Search Documents

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By A. B. Cecala

Enclosed cabs have been used on surface mining equipment for many years to protect equipment operators from health and safety hazards. The surface mining and quarrying process is a highly mechanized process that generates large quantities of respirable dust. Due to economic factors, more older mining equipment is being used today than in years past. With this older equipment, it is common to observe deterioration of many components on the enclosed cabs which greatly reduce their protection effectiveness. NIOSH has performed a number of different field studies, as well as a comprehensive laboratory study evaluating various factors and parameters regarding enclosed cabs. NIOSH has recently completed a cooperative research effort with Sy-Klone International and Vulcan Materials Company to evaluate the effectiveness of a newly designed uni-directional filtration and pressurization system that brings all the clean filtered air in at the roof of the cab and extracts all recirculated air near the floor. This design provides the highest air quality to the equipment operator. Testing on this new system showed an almost 10-fold reduction in respirable dust inside the enclosed cab. The uni-directional design is easy to incorporate and should be considered for all new and retrofit systems in surface mining equipment.

Jan 1, 2009

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By D. W. Scott, D. G. Minnes

Introduction Ontario's diverse industrial mineral resource base includes structural minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone, and dolostone. These resources are used to produce aggregates, brick, metallurgical stone, fillers, cement, lime, and other construction materials. The majority of the operations are in deposits of Palezoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were more than 140 Mt (154 million st) of aggregates produced in 1985. About 115 Mt (128 million st) of that was produced in southern Ontario with the rest being largely from Crown land in northern Ontario. Structural industrial minerals account for more than 80% of the value of total industrial mineral production. The remaining 20% is accounted for by the nonstructural minerals, such as salt, which is produced in the southwestern part of the province. A host of other nonstructural industrial minerals are known. Production, though, is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite, and byproduct metallurgical sulfur products (Fig. 1). Major production is close to the large markets of urbanized southern Ontario and the northeastern and northcentral US. With an abundant variety of industrial mineral resources and the large population within 650 km (400 miles) of most deposits, the market offers great potential. Ontario's nine million people accounted for about 35% of Canada's entire $476.3 billion gross domestic product in 1985. This equates to about one-third of the nation's buying power being within a 200-km (125-mile) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well-developed industrial minerals industry that fulfills most of the structural industrial minerals demand in Ontario. Nonstructural industrial minerals are similarly well placed to compete in this high demand area. Although Ontario manufacturers still import some of these materials, Ontario products are achieving significant market share. And, they serve the needs of neighboring provinces and states. Present production and trends Ontario has traditionally produced significant amounts of industrial minerals. This produc¬tion had a value of $956 million in 1984 (Table 1). Structural materials production in 1985 and 1986 approached or exceeded levels not seen since the early 1970s. Many new products have been developed using these raw materials. The industry is becoming concentrated in the hands of several large companies, mainly four large cement com-

Jan 12, 1987

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By Günther M. Volkmann

Continuous developments in tunneling require knowledge transfer between designers and suppliers to optimize the application of support systems. This collaboration allows the designer access to the latest research results, technical innovations, and support specific measurement techniques as well as the supplier?s experiences on recent projects. Project specific requirements determine the information that can be used to increase support system efficiency, advance rate, degree of safety, or decrease costs. This cooperative effort results in not only an unambiguous tender document, but also an optimized design with reduced risk that is coordinated with safe and high performance construction techniques. This paper will address the benefits of an early collaboration to both the design and the specifications in the tender document by using the A3 Hindhead project (UK) as an example.

Jan 1, 2008

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

By Byron T. Darnton

Gravity concentration at the Pegasus Gold/Montana Tunnels Mine, near Helena, MT, began in June 1991 when a coarse-gold-scalping circuit was commissioned. It processes a small portion of the ball-mill circulating load to reduce the risk of gold particles that are too coarse to float from advancing to flotation. The circuit also cost-effectively enhances overall gold recovery and payable gold ounces. This gravity circuit has been a major success. Since the circuit was commissioned, throughput has increased 30%. Several modifications and improvements were made during the last three years that allowed the gravity circuit to keep pace with the higher tonnage. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project. It will allow for an estimated 50% increase in gravity gold production, while significantly reducing the unit costs of production.

Jan 1, 1995

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure'acid leaching.

Jan 1, 2002

By Donald W. Stever

In 1995 I was asked to participate in a litigation matter between a corporation and its insurance carriers concerning insurance coverage for remedial costs at a large, environmentally contaminated closed-down former industrial facility. One of the buildings on this site became known to the lawyers representing the company as “the infamous Building 8”. This building housed millions of documents retrieved from various locations at the facility while it was being shut down. It became apparent that the facility management had no document destruction policy, and thus Building 8 contained internal memoranda, notes, copies of correspondence, permits, operating records, inventory records, and the like from fifty years of operation. Needless to say, some of these documents, all of which were subject to discovery by the insurance companies in the litigation, contained material that was less than helpful to the company’s case. Of course, there were also a few helpful documents, but the overall usefulness of these records was outweighed by the negative impact they had on the conduct of the litigation. A second example involves e-mail. Several years ago, acting on an anonymous complaint that we later discovered was made by a disgruntled former employee who had been fired, a small army of federal environmental investigators descended on a client’s operating facility and, armed with a search warrant, literally commandeered the facility’s EH&S department. The investigators impounded the computers of the EH&S personnel and extracted all of the data from the hard drives of those PCs, as well as all EH&S related files from the hard drives of several servers used by the facility. These computers contained many years’ worth of stored e-mails, draft letters and memoranda, and other documents that provided grist for a four and one-half year criminal grand jury investigation of the facility and its EH&S staff. Both of these companies would have benefited from following a rigorous, enforceable, corporate records policy. Here is a third problem. My client had, during the 1960s, made a brief, and unprofitable foray into the nuclear fuel processing business. It ultimately sold the subsidiary, and was forced to give the purchasing company a broad indemnity against future liability. As might be expected, years later the facility was found to have considerable soil and ground water contamination both by chlorinated solvents and low-level radioactive material. Several years into the remediation program, my client discovered a tractor-trailer load of files, apparently removed from the subject facility, sitting in a parked trailer in a company-owned lot 300 miles away from the facility, where they had been for nearly thirty years. These documents were not helpful to the client, but had to be reviewed, at considerable cost, by paralegals. Moreover, several of the boxes turned out to have been mildly radioactive, setting off a chain of health and safety issues that consumed tens of thousands of dollars of legal expenses before they were resolved. Today, formal, enforceable corporate records management programs have become an extremely important element of overall corporate management. What was for most of the last century little more than a low level warehousing function is now a critical, actively managed, operating function that affects every level of corporate management. The rapid assimilation into corporate culture of electronic document management and the prevalence of e-email as the primary means of internal communication have created records management complexities the likes of which were not even conceived of fifteen years ago. Record preservation and destruction are no longer matters that can be handled on an ad-hoc decision making basis. Because of regulatory requirements affecting various classes of documents and the litigation consequences of ad hoc retention and destruction of corporate business records, and the need to have the ability to quickly retrieve documents in either a litigation or business negotiation context, a set of records management norms have evolved over time that have become the core elements of virtually every corporate records program. However, notwithstanding the existence of a set of norms (which are the basic elements of a

Jan 1, 2005