Search Documents

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By Susanne Pignolet-Brandom

Flash smelting products of a copper sulfide concentrate collected at successive levels in an experimental reactor have been studied by reflected light microscopy, scanning electron microscope - energy dispersive analysis and electron nicroprobe analysis. Chalcopyrite, intermediate solid solution, bornite, chalcocite, metallic copper, magnetite, iron-copper spinel, pyrrhotite, hematite, delafossite and cuprite have been identified in the product samples. The detailed reflected light microscopy study of these phases and their abundance in the samples has resulted in the identification of the series of reactions during flash smelting.

Jan 1, 1985

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon' as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far and at the same time improves the performance characteristics.

Jan 1, 1977

By J. R. Hoskins

Method - A direct approach to instrument users, initially by letter and later by telephone or personal contact was made. The resultant data was compiled to give specific use information on the seven instruments. During the course of the study attempts to evaluate the Griswold Gage were abandoned when it became apparent that the gage was not being commercially produced. One company is developing the gage for its own use. The information presented is the result of over 1200 inquiries.

Jan 1, 1973

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By E. A. Schmidt

The Thompson Creek molybdenum deposit is located in the Bayhorse mining district about 20 air miles southwest from Challis, Idaho. Cyprus Mines Corporation began exploration on the property in 1968, and at present is in the pre-production stripping phase. Molybdenum mineralization is contained in a late Cretaceous (88 m.y.), composite, biotite granodiorite-quartz monzonite intrusive complex. The complex intruded carbonaceous argillites, causing local silicification and hornfelsing of the sedimentary rocks. The main portion of the orebody is unconformably overlain by up to 1000 ft of Challis volcanic rocks (49 m.y.). Surface mineralization and related rock alteration can be recognized over a 2500- x 8000-ft area extending northwesterly from the discovery outcrop. Molybdenite occurs in a network of subparallel quartz-biotite-muscovite-orthoclase veins and veinlets within the intrusive rocks. The zone of +0.020/0 Mo mineralization outlines a steeply dipping tabular configuration in the main orebody and gradually changes into a hood-shaped configuration along strike to the northwest. The overall grade [ ] of the deposit is controlled by the abundance of the quartz- molybdenite veins and veinlets in the intrusive rock. Very little disseminated mineralization is present, and no economic mineralization occurs in the argillaceous sedimentary rocks. Muscovite, biotite, and orthoclase/microcline define three alteration zones that conform with the overall zone of mineralization. The upper alteration zone contains dominantly muscovite and sericite associated with quartz veins. The central zone contains coarse biotite and locally orthoclase and microcline. Molybdenite is most abundant within this zone. The lower zone contains thin envelopes of orthoclase/microcline around quartz veins. Based on about 313,000 ft of drilling and 8592 ft of underground development work, computer-derived ore reserve calculations indicate 200 million tons averaging 0.1 1% Mo at a 0.050/0 Mo cutoff grade with a waste to ore stripping ratio of about 3:l.

Jan 1, 2013

By T. T. Toomver

The evolution of Inco's Selective Reduction Smelting Process as practised today is described, beginning with the initial laboratory experiments on small samples to the processing of large bulk samples through pilot plant equipment. For both the Guatemalan and Indonesian (Soroako) ores, the initial screening tests using hydro-, vapo-, and pyro-metallurgical processes showed that the latter was the most promising both metallurgically and economically. Later, larger scale tests confirmed the earlier testwork.

