Search Documents

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Steven J. Schatzel

Large-scale methane releases in dual salt mines have resulted in ignitions and mine fatalities as recently as 1979. Several past studies have implied that hazardous methane occurrences in U.S. salt domes are distributed neither uniformly nor randomly, but are geologically controlled and potentially predictable. A first step by the Bureau of Mines in addressing the problem of methane in deal salt mines required development of a new test to determine volumes of gases in solid salt samples. This report considers the results achieved when 80 deal salt samples were tested for gas content by dissolution in a controlled atmosphere chamber. Criteria were organized to delineate salt types based on geological occurrence. Outburst samples range from 0.014 to 7.4 cm3 CH4/100 g NaCl, anomalous salt samples from 0.0027 to 2.6 cm3 CH4/100 g NaCl, and normal salts from less than 0.0003 to 0.31 cm3 CH4/100 g NaCl. The presence of higher hydrocarbons was most common in samples containing larger quan¬tities of methane. The presence of higher hydrocarbons appears to be useful in detecting methane hazards where some methane may be lost before gas content testing. An exploratory rotary and/or core drilling program, dissolution testing for gas content, and up-to-date geologic mine napping could allow a mine operator to assess methane hazards in dual salt.

Jan 1, 1984

By Wilbur I. Duvall, S. L. Windes, Leonard Obert

"Previous investigations, too numerous to be listed in entirety, have been performed to determine the physical properties of rock. When considered according to their objectives, most of these investigations can be grouped as follows: First, the geologic group (1,2),4/ in which the purpose was to obtain information on the physical properties of the rocks that make up the earth's crust. Particular emphasis has been placed on the determination of the elastic constants--that is, Young's modulus, the modules of rigidity, and Poisson's ratio – as these quantities determine the propagation characteristics of seismic waves. Second, the structural properties group (3 - 11), in which the physical properties of architectural or monumental stone, concrete and aggregate rock, road blocks (cobblestone), and the like were