado) to simulate the copper Pregnant Leach Solution (PLS), Raffinate and Electrolyte solutions used for the testwork conducted at their facility. The preliminary results showed that the CMF was very effective in removing TSS without the use of chemical conditioning from the above test-solutions with efficiencies of 98%, 97%, and 96%, respectively. Given the remarkably high hydraulic loading rates, the industrial equipment footprint would be minimized appreciably over conventional clarification and alternative filtration systems.

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By M. C. Nielson

The paper describes the design and operation of pulsed columns as replacements for conventional mixer/settlers. The advantages, which the columns offer, include a reduction in real estate for the plant, elimination of diluent evaporation, containment of noxious vapors and reduced crud formation. In addition to the description of operation, the paper presents the findings of laboratory tests of pulsed columns extracting copper from pregnant leach solutions and also delineates potential advantages of the pulsed column in copper solvent extraction.

Jan 1, 1999

By A. A. Bustos

Four Air Liquide Shrouded Injectors (ALSI ) were installed and operated for over one year in a Peirce-Smith converter at the Falconbridge nickel smelter in Falconbridge, Ontario, Canada. A shrouded injector consists of an inner pipe and an annulus, through which high oxygen enriched air and nitrogen flow, respectively The nitrogen cools the injector and protects the refractory in the vicinity of the injector tip, allowing for substantial increases in oxygen flow rates to the converting reactions. Several injector designs were tested to study the effect of changes in the cross-sectional area and changes in the entrance geometry of the annulus. An optimum design would minimize the injection pressure required for a given flow rate to achieve choked flow conditions at the tip of the injector. The operation of the ALSI was simple and did not require any special care or maintenance, either between blows or between converter cycles. In particular, the shrouded injectors did not require punching, as is the case with conventional tuyeres. In terms of refractory performance, the ALSI, operating at 30-40 % oxygen enrichment, were superior or equal to the conventional tuyeres, which operated at 21-23% oxygen. The results of the demonstration program led Falconbridge Limited to implement the ALSI technology on a commercial scale The paper presents the demonstration program results in terms of gas flow rates, accretion formation, punchless operation and refractory wear.

Jan 1, 1999

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns' feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns' feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln's interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns' feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004

By K. Morsi

Titanium-titanium boride whisker (TiBw) composites are emerging as strong candidate materials for advanced applications within the automotive, aerospace and defense industries. Although increasing TiBw volume fraction improves the specific stiffness and wear resistance of titanium, it is usually on the expense of fracture toughness and ductility especially at increased volume fractions of reinforcements where whiskers interlock. This research addresses strategies for microstructural design that may overcome these shortcomings, by generating titanium composites that are locally reinforced with TiBw through in-situ reaction in segregated regions of the microstructure and separated by ductile Ti matrix. The effect of varying composite reinforcement particle sizes (i.e. size of the reinforced regions) on the pressure-less sintering of these dual matrix composites is discussed. Electric current activation was also used to generate high density dual matrix composites and a new simultaneous imaging and modulus mapping technique was used to characterize these unique microstructures.

Jan 1, 2008

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By K. Dzieciol

The paper presents a study about three image correlation methods ?common cross-correlation, mutual information and phase-correlation ? applied to characterize microstructures reconstructed with X-ray tomography. It is shown that phase correlation is not only the fastest, but also the most sensitive method for detection of similar microstructure features, cavities in the present case. A new image correlation indicator is proposed, which takes into account both the phase shift and the amplitude of similar features in compared images. Some preprocessing aspects related to the tomographic reconstruction and filtering out of characteristic noise are also discussed.

Jan 1, 2009

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By K. Soldenhoff

The Bulong deposit, situated near Kalgoorlie in Western Australia and owned by Resolute Limited, is a lateritic deposit containing on average 1.1% nickel and 0.09% cobalt. A process has been developed and tested at the mini-plant scale for direct solvent extraction and separation of Co and Ni from solutions derived by acid pressure leaching of Bulong ore. In this paper, two solvent extraction processes are described. The first process uses Cyanex 272 to extract cobalt and reject nickel to the raffinate. The second process uses Versatic 10 to extract and purify nickel. The loaded strip nickel solution is suitable for electrowinning. Results of both batch laboratory tests and continuous mini-plant trials are presented. The selectivity of the solvents with respect to the major impurities such as Mn, Mg, Ca, and Zn is also discussed.

Jan 1, 1998

By K. Knuutila

The behaviour of thiourea, animal glue and chloride ions in the electro¬lysis of copper has been investigated by various different electrochemical experiments, i.e. polarization curves with stationary copper electrodes, long-time galvanostatic electrolyses and Hull cell experiments. Polarization curves with stationary copper electrodes show that animal glue has a polarizative effect on the deposition potential. Small thiourea contents affect depolarizatively when high concentrations retard the copper deposition. The microstructures of the deposited copper after the long-time electrolyses show that animal glue favours a basis oriented deposition structure. With thiourea the field orientated structure was evident. It was also observed that the deposited structure depended much on the grain structure of the starter sheet. The chloride ion concentration has a drastic effect on. the crystal size of the deposited copper as it was found out in Hull cell tests. Chloride ions flattened the the crystals and the deposition became smoother when the chloride ions were added. The cathode copper quality is discussed according to the literature. Special attention is paid on the codeposition of thiourea and the origin of sulphur impurities in copper cathodes.

Jan 1, 1987

By K. Abe

Onahama Smelter has two green-charge reverberatory furnaces and the annual smelting capacity is 600 thousand tons copper concentrate. In addition to the concentrate, various kind of industrial wastes has been processed and utilized. First, the brick waste from converter is ground and used as raw material of castable for repairing the copper melt launders. Second, the slag containing calcium-sulfide from other foundry is fed to the reverberatory furnaces. Calcium sulfide is oxidized to CaO. The melting rate of concentrate is accelenlled and the slag loss is decreased. Third, the tip tire made of waste car tire is charged into the reverberatory furnaces as fuel. The steam of waste heat boiler for turbine generators has been increased so as to decrease the electricity cost. Fourth, the sulfur accretion from other chemical plant is blended into the copper concentrate and the sulfur is recovered as the gypsum for sale. Fifth, the processed waste oil has been utilized in the copper concentrate dryer by which the smelting capacity was increased effectively. Consequently, Onahama smelter contributes to the society by processing the wastes to the harmless slag and utilizing them as fuel through the copper smelting.

Jan 1, 1996

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by 'its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340° C by the two probe method using an ultra high resistance meter. The II: value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it monotonically increased from 10-5 to 10-4 (omega) 1cm-4 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the II: value. The II: value increased with the increase of Na proportion in the melt. For a 10 mol% Na doped sulfur melt it was as high as max. ~30 (omega) 1cm-1 above 180°C under the irradiation of ultrasonics.

Jan 1, 2003

By Shujian Jia, Mingming Song, Gaoyang Song, Bo Song, Yuhou Yang

An innovative method is investigated to separate inclusion particles from liquid metal by super gravity. To make clear the characteristics of the inclusion separation, Al melt containing MgAl2O4 particles with diameters less than 150 μm has been treated under various super-gravity fields. The thickness of particle-accumulated layer formed at the bottom of the sample and the area fraction, number density and size of inclusions were measured. It is found that the thickness of the particle-accumulated layer decreases and the area fraction of particles at this location increases with the increase of super-gravity field. With the gravity coefficient G=500, time t=2 min, and temperature T=1023 K, it is hardly to find any solid particles in the upper and middle areas of the sample and the separation efficiency is up to 90%.

Jan 1, 2015