Search Documents

By Sandin Phillipson

During the course of ground control evaluations conducted by the Mine Safety and Health Administration's Roof Control Division, a number of surface and underground coal mines were visited that exhibited instances of ground failure associated with joints. The evaluations were conducted over a broad geographic area, including the Appalachian Basin from Pennsylvania to Tennessee, and they documented that joints occur in a wide variety of mining conditions and exhibit a wide variety of characteristics. Despite minor local variability in orientations, the joints fit into a cohesive pattern when evaluated on a regional scale in context with the system of thrust faults that define the Alleghany Front. Joints documented for this study, together with joints in sandstone and coal and the trends of drag folds compiled from other studies, were plotted on regional maps using GIS software. The trends of joints, including those that could be described colloquially as "hill seams," were not only parallel to regional fault systems and local trends of drag folds, but were also parallel to the regional patterns of previously mapped joints in sandstone and coal. These observations indicate that the features referred to informally as "hill seams" are in fact joints formed in response to tectonic processes associated with regional deformation of the Cumberland-Allegheny Plateau. The 286-266 million-year-old age of regional deformation significantly pre-dates the time when the Cumberland-Allegheny Plateau was subjected to deeply incised stream valley erosion, which began 25 million years ago. This challenges an existing interpretation that "hill seams" represent local ·stress relief joints that formed when stream valley erosion removed confinement and allowed tensile failure of the rock. Although relaxation of confining stress can reasonably be expected to occur near outcrop, observations indicate that this results in the dilation of existing joints. This paper presents instances of ground failure associated with joints, discusses methods of mitigation, and recommends that the term "hill seam" be abandoned in technical communication because it simply refers to a kind of joint that may exhibit certain weathering and aperture characteristics.

Jan 1, 2010

By Denise Weber, Jürgen Kateloe, Marku Papst, Laurenz Preusse, Axel Preusse

"The angle of draw (in Germany, referred to as Limit Angle) plays a significant role in the field of mining subsidence engineering. This applies both to the assessment of the affected area by underground mining activities as well as applied methods for the prediction of ground movements.Recent observations using remote sensing show that ground movements outside the affected area defined by the angle of draw have been detected in German hard coal mining. Since the affected area by underground mining activities also plays an essential role regarding claims of landowners with damages to their houses and infrastructures, possible solutions for limiting the size of the affected area will be presented in this paper.Ground movements which exceed the affected area of an underground coal mine, as defined by the angle of draw will be shown in an exemplary manner. Present knowledge indicates an expectation that ground movements outside the affected area will not cause damage of major significance.This paper outlines the consequences for all affected parties regarding ground movements due to underground coal mining that exceed the extent of the area defined by the currently assumed angle of draw. This will be visualized in a case study.INTRODUCTIONGermany has a long tradition of coal mining, especially in the mining area of the Ruhr district. Following a long period of mining activity, the area is now highly populated and densely developed. In such an environment, it is of utmost importance to calculate and predict ground movements initiated by mining activities; therefore, the research here focused on the prediction of ground movement for the last decades. Special attention was given to the development of accurate ground movement models, which can be utilized in all mining areas. These models are based on different influencing factors such as depth of mining, worked thickness and the angle of draw.Depending on these models, the mining companies calculate the area of land subsidence; the predicted results are used for financial calculations and planning. For structures on top of zones with a high risk of deformation, structural measures can be applied, construction warnings can be given and, in cases of damage, compensation can be planned. The technical and economic planning was performed for all areas of mining subsidence. The most important factor for the outer limits of mining subsidence is the angle of draw (Ger. Grenzwinkel), which plots the border of the area of mining subsidence."

Jan 1, 2015

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By P. Palmer

Using 3D numerical modeling as a tool to predict rock behavior during mining extraction is still an uncommon practice at many underground operations. This paper will discuss how 3D numerical models were used to identify potential underground instability problems in the later stages of mining. Detailed modeling was then used to make modifications to the mine design in order to minimize the impact of the potential instability problems. This paper will also discusses how the back analysis of a previous underground collapse event at the same mine in a room and pillar area was used to identify the instability problems for a new orebody being developed deeper in the mine. A 3D numerical model was first created in the MAP3D software to determine the conditions of the pillars and the magnitude of the vertical displacement above the mining zone prior to the underground collapse. The results from the ground collapse model were then used as a threshold limit for predicting potential instabilities and developing a model for the new mining zone. sing the results from this analysis, mine management has been able to implement a much higher percentage recovery of the reserve in a new, high-grade area of the orebody while minimizing potential instabilities in the future.

