Search Documents

By T. J. McMahon

This Bureau of Mines study describes the development of a large-scale, three-dimensional, finite-element model of a deep-vein Coeur d?Alene District mine. The three-dimensional model was prepared from combined digitized mine maps and generated levels that may also be analyzed as independent two-dimensional models. A comparison of the stress changes and displacements was made following a simulated vein excavation in both the three-dimensional and two-dimensional models. A one-cut excavation was simulated with the two-dimensional model and a multiple-cut excavation was simulated with the three-dimensional model. The compared results from the two analyses are discussed in terms of the inherent differences between the models.

Jan 1, 1989

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By Denise Müller, Axel Preusse

"Due to multilateral underground use, mining subsidence is discussed more and more with regard to issues other than mining, such as post-mining topics, storage, or geothermal use. These discussions and the influence of the energy policy is why the situation in Germany is described as a transition from active to abandoned mining. Many PhD theses have been written within the last 20 years—every single one with a different topic but all with the same issue—the effects and challenges of mining subsidence.These challenges start with the research regarding geological and hydrogeological conditions, which is the basis for calculations like the angle of draw or predictions of subsidence due to water table drawdown. Furthermore, the research investigates issues like risk-management and financial planning. One of these issues is post-mining calculations; others include potential hazards of storage or the use of geothermal energy.This paper outlines an overview of German mining and the consequences due to subsidence. It deals with an overview of the circumstances related to hard coal mining, lignite mining, the use of geothermal energy, gas, and opportunities regarding underground storage. Basically, it describes the essential steps of processing mining subsidence, starting with monitoring to forecast and up to safety measures.With a glance back to the applied research of the prior two decades, we compare given forecasts with experiences already gained.Even though mining decreases, ground control does not.INTRODUCTIONAfter the Second World War, an economic recovery started in Germany, during which the mining industry provided an advantage. Areas like the Ruhr District or Saarland were characterized by hard coal mining. In addition, there was lignite mining in the Rhenish mining area and the middle German coal district. In the Lausitz area, there were gravel and sand companies for the construction industry and many other medium-sized mining companies. Especially in the Ruhr District and in Saarland, where large coal fields were built, mining played a major role. The number of mines increased, and the negative effects on the terrain got bigger. While minor open pits or quarries have influences on the landscape only, large open pits and underground mining lead to significant ground movements. This results in a larger importance of mining subsidence engineering. Calculations of subsidence and forecasts have been developed and refined within the last several years. Due to the fact that the mining areas were and still are densely populated, the forecasts are getting more and more precise."

Jan 1, 2018

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By John Magyar

Special foamed cements were used to stabilize and secure caving ground in a newly-reamed 12.5-ft diameter underground ventilation raise. Two zones of very poor Rock Mass Rating (RMR) material were encountered during reaming of a ventilation raise at Placer Dome's Turquoise Ridge Mime in Northern Nevada These zones caved to large cavities, continued failing, and could not be safely secured using standard rock bolting, wire mesh, and shotcrete procedures. In stable sections of the raise, the ground control plan called for the contractor to install 8-ft and 124 length resin grouted No. 7 Dywidag bolts, chain-link fence mesh and shotcrete. This work was conducted on three decks installed on the raise bore reamer. The first of the caved areas was approximately 1,500 cubic yards in volume and extended out to 40 ft beyond the wall of the raise. Placer Dome considered several options for structural fill to repair the area including pumped shotcrete, concrete, and placing and grouting aggregate. A safe, cost effective, and expedient method of stabilizing the raise with foaming grout and bolted liner plate was selected and successfully executed. The special fast-setting, foaming cement grouts used were Tekfoam and Tekseal® manufactured by Minova. The raise was quickly placed in service. Factors considered in selecting the foaming grout are discussed.

Jan 1, 2005

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Jun Lu

The Pittsburgh seam is the most extensively mined coal bed in the Appalachian Basin. Unlike most other prominent coal seams, the Pittsburgh seam typically includes a sequence of immediate roof coals and intervening rock binders (or ?draw slate?), most of which are within mineable horizons. Furthermore, unlike the main bench, the thickness of the overlying roof coals and their intervening rock binders can vary significantly. For instance, in southwestern Pennsylvania, the Pittsburgh seam main bench typically ranges from about 5.0 to 6.0 feet thick with minimal variation over short distances. On the other hand, the Pittsburgh seam roof coals and immediate roof binder typically range from a few inches to several feet, and in certain geologic settings can vary significantly over short distances. Additionally, in some locations, very thick draw slate can totally replace the roof coals. Since the draw slate, which typically consists of claystone or clayladen shale, is relatively weak, the presence of thick and variable draw slate in the roof and rib can significantly affect mine safety and productivity. This paper presents the adverse effect of thick draw slate on a 1500-foot-wide longwall face in a southwestern Pennsylvania coal mine. Mapping of the thick draw slate, numerical models which illustrate stress distribution and failure associated with thick draw slate, and operational adjustments instituted to mitigate the negative impact of thick draw slate will be discussed in detail.

