Search Documents

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as 'spin to stall.' The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to 'spin' and 'wait' times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By B. G. D. Smart

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

By J. G. Stewart

Polyurethane injection for the consolidation and control of broken strata is a common practice in the deep mines in Europe. The technology has gained wide acceptance in the coal mines of America since the introduction of RokLok polyurethane binder by Mobay Chemical Corporation in 1977. A popular and growing use for polyurethane consolidation grouting is to control the roof and prevent gob flushing during recovery of longwall face equipment. The technique provides many time and performance-related benefits compared to more conventional methods using wire mesh. Kitt Energy Corporation installed the nation's first 1000-feat longwall face in April and May of 1984. The face completed the first panel in October, 1984, and recovery was begun. Roof Strata consolidation for the recovery was accomplished by a RokLok polyurethane binder infection program designed and supervised by Halbach & Braun Industries. The application provided the most rigorous and demanding test to date of this method's performance and cost-effectiveness relative to bolts and wire screen.

Jan 1, 1984

By E. Bane Kroeger

Rib failure is a hazard that has resulted in many injuries and fatalities in underground coal mines, especially in soft coal seams. Conventional rib control methods including rib boarding, shotcreting. steel meshing and geogridding, are fairly expensive and time consuming to install. Some methods, such as rib boarding, have met with marginal success at controlling rib failure. Under this research, the Rib Strap System (RSS) introduced by Dr. Chugh in 1999, was modified and new components were added. Both bench scale and full size prototypes were tested in the labs at SIUC to determine the best materials for fabrication and easier methods for assembly and installation. This laboratory research has developed new methods of securing the strap ends to smaller rib hoards, a new device to post-tension two straps together, and a technique for replacing straps without having to drill new rib bolts or for retrofitting straps to rib hoards that are already in place. The method used to secure the strap end to rib boards developed during bench-scale testing was dubbed the wrapped staple technique. It is very simple, requiring only 10-15 staples, with the end of a strap secured to a rib board in about 45 seconds. Several different prototype designs for a new device to join the strap ends together and tension the strap were fabricated and tested in the labs at SIUC. The device, dubbed the rib strap buckle, was very easy to install and held the straps firmly. One specific buckle design worked extremely well during testing and exceeded all expectations. The laboratory research also developed a method of replacing a damaged rib strap that can also be used to add rib straps to existing rib boards. The technique uses nails, spacer blocks, and band clamps to secure the new board and strap. This technique was developed to allow one person to replace a strap using only a hammer and screwdriver, negating the need to drill and install a new rib bolt using mine equipment such as a roof bolter or scoop. In addition to the technical feasibility, the cost of materials for the rib strap system was compared to the rib boarding method currently being used at a mine in the Illinois Basin. The mine is using 20 rib boards on each pillar at cost of about $223.60. The costs for the rib strap system depend on the materials chosen for fabrication but for the base case, were about $97 per pillar.

Jan 1, 2004

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Changshou Sun

Excessive deformation occurred in the underground openings of Jinchuan Nickel Mine, the largest nonferrous underground mine in China. Developed in weak rock formations at great depth, the underground openings are under great in-situ stresses with the horizontal stress being twice as high as the vertical one. Based on in-mine observations and in-situ testing results at the mine, time-dependent mite element simulations with coupled creep and plasticity constitutive models were conducted in this study to analyze the stability of underground openings In the study, the Burgers creep model and the Drucker-Prager plastic model were coupled to simulate underground drifts and cut-and-fill stopes. Two-dimensional finite element models were developed with ABAQUS - a comprehensive finite element simulation package The study investigated the behavior of underground drifts at great depth with high horizontal stress and the behavior of cut-and-fill stopes with various stope heights and fill conditions. The numerical simulations revealed important characteristics of opening deformations as a function of time after excavation and location relative to the wall of opening The results had good agreement with field monitoring data, They provided useful information to aid mine engineers in the design of mine openings, the selection of opening supports and the determination of support installation procedures.

Jan 1, 1999

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984

By Y. Luo

An extensive subsidence research program conducted by the authors has greatly improved the accuracy and the capabilities of subsidence prediction under complicated mining and surface conditions. The techniques developed for assessing and mitigating subsidence influences on various surface structures have been applied in numerous cases with a very good re- cord of success.

