Search Documents

By Phil Morriss

During the last 12 months, Sandvik?s Technical Service Group has carried out nine Scoping and Pre-feasibility studies for the application of In-pit crushing and conveying (IPCC) for large mining companies; the majority in conjunction with the Snowden Consulting Group. During these studies several key and recurring drivers have been identified: 1. Mining schedule issues ? there are several issues which crop up repeatedly, including: ?the unnecessary curvature of pit walls, ?very high rates of vertical advance which are (created by schedule optimisers to minimise stripping at all times) which are at the limit of what can be realistically achieved (and which of course make it harder for IPCC to achieve any impact), and ?The allocation of material to semi-mobile systems to maximise the ability for IPCC to be an effective alternative. 2. IPCC productivity issues ? the key issues are the IPCC system operating hours achievable, and the system throughput (both instantaneous and the average). 3. IPCC Risk issues ? there are perceptions about the risks associated with the use of IPCC which are a mix of reality and fiction, but which nonetheless create negativity towards the use of IPCC. In this paper, the authors wish to address specifically the factors affecting the IPCC productivity.

Jan 1, 2008

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By Isobel Clark

This paper reviews some of the traditional methods of reserves estimation based on lognormal distribution with or without an additive constant. In the rush to computerize mine planning and grade control generaly, proven estimation methods, such as Sichel's t, seem to have been overlooked. By use of a personal microcomputer, the traditional methods were investigated thoroughly, the results being tested against existing tables and figures. The fitting of a lognormal distribution, including estimation of the additive constant, is discussed, and the calculation of Sichel's t estimator and its associated confidence limits is described in detail. Payability calculations for a lognormal distribution are also covered briefly. The advantages of personal computers, particularly speed and ease of use, are emphasized. This low-cost approach permits detailed investigation of some of the assumptions and approximations inherent in the established methods of calculation. Several disturbing discrepancies are revealed in various factors, and some generalized statements made by previous authors are found to be over-simplistic. Full details are given of acceptable approximations and computer algorithms, and concern is expressed over the possible loss of proven methods under the welter of new, sophisticated computer software.

Jan 1, 1987

NIM Reports Report No. 1563 Neutron activation analysis of samples from the Kimberley Reef Conglomerate. Report No. 1569 The use of DDTU as an analytical reagent for the noble metals. Special general meeting A Special General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 14th November, 1973. The President, Mr P. W. J. van Rensburg, opened the meeting at 9 a.m. and read the notice of the meeting, which was as follows: Colloquium and general meeting CONSTRUCTION OF SLIMES DAMS A General Meeting and Colloiquum on the above topic was held on November 14th and 15th, 1973, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 135 delegates and was opened by the President at 9.10 a.m. Orange Free State Branch PROCEEDINGS OF THE ANNUAL GENERAL MEETING The Annual General Meeting of the Branch was held in the Western Holdings Cant,een on Tuesday, 11th September, 1973, at 7.00 p.m. Book Review Westwood, W., and Cooper, B. S. Analytical methods in use in non-ferrous minin~ and metallur~ y: a selective review. London, Institute of Mining and Metallurgy, July 1973. 54 pp. £3.50.

Jan 12, 1973

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

1. Book review . Australasian coal mining practice, edited by C.H. Martin. Reviewer: R.B. MacGilIivray This book is an extremely comprehensive coverage of coal-mining practice in Australasia, the countries covered being Australia, New Zealand,and Papua New Guinea. 2. From The Institute of Metals The folowing are available from The Institute of Metals, 1 Carlton House Terace, London SWl Y 5DB. Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00. High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15. New cored-wire injection techniques, particularly as Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45. Marine engineering with copper-nickel. 1988. 103 pp. £18. Characterisation of High Temperature Materials. 3. New journal FMJ International Publications Lid have announced a new quarterly publication, Aluminium Today. 4. Other new publications Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95. Proceedings, Foundry and Heat Treatment 88. R150 per set of 5 volumes, or R40 per volume.

Jan 1, 1989

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

The case for national research in mineral processing PRESIDENTIAL ADDRESS given by R. E. Robinson*, Ph.D., B.Sc. (Eng.) (Wits.) Some of you have only raised your eyebrows, some have made tactful comments, and a few of you have been fairly outspoken, but all of you in industry are concerned at the high level of State expenditure by bodies such as the National Institute for Metallurgy. The case for a national research organization in mineral processing is not clear-cut and in fairness I must present both cases - for and against. Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute.