Jan 1, 2005

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Daniel Su

Following several roof falls in the E3 longwall development of a Consol Pennsylvania Coal Company underground coal mine, an underground roof geology reconnaissance program consisting of twenty-nine 20-foot deep roof holes had identified the presence of thick sandstone layers with abundant shale and micaceous streaks. The base of the sandstone was 4 to 8 feet above the roof line within the fall areas. The presence of micaceous streaks created extremely pronounced planes of weakness in the sandstone. A structural irregularity, which extends into the E4 and E5 developments, exists between crosscuts I 1 and 30,where all roof falls occurred. Immediately to the east of this structural irregularity lies a huge syncline. The presence of thick sandstone units within the typically all shale environment and within such a structural irregularity helps to maximize stress concentration and creates closely spaced joints in the sandstone, which explains why many cracks are present in the macroscopically massive sandstone upon development. The approaching E2 longwall gob to the south and on the down-dip side, on the other hand, provided horizontal stress relief in the sandstone, which helps to explain the many roof falls in the E3 development that occurred during or immediately after the formation of the E2 gob. Finite element modeling confirmed the presence of such horizontal stress relief. Since the E3 longwall was a right-handed face, stress concentration was expected at the longwall headgate T -junctions, and further delamination of the sandstone was expected upon arrival of the E3 longwall face. Based on the results of the roof geology reconnaissance program and a roof stability analysis that took into account up to eleven parameters, supplemental headgate and track roof support consisting of 16-foot and 20-foot long cable bolts was successfully implemented within the zone of thick sandstone with micaceous streaks and structural irregularity and at other potential roof instability areas along the E3 development. The cable bolts were designed to be anchored at least 4 feet above the sandstone unit into the mostly competent sandy shale layers. No headgate roof control problem was reported within the sandstone and structural irregularity zone during E3 and the subsequent E4 longwall extractions.

Jan 1, 2002

By Ihsan B. Tulu, David F. Gearhart, Gabriel S. Esterhuizen

"Ground deformation and support response was monitored in a longwall gateroad as part of a research project into gateroad stability under changing loading conditions. In this study, instrumentation was installed in a gateroad located between two active longwall panels. The first panel to pass was the second panel in the district, and the second panel to pass the instrumentation sites was the third panel in the district. All of the panels in the district were right-handed. All of the instrumentation was installed in the number one entry, the tailgate, the second panel to pass the instrumentation sites at a mid-pillar location, and at an outby intersection location under about 600 feet of cover. The instrumentation included roof extensometers, cable bolt load cells, hollow inclusion cells, borehole pressure cells, standing support load cells, and convergence sensors, and a multipoint borehole extensometer. The roof extensometers measured roof convergence and sag. The cable bolt load cells measured the roof load applied to the cable bolts in the secondary support array. Hollow inclusion cells measured the magnitude and direction of the principal and shear stresses. The borehole pressure cells measured the stress on a pillar in the entry nearest to the second panel to pass the instrument site. The instrumented wood cribs in the entry nearest the second panel recorded the closure and load on the cribs, and the multipoint borehole extensometer in a pillar closest to the second panel recorded the location and width of cracks that occurred and total expansion of the pillar. This paper describes the effects of the changing stress caused by the first panel as it approached and passed the locations of the instruments on the opposite side of the gateroad system and the later effect caused by the second panel as it approached and passed the mid-pillar instrument location. The first panel passing caused significant loading at the mid-pillar instrument location, but not at the intersection location, while the second panel had passed the mid-pillar location and just arrived at the intersection location when the dataloggers needed to be removed."