Jan 1, 1997

By D. J. Reddish

This paper illustrates how numerical modelling has been utilised to predict water and gas pathways around active longwall panels using two case studies. This information has proved invaluable m the design of methane drainage schemes and for risk assessments undertaken at the mining planning stage. The modelling approach described has now been applied successfully to several situations in UK coalmines in order to optimise the position, length and orientation of methane drainage boreholes. The first case study describes the numerical modelling of the stress and shear plane development mund a longwall panel. The simulation was used to predict potential gas pathways through regions of low stress confinrment which are conducive to fluid flow. The conclusions from the modelling were utilised to allow an increase in the volumes of gas drainage and allow the efficient mining of the panel. A detailed discussion is provided on the model construction, determination of input paramters and optimisation of the borehole positions Details are provided on how the models allow a prediction of the fracture patterns, stress distributions and zones of reduced permeability around an active longwall panel. The second case study describes the numerical modelling of a fault adjacent to a face line drivage of a panel that had just started to be retreated. An inrush of water had occurred and a concern was whether further mining would lead to more extensive inrushes or whether the water inrush was associated with more local, limited capacity water bearing features. The role of a fault that was positioned close to the locality of the mine workings was examined. Fracture patterns stresses, strata permeability and water flows were predicted using mechanical and hydro-mechanical coupled models.

Jan 1, 2003

By Dieter Wittenberg

The use of thc ultrasound technique for monitoring rockbolt support has at last provided support engineers with a measunng system capable of pinpointing fracture failuns in fully-grouted rockbolts. The measurement data are based on the operatmg characteristics of the bolt type, which are determined both under test-bench conditions (DIN 21521) as well as in underground trials. Practical experience acquired to date suggests that this new measuring system is both effective and reliable.

Jan 1, 2001

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By Mohummad Akram

Statistical analysis of multi-seam mining case studies demonstrated that geologic structure and lithological type and sequencing were predominant factors in entry failures. Finite element analysis was used to evaluate the effects of stress field changes on entry instability under differing geologic conditions. Analysis showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Effects of external support on roof stability were examined. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research design, criteria were developed for roof stability evaluation under specified interactive loading conditions.

Jan 1, 1993

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003

This paper describes the experiences with the application of the Coal Mining Roof Rating (CMRR) System to South African strata conditions. Roof classification studies using the CMRR system were undertaken as part of a SIMRAC investigation into falls of ground in South Mean collieries. Colliery roof rating exercises were undertaking in a range of geotechnical conditions from shallow level coal seams under flat topography to workings with cover depths of greater than 300m A comparison is made between the CMRR and other Rock Mass Rating systems used to classify different roof geotechnical conditions. The need for geological discontinuity orientation, blasting and rockmass stress adjustments to the CMRR is discussed. The effects of acid mine water on strata weatherability and the need to incorporate immersion tests using acid mine water are also detailed. In addition limited correlation is given between CMRR values and other geotechnical factors such as joint trace length, joint shear strength, joint orientation, weatherability and roof damage due to horizontal stress. Taking cognizance of these observations, a concept of stress induced roof damage triggering is discussed.

Jan 1, 2001

By M. Bouteldja

A finite element modelling approach is developed for the evaluation of the mechanical performance of cable bolts supports in underground mine structures. The modelling approach permits the simulation of any arbitrary number or pattern of cable bolts, that can be either partially or fully grouted, with or without end plates. The modelling technique used treats each cable bolt as a set of bar elements representing the steel cable. The bond stiffness characteristics of the grout bolt interface are represented by shear springs uniformly distributed along the cable length. Coupled with a simple linear elastic analysis, this technique can serve as a dedicated numerical model for cable bolted excavations. The application of the model is illustrated with two case studies: one for a hard rock mine and another for a coal mine.

Jan 1, 1999

By Xu Linsheng

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including modelling.

Jan 1, 1992

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By Stephen P. Signer

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In sonic cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20.000 microstrain. However, electrical continuity to many gages was lost, and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

Jan 1, 1998

By Song Yong Jin

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts, collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger.

Jan 1, 1992