Jan 10, 1975

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, there by lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3Dmulti-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2006

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By E. Lutz, M. Momayez, K. W. Brown Requist

As real-time air quality monitoring becomes more prevalent in US underground mines, it is important to provide the highest data reliability with the fewest possible sensors. Real-time sensors remain costly, and these costs are not exclusively financial; the time required to install, calibrate, and maintain real-time sensors poses a large barrier to widespread implementation. Current atmospheric monitoring systems typically rely on displaying point-specific values. This requires operators to infer real-time airborne contamination distributions. Monitoring and control software utilizing mine ventilation network (MVN) solvers has been implemented in limited cases because of their ability to simulate ventilation systems quickly, but these solvers use a one-dimensional representation of the mine, limiting spatial resolution of estimated distributions. Computational fluid dynamics (CFD) has likewise been considered as a means to improve spatial resolution, but processing times prevent its use as a basis for monitoring and control. For the real-time monitoring of airborne contamination distributions, we propose a spatial interpolation method that can estimate the distribution of airborne contaminants in near-real time. This method provides a middle ground between fast processing times and increased spatial resolution. With the use of a pathfinding algorithm and optimization through absolute percentage error minimization, this method outperforms spatial interpolation with a Euclidean distance. By providing contamination distribution information to operators, this method and its derivatives stand to outperform current atmospheric monitoring systems.

Apr 16, 2024

By E. Isokangas

A mine is essentially a series of operations, including drilling and blasting, crushing, milling, flotation, and leaching, that are interconnected and therefore interrelated, with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often causes potential economic benefits and energy savings to be missed. However, the PIO methodology is a thorough approach which considers these individual process activities within the context of the whole process. The basic principle is to optimize the process as a whole, rather than each process step in isolation from the others. Metso?s Process Technology and Innovation (PTI) group offers a global consulting service for the mining and construction industries. A significant amount of this consulting work involves process integration and optimization (PIO) studies. When conducting a PIO study, every aspect of the process is considered. In addition to drilling and blasting, transportation, handling and storage, crushing, screening, grinding, flotation, separation, and recovery, other aspects including equipment utilization and energy consumption and even greenhouse gas emissions are also included if necessary. In a PIO project, it is very important to understand what type of material is being processed at any point in time. That is, which domain or domains is the material part of? This is necessary in order to observe the effect of different ore sources (and the blending of sources) on concentrator performance. Linking the ore from the pit to the concentrator required the development of an ore tracking system. As a result, PTI developed a radio-frequency based material tracking system called SmartTag?. This system allows tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles, and finally into the concentrator. Using the SmartTag? system, definitive correlations can be made between the performance of the plant and the plant feed characteristics, including the domain from which the feed ore originated. Since its commercialization in 2007, SmartTag? has been used in the majority of PTI?s consulting projects and several permanent systems have been installed worldwide1. Successful applications of the SmartTag? system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This paper describes how the SmartTag? system is being utilized by PTI and the benefits being gained by its use in PIO projects, as well as presenting some case studies.

Jan 1, 2012

By J. O. Roux

The Impala Platinum Limited Base Metals Refinery in Springs, South Africa, refines convertor matte containing base metals and PGM?s (platinum group metals) using a hydrometallurgical process. In addition to a PGM-rich concentrate that is further refined, the Base Metals Refinery produces nickel (in powder or briquette form), copper cathodes and cobalt powder. Five leaching stages are utilized to remove the base metals and impurities from the PGM concentrate. The project described in this paper involves a radical redesign of the second stage leach autoclave with the aim of reducing maintenance costs and downtime, increasing throughput and ensuring a safer working environment. The second stage leach process at the Base Metals Refinery, produces a PGM-rich residue through the extraction of copper and any remaining base metals from the first stage leach solid residue material. Leaching is performed in an autoclave operating at a pressure of 600 kPaG and a temperature of 140°C to 150°C. Concentrated H2SO4 is added to the feed to produce a solution with a free acid content between 10 and 30 g/L and a pH of less than 2. Oxygen is passed into the 1st and 2nd compartments of the autoclave. As a result of the aggressive, highly oxidizing conditions within the autoclave, the original design utilized a heavy wall carbon steel shell with lead lining and two layers of acid bricks. The bricks acted as a wear resistant material and ensured a low surface temperature at the skin of the lead lining, whereas the lead lining acted as a corrosion barrier to protect the steel shell. These brick lined autoclaves were heavy, maintenance intensive and prone to catastrophic failure. A radical autoclave redesign was needed to reduce the high costs of manufacturing, installation and operation. Finite element modelling was used to optimize the design and various high alloy materials were investigated for the application. Based on extensive test work, the carbon steel shell was replaced with duplex SAF 2205 stainless steel in the new design. The use of this highly corrosion resistant material, eliminates the need for the lead and brick linings and reduces the wall thickness requirements substantially, resulting in an increase in the available volume for the same external shell dimensions. The vessel is welded in circular sections to form an elongated, impermeable, cylindrical body, with several agitator nozzles and compartments. The first new duplex stainless steel unit has been in continuous operation for more than 24 months and its performance has exceeded the highest expectations. The design was so successful that a patent has been registered. The major benefits of the new stainless steel design include increased throughput, improved performance, less downtime and a safer working environment. Lead has been eliminated and replaced with a more environmentally safe material, and the total lifespan of the vessel has been extended. In addition, the autoclave project has made significant developments in advancing the field of welding and optimizing the integrity of welding quality standards in South Africa.