Jan 1, 2017

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By Daniel W. H. Su

This paper presents a retrospective assessment of ground control research and its successful application by CONSOL Energy over the past 25 years. Recognizing the need to improve the understanding of coal pillar design mechanics under shallow, medium, and deep covers, an extensive underground coal pillar instrumentation program was initiated in the mid 1980s. Combined with sophisticated numerical modeling technique and laboratory tests, results from this instrumentation program were used to advance the concept of coal pillar design and to demonstrate that numerical modeling can be used to predict in situ coal pillar strength, especially under non-ideal conditions where interface friction and roof and floor deformation are the primary controlling factors. To evaluate the impact of longwall mining, a 10-year subsidence research program was initiated in 1986 that encompassed surface, subsurface, and underground measurements, as well as a sophisticated numerical modeling technique. Results from the research revealed that interface friction and shearing between rock layers within the overburden had a profound effect on surface subsidence development and the resulting strain. Recognizing the impact of horizontal stresses on CONSOL?s mining operations, extensive horizontal stress measurements were conducted using the USBM Borehole Deformation Gage and the CSIRO Mininfrac system in the mid to late 80s. Roof extensometers and CSIRO HI Cells were used to measure roof displacement and roof stress concentration in longwall headgates and tailgates, which resulted in the definition of right-hand and left-hand longwall panels. Pillar design modifications, combined with cable bolt application and innovative standing support installation, were then successfully employed to mitigate horizontal stress impact on the right-hand longwall headgates and left-hand longwall tailgates. An in-house floor bearing capacity test apparatus was fabricated and employed underground to determine mine-specific floor bearing capacities which, along with other geotechnical parameters, were then used in the mine-specific shield design. To promote caving of thick, massive sandstone immediately behind longwall face supports and to improve face conditions, the hydraulic fracturing technique was successfully employed by CONSOL to pre-fracture the sandstone prior to longwall mining. Face monitoring and numerical modeling confirmed the effectiveness of the hydraulic fracturing technique. A roof geology reconnaissance program was initiated by CONSOL in the early 1990s to improve roof control, safety, and production. Information obtained from the reconnaissance program was used successfully to guide mine planning decisions and daily roof support practices.

Jan 1, 2011

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Liu Xiao, Lin Xiaoying, Ma Geng, Tao Yunqi

"The soft coal in China has several issues, low permeability, high gas content and prone to gas outburst, making it difficult to drill and improve its permeability. Using the rock mass loading test, the relationship of stress-strain-permeability-time of sandstone was investigated. The fracture network that communicates with coal seams to provide the pathways for gas migration can be established by drilling, hydraulic fracturing or loose blasting in the roof and floor about 5m from coal seams top and bottom. The gas migration can be summed up as ""desorption-diffusion-two levels of seepage"" for gas drainage of the quasi-protection-layer in hard coal seams, and ""desorption-two levels of diffusion-seepage"" in soft coal seams. In the quasi-protection-layer, different gas drainage techniques were used during different stages of mining. Gas drainage of the quasi-protection-layers was demonstrated at Hebi Zhongtai Mining Co., Ltd. The results showed that the technique promotes the gas seepage flow, and improves the efficiency of drainage. The influence zone of the quasi-protection-layer was 1601 m2 and the average amount of gas drainage was 328m3/d, with the maximum being 661m3/d. INTRODUCTIONGas is one of the main factors that cause disasters and influence safety production in underground coal mines (SACMS, 2009). The coal-bearing formations in China have been subjected to multiphase tectonic stress field during the period of geological evolution. Coal body was often crushed into fragmented coals and mylonitic coals under the tectonic stresses (Su and Lin, 2009). The gas permeability of coal is generally poor. So in underground, drilling and hydro-fracturing technology have been used to improve the permeability of coal, such as intensive drilling, hydraulic punching, hydraulic cutting, hydraulic extrusion and deep hole blasting. But the gas drainage rate was low, only 23% (Liu, Li, and Li, 2006; Li and Wei, 2006; Henan Polytechnic University, 2008; Ma, et al., 2014; Lin and Wu, 2009; Zhou, et al., 2011) that was much lower than the rates achieved in the main coal-producing countries such as America and Australia whose average rate of gas drainage was 50%. The protection layer mining technology has been used widely as an effective technique to improve the permeability of coal in the mining of multiple coal seams (Cheng and Yu, 2003; Diaz and Gonzalez, 2007; Karacan, et al., 2007; Palchik, 2003; Latham, et al., 2013; Yuan, et al., 2013; Shi and Liu, 2007; Wang, et al., 2008, Guo, et al., 2015; Lu, et al., 2015; Slazak, Obracaj, and Swolkien, 2014 ). In the single low permeability coal seam, there is no protection layer. This kind of coal seam has low permeability, high gas content, soft coal body, and is prone to serious gas outbursts. During drilling, the holes very often spray, collapse, stuck and wedged the drilling tool. The hole length drilled is difficult to reach the required minimum, the service life of holes for gas drainage is short, the construction cost is high, and the holes are difficult to maintain. The gas drainage efficiency of single low permeability coal seam, especially soft coal seams, cannot be improved even though hydro-fracture technology has been implemented, because its permeability is not improved."

Jan 1, 2016