Search Documents

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By H. J. Handewith

This paper explores the state-of-the-art of mechanical rock drilling and boring methods in use in the year 2000. It covers the basic mechanisms of cutting tool design and outlines the current understanding of related rock fracture methods. It provides suggestions for future research needs and discusses the mining and construction markets that are driving these needs.

Jan 1, 2001

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By Daniel H. Isreal

Because the federal government owns and controls nearly 80% of the most valuable oil shale reserves in the West, it is inevitable that federal leasing and siting will play a prominent role in development of an oil shale industry during the 1980s. Also, because of recent enactment of the Synthetic Fuels Corp. authorizing up to $88 billion in loan and price guarantees-federal financing will provide the critical incentive to permit private investment in a still infant industry.

Jan 1, 1981

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By K. Sasaki

Diffusion phenomena in mine airways are important to trace gas and dust introduced into mine ventilation flows. Authors have carried out tracer gas measurements to check mine ventilation using concentration-time curves measured in mine airways, however dispersion mechanism to enhance effective diffusion have not been cleared. A numerical model using discrete tracer points dosed into tube flow has been presented to simulate their movements in consideration of turbulent velocity profile and fluctuation. Numerical simulations have been carried out to predict distributions of dosed points in tube flows with turbulent velocity profile, turbulent intensity profile and Reynolds stress. The numerical simulation results show that a combination of turbulent velocity profile and fluctuation creates extremely large dispersion of points in longitudinal direction and concentration curve with long tail was observed. This dispersion by velocity profile and fluctuation contributes large effective diffusion coefficient compared with original diffusion coefficient dominating in uniform velocity fields. Furthermore, the effect of Reynolds stress on the concentration-time curves is discussed.

Jan 1, 2009

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By Marcelo de Oliveira, Antoine Allanore, Dennis P. Chen, Davide Ciceri

Potassium fertilizers (potash) are mined in a handful of countries in the Northern Hemisphere. Potash is either expensive or unavailable to the farmers of the Southern Hemisphere. Alkaline alteration of K-feldspar rock (ultrapotassic syenite) in autoclave in the presence of Ca2+ generates a mixture of K-bearing calcium-aluminum-silicate-hydrate (C-A-S-H) minerals that potentially can be used as an alternative local fertilizer. This work investigates the effect of processing temperature (200 °C, 220 °C, and 230 °C) and time (from 0.5 to 3.0 h) on pH, mineralogy, and elemental availability of the C-A-S-H mineral mixture. Increasing temperature results in an increased conversion of K-feldspar and increased content of both the mineral tobermorite (Ca5Si6O16(OH)2·4H2O) and amorphous phase in the resulting C-A-S-H mixture; increasing time results in an increased conversion of α-dicalcium silicate hydrate into tobermorite. The amount of K leached from the mixture is relatively constant across all processing conditions. Hydrothermal alteration in autoclave of K-feldspar-bearing rocks such as ultrapotassic syenite permits the synthesis of a potential potassium fertilizer which alkalinity and mineralogy can be tailored according to soil requirements.

May 22, 2020

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By John Mitchell, Mark K. Jorgensen

Newmont Mining’s Ahafo Mine is located in Ghana approximately 300 km (190 miles) northwest of the capital city of Accra in the Brong-Ahafo region. The nearest city is Sunyani, located 45 km (28 miles) to the north. The Ahafo Mine will process ore from seven major pits that extend along a 40-km (25-mile) strike. Four pits are in the south and three pits are in the north. The resource is currently stated at 373 t (12 million oz). But it still has the potential for growth both from new discoveries and the development of underground operations.

Jan 1, 2007

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By W. E. Roscoe, K. N. Spence

In the Canadian mining industry, there are at present no comprehensive regulations or standards for valuation of mineral properties. In January 1999, the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. The authors were subsequently appointed Co-chairs of the CIM Special Committee on Valuation of Mineral Properties (CIMVal). A committee of experts from the mining industry, consulting, financial and legal communities was established with the task of reviewing available information, investigating various valuation methodologies and practices, soliciting input from interested parties, and recommending a Canadian code or standards plus guidelines for the valuation of mineral properties. As an initial stage of its work, the CIMVal Committee organized a one day session at the Mining Millennium 2000 Convention in Toronto in March 2000 on valuation of mineral properties. The 10 invited papers have been published by CIM. As a second stage, CIMVal has requested input and comments from all interested parties. The next stage will be to prepare a preliminary draft with a recommended code or standards and guidelines. This will be circulated for further input and comments prior to revision and publication of another draft. The final CIMVal report should be completed in early 2001. A variety of methods are in common usage for the valuation of mineral properties, depending on the stage of development of the property, the data available and the experience of the valuator. For example, the discounted cash flow method is commonly used for properties in production or at the feasibility stage, but is not generally considered appropriate for exploration properties. Market approaches such as comparable transactions are in wide general use, and various cost approaches are used for exploration properties. The option pricing approach has promise for valuation of marginal properties, but is not commonly used.

Jan 1, 2001

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By J. Kretschmann, N. Nguyen

"The Vietnamese economic growth of more than 5% per year leads this country to an enormous demand for raw materials. In the duration of ongoing expansion, the big challenge in the coming decades will be to make this process as sustainable as possible when it comes to economic, environmental and social objectives. Risk management especially in occupational safety and health (OSH) in enterprises is one of the most important tools to achieve this aim. But until now, this has not been taken into priority by Vietnamese coal mining enterprises. Main reasons for this situation can be found in deficient legislative conditions and in non-synchronized risk management systems. In contrast, Germany has implemented an adequate legal system and the German mining industry has gained lots of experiences in risk management, especially in occupational safety and health. This paper seeks to point out specific challenges how to improve occupational safety and health in Vietnam by transferring and applying German methods and standards."

Jan 1, 2011

By Felicity Lloyd, Stuart Kearns, Roger McLimans

The metamorphic terrane of southwestern India is a geological environment containing ilmenite source-rocks, transport drainage systems, and resultant beach sand deposits that contain altered ilmenites greater than 60wt% TiO2. As such, this environment provides a geological laboratory, from source to deposit, for the investigation of ilmenite origin, alteration, and geochemical character. Ilmenite samples from potential source rocks, river sands, and beach sands all show degrees of alteration and a variety of alteration textures (iron leaching) producing leucoxene (here defined as >70 <90wt% TiO2) and progressing to rutile (here defined as >90wt% TiO2). Distinct alteration textures are specific to different source rocks and are used together with trace element geochemistry as provenance criteria. Ilmenites are classified on the basis of their trace element content. In India, the ilmenites are classified principally according to the Mg, Nb, and Mn content and this signature defines potential source rocks, even where the ilmenite is altered to a TiO2 content of 70wt%. The trace element data may fingerprint source rocks whose ilmenite is more prone to iron leaching and that criterion has application in exploration for higher-grade ilmenites.

Jan 1, 2005

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013