Jan 1, 2009

By L. R. Nelson

The efficiency and cost-effectiveness of the aluminothermic reduction process in the production of ferro-alloys and 'pure' metals depends strongly on appropriate balancing of the process energy required. Insufficient energy results in a poor metal yield, while over-supply can result in excessive fuming and possibly even ejection of the reactor contents in a potentially dangerous 'thermite bomb' reaction. This situation becomes even more critical when the suitability of limited quantities of oxide from new sources must be evaluated, dictating smaller-scale testwork. The resulting higher relative heat losses from the system complicates control of the energy balance, and usually requires the addition of thermal boosters or reactant preheating in order to sustain an autothermic process. This often detracts from the quality of the metal product, and adds to the hazards of batch aluminothermic- reduction testing. The development of a small-scale method (producing less than 2,5 kg of metal) for the plasma-assisted aluminothermic reduction of chromium oxide that overcomes such difficulties is described. The technique involves the use of a sealed 50 kVA plasma-arc furnace to provide controlled electrical ignition and supplementary energy to the reactants contained in a water-cooled copper crucible. The application of the method to the evaluation of the aluminothermic production of pure chromium metal from a unique chromic oxide source is reported.

Jan 1, 1996

By M. J. Latva-Kokko, CA Snyders, J. R. Peltola, M. K. Kostiainen

It is well known that carbon management is essential for minimising soluble gold losses in carbonin- leach (CIL) and carbon-in-pulp (CIP) circuits. Even so, carbon measurements remain predominantly a manual operation with a low amount of control and automation around CIL and CIP reactors. Carbon inventory, i.e. knowing the carbon concentration in each reactor, is crucial for good carbon management. CarbonSense, a novel in-situ measurement system, was therefore developed for continuous monitoring of the carbon concentration in each reactor and paves the way for more advanced control in gold operations. The carbon management and optimisation system is based on Outotec® HSC Sim dynamic process simulations where each process component is modelled in detail. Generated models are validated with real data from a particular operation. The simulator will allow for the carbon control sequence to be realistically tested and the efficiency optimised by controlling the feed and discharge pumps in a hazard- and risk-free process environment. Furthermore, by combining CarbonSense and Outotec® gold courier (online soluble gold measurements) continuous feed-forward and feedback information can be obtained. The optimiser will then define the best running parameters based on the cost function of gold production versus intrinsic factors such as utility costs and adsorption time. Eventually, the application can be installed parallel with a real process island and it can be continuously calibrated with real-time process data. The dynamic model will then create future predictions for the entire process island. The example case presents a CIL circuit, which is simulated using Outotec® HSC Chemistry Sim and operated through Outotec® ACT (Advanced Control Tool) application. Keywords: Carbon-in-leach, CIL, CarbonSense, carbon management, automated control, simulation

Jan 1, 2020

By G. H. Morton

The tenth international symposium on the application of computer methods in the mineral industry (APCOM) was held in Johannesburg in April; the first time it had taken place outside North America. In the technical sessions fifty-seven papers were presented, providing a review of current work and including some important original contributions. These papers and a full account of the discussion at the symposium will soon be published in a single volume. The Technical Programme The first session of the symposium included an opening address given by Mr J. W. Shilling, President of the Chamber of Mines of South Africa, and a keynote address by Mr K. F. Lane of the Rio Tinto Corporation Limited. Mr Shilling spoke about the history of the South African mining industry and about some of the work of the Chamber of Mines. He stressed the importance of the symposium in familiarising those in mining with computer applications, and expressed his hope that it would stimulate and inspire scientists and engineers in the effort to develop safer and more economic methods of mining. Mr Lane, talking about economic and financial modelling, gave a fascinating account of the experience of RTZ over the last twelve years. In a very honest appraisal of the substantial progress that had been made, he confessed some disappointment not only in the cost and

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019