Jan 1, 1979

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By E. H. Christiansen

The most valuable gem- quality red beryl comes from the Wah Wah Mountains of south-western Utah (Fig. 1). Red beryl occurs as a secondary mineral in topaz rhyolite. Marketable crystals from the Wah Wah Mountains have been produced from the Violet Mine, operated on a limited scale since 1976 under the ownership of the Harris family of Delta, UT. From 1989 to 1995, production from the mine amounted to more than $3 million with an inventory of several million dollars of unsold gems (Harris, 1995). In 1994, Kennecott Exploration leased the mine and surrounding claims to determine reserves and feasibility of gem recovery. Mining and exploration activity are continuing. Previous work on red beryl has dealt mainly with crystallographic, chemical and optical properties of the crystals (Shigley and Foord, 1984) with only general descriptions of the geology (Ream, 1979). However, the conditions needed for formation of red beryl have not been well constrained. It is generally proposed that beryl originates by precipitation in fractures and vugs from high-temperature gases as they are released from slowly cooled rhyolite lava. Dozens of topaz rhyolite flows and domes, similar in composition to the beryl-bearing flow in the Wah Wah Mountains, occur across the western United States (Christiansen et al., 1986). All of these flows devitrified to form vapor-phase topaz and locally other vapor-phase minerals such as bixbyite, garnet, hematite, pseudo-broo- kite and fluorite. But the occurrence of beryl is rare. Even within the rhyolite flow that hosts the red beryl, the productive open pits comprise only a small fraction of the surface area of the flow. Apparently, the conditions that favor the formation of red beryl are rarely achieved. Geologic setting The rhyolite flow that hosts the red beryl deposit lies along the eastern flank of the Wah Wah Mountains (Fig. 1). Prevolcanic rocks consist of Proterozoic, Paleozoic and Mesozoic sedimentary rocks that were folded and thrust to the east during the Sevier orogeny. Cenozoic volcanism began about 34 Ma. It consisted mostly of large volume dacitic ash flows and lesser volumes of low- silica rhyolite and andesitic lava flows. Beginning about 23 Ma, the style and composition of volcanism changed to smaller-volume, ash-flow and dome-forming eruptions of high-silica rhyolite and trachyandesitic lava. These rocks form the Blawn Formation of which the beryl-bearing rhyolite is one member (Best et al., 1987). Abbott et al. (1983) reported a K-Ar age of 22.1 + 0.8 Ma for this flow. It is probably the oldest topaz rhyolite flow in the Wah Wah Mountains. A subsequent episode (12 to 13 Ma) of bimodal magmatism produced the Steamboat Mountain Formation. The rhyolitic part of that is locally topaz-bearing. Displacement on the late Cenozoic extensional faults that formed the north-trending mountain ranges began about 22 Ma. Geology of the Violet Mine The rhyolite that hosts the red beryl deposit is part of a flowldome complex that overlies nonwelded tuff of cogenetic origin. This rhyolite is exposed over an area of about 9 km2 (3.5 sq miles) (Fig. 1). An unknown additional portion of the rhyolite is concealed beneath younger mafic lavas and sediments.

Jan 1, 1997

By Marlies Grimmer, Frank Amo Boateng

One of the challenges of mining is the concentration of heavy metals it releases into the environment through a phenomenon called Acid Mine Drainage. Freiberg is no exception due to its long mining activities. The European Union proposes that all rivers and streams must be in a good ecological status by the year 2027 but this would be difficult for large water sources as it would be economically unviable. Consequently, the approach of treating these waters at point sources would be of immense help and hence this column experiment on mine water treatment with carbon sorbents to remove zinc form the Rothschönberger Stolln. For this experiment three resins namely, APTsorb, activated coke, charred fermentation residues (which was produced by the Freiberg University of Mining and Technology) were analyzed through a simple column experiment to determine their sorption capacities. Through their sorption capacity as this experiment seeks to ascertain: we are able to make suggestions scientifically on the best material among the three for the future design of a treatment plant for the RSS. After the experiment whereby a 10 ml peri glass column was used, material A: APTsorb showed the least adsorption capacity (0.01 meq/g) and this could be attributed to the fact that the resin works well under pre-determined parameters such as pH and surface area. Material B: Activated coke showed a better sorption capacity (0.53 meq/g) in comparison to the basis value used for this experiment. Material C: charred fermentation residue which was produced by the University showed the most efficient capacity of (1.69 meq/g). This in comparison with the value used as the basis for this experiment showed that material C (charred fermentation residue) is very efficient for zinc sorption. pH values measured at the effluent of all the experiment were slightly higher than the pH measured in the initiating water.