Jan 1, 2013

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Yundong Ma

In this paper the dynamic process of rock deformation and failure in the roadways of the #9 coal seam, Wuhushan Coal Mine by was simulated using the software "Rock Failure Process Analysis System (REPA)" [I]. Based on the simulation results, this paper analyzes the failure process, characteristics and weighting of the overburden as the longwall retreat mining proceeds. The roadway's behavior including deformation characteristics, failure mechanisms, stress distribution in the surrounding rocks and the effects of various support systems on roadway stability were analyzed and studied. While simulating the rock failure process with REPA, the model stresses can be obtained through two approaches: (1) the stress is reflected by the grayscale of pictures in the model failure process and (2) the model stress can be obtained by muti-element information, which is one of the commands in RFPA system. Data files of stress can automatically be created, and curves of stress and displacement of each element can be displayed in each step of computation. Keywords: Rock Failure Process Analysis System (RFPA); roof control; roof to floor convergence; combined support

Jan 1, 2005

By Alexandra Garcia

A measurement-based ground control management system, commonly employed in coal mines, has been successfully implemented in a UK potash mine operating at a depth of over 800 m. This system includes the routine deployment of telltales in roadways throughout the mine to mitigate against the risk of large-scale roof falls and the deployment of detailed ?design monitoring? instrumentation for ongoing design verification. The routine monitoring systems used in coal mines have not been, to date, commonly applied in potash mines, despite the similar, variable weak geology and associated ground control hazards. Monitoring information from the site indicates that telltales can be deployed to monitor roof conditions, with action levels based on differential rates of strain, as opposed to absolute movement.

Jan 1, 2014

By Kazem Oraee-Mirzamani, Nikzad Oraee-Mirzamani, Arash Goodarzi

"Unexpected movement of ground can potentially endanger lives, damage equipment or destroy property. Occupational accidents frequently occur with fatal consequences in developing countries with significant economic dependence on industries such as mining. Therefore, there is increasing need for miners' protection against such hazards. Slope stability and roof support accidents are two of the major causes of fatalities at surface and underground mining operations. According to national codes, employers are obligated to protect workers against accidents; however, these rules fall short of the standards in developed countries. National safety regulations should clearly specify support systems. The International Labor Organization (ILO) prepared two codes of practice, aiming to guide those responsible for improving standards of safety and to provide guidelines for drafting of safety regulations for the coal mine industry and quarry open cast mines. The practical recommendations of these codes in the ground control area have been analysed and the advantages and disadvantages of ILO codes concerning ground control are summarized.INTRODUCTIONTwo million people die every year from work-related accidents and diseases. An estimated 160 million people suffer from work-related diseases, and there are an estimated 270 million fatal and non-fatal work-related accidents per year. In economic terms, the ILO has estimated that 4% of the world's annual GDP is lost as a consequence of occupational diseases and accidents (ILO, 2009).Mining has always been dangerous due to many potential risks such as those associated with using machinery in enclosed spaces, rock falls, blasting operations and explosion of flammable gases, which endanger miners' safety and health. However, it is suggested that implementing new laws along with strict adherence would reduce such risks in the workplace.The severity and frequency of accidents are trending downward in developed countries, where the focus is on large private companies who invest heavily in mechanization and developing economies of scale. But in many parts of the world, particularly in developing countries, minerals are extracted by people working with simple tools and equipment; they work on a smaller scale, are more flexible, and can exploit irregular ore bodies and steep, dipping seams."

Jan 1, 2010

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Anthony Lannacchione

There has been a persistent need to forecast roof falls so that miner's exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected .from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

Jan 1, 2005

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Marcel0 Mondring

Transportation and the logistic requirements are set very high for the German coal mining industry. Short transportation resources, crowded quarters, and long transportation distances to destinations are some basic conditions that logistic employees of the mines have to deal with. Therefore, in the context of these processes, human effort and technology are faced with great challenges. There can be a total of 300 transport units, depending on the size of the mine. Every day, they are moved through a nearby 150-km-long transportation network of floor and monorail tracks. Of these transport units, 150 are new, and the other 150 units are split into cross traffic units that are moved only in the underground and return travel units. Beside track-bounded transports, all material transports take place in the shaft. As a result, many involuntary transports and changes in the means of transportation make the daily work more difficult. Typical transports in the shaft include the supply of new materials from above to below, as well as returnable goods from below to above. Cross traffics throughout several levels, which are rather rare, would have to be handled above the shaft. Due to limited shaft capacity, these cross traffics should be avoided when possible. Based on the gas resources in coalmine slopes, track-bounded transports using monorails (powered by diesel or rechargeable means) are preferred. This depends on the road degree, the depth, and track cross section of the shaft/slope. The variety of the material spectrum includes more than 100,000 different types of material.

Jan 1, 2014

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By J. F. T. Agapito

Overcore measurements at the North Fork Valley (NFV) coal mines in western Colorado have shown that horizontal stresses are highly anisotropic. Measurements have been made in four mines at various depths. In many measurements, the maximum horizontal stress is three to four times higher than the minor horizontal stress. At the West Elk Mine, maximum and minimum horizontal stresses of 24 MPa and 6 MPa, respectively, have been measured at depths of 640 meters (m). Under highly anisotropic stress conditions, ground control problems associated with both high and low horizontal stresses can develop. While high horizontal stresses can produce cutter failures and floor heave, low horizontal stresses can allow block fallouts. This paper summarizes the horizontal stress measurements in NFV mines and, in particular, in the West Elk Mine where their role in roof fall and floor heave failures is discussed. This experience has led to an improved use of ground support and safer mining operations at depths of 640 to 700 m.

Jan 1, 2005