Feb 1, 2024

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By G. S. Austin

Soil next to an abandoned smelter near Socorro, New Mexico, has the highest Pb concentration in the clay-size fraction, although this fraction accounted for only 1 to 3 wt. % of the soil. The depth of contamination was determined in areas relatively undisturbed since the smelter was abandoned about 98 years ago. Lead concentration drops to background levels below a depth of 3 inches. A mineralogical examination of the fine-size fraction of Pb-contaminated soils revealed an absence of crystalline Pb compounds. We conclude that Pb is present either as amorphous phases or adsorbed on the surfaces of soil particles. Yet, because of the alkalinity of the soil, the movement of Pb-bearing particles controls Pb mobility, not chemical transport in solution. Plant material from the site contained elevated Pb levels that increased as the amount of Pb in the soil increased. Of the types of material tested, rabbit bush showed the greatest increase of Pb levels. Lead levels were highest in rabbit bush roots, whereas levels in creosote were highest in foliage. Levels in cactus varied. The amount of Pb due to dust incorporated in plant tissue is almost negligible compared to the amount absorbed through the plant vascular system.

Jan 1, 1992

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By Neil Williams

The brecciated dolostone-hosted (Mississippi Valley-type) and associated shale-hosted stratiform Pb-Zn deposits at McArthur River occur adjacent to a major syndepositional fault, the Emu fault. Base-metal zoning, mineral parageneses, and Pb and stable isotope ratios indicate that both types of deposits formed contemporaneously from metalliferous brines that flowed into the host sediments from the Emu fault. Derivation of brines from underlying evaporitic sediments is suggested. Geochemical evidence indicates that the mechanism of ore formation was sulfate-reduction coupled with oxidation of organic matter. The textural relationships of stratiform sulfide mineralization to diagenetic dolomite concretions, chert blebs, volcanic glass shards, and inter-ore breccia beds, indicate that the reactions proceeded diagenetically within about 100 m of the sediment/water interface.

Jan 1, 1979

By L. S. Hansen

Organized efforts toward the prevention of injuries and occupational diseases have been of comparatively recent origin in the mining industry, dating generally from the beginning of this century. Mining-and particularly underground mining- is more hazardous in many respects than most other major industries, and continual and increasing attention has been given to its health and safety aspects. The importance of the physical well-being of those engaged in mining was recognized by Agricola, who, after describing the hazards encountered in 16th century mining operations, stated that "Some of these evils, as well as certain other things, are the reason why pits are occasionally abandoned." In the past 50 yr particularly, mine managements and labor organizations, separately or collectively, have mounted productive efforts toward the prevention of accidents and industry-associated diseases and illnesses. A statistical study of this period indicates that increasing awareness coupled with the endeavors of all concerned agencies has resulted in decreasing frequency of occurrences of injuries and illnesses. In recent years particularly the mining industry has used the services of safety engineers, industrial hygienists, inspectors, ventilation engineers and other specializing in locating and correcting deficiencies affecting the welfare of employees. Concurrently, the labor movement has incorporated into its organization individuals working in the fields of health and safety, many devoting full time to these responsibilities. Others serve in behalf of their fellow workmen as on-the-job safety representatives. Most authorities agree that accidents are caused by (1) unsafe acts, (2) unsafe conditions and, exceptionally, (3) Acts of God. The "unsafe act" often is cited as the prime cause. but many accidents, and attendant injuries, are the result of a blend of "unsafe acts" and "unsafe conditions," with each chargeable in varying proportions. It therefore is necessary to consider both the physical elements of the mine plant and the training, mental attributes and actions of all personnel involved. Analysis of an accident, if based on hasty reconnaissance and unduly hurried questioning, seldom will disclose more than surface causes and consequently will result in inadequate measures to prevent repetition. Mining involves unavoidable and calculated risks, as in all facets of life. It is most important then that men employed in mining be schooled in the hazards and develop fully the ability to evaluate and minimize risks. The environment, of underground mining often is harsh and strange compared to the more natural surface conditions man has learned to cope with as a part of established life patterns. The miner. therefore, must adapt to unusual situations and conditions and must develop a mental attitude permitting acceptance of change. 3.1-INDUSTRY-AFFILIATED SAFETY AGENCIES L. S. HANSEN There are many organizations primarily interested in health and safety. In addition to industry and labor groups, there are many private and governmental

Jan 1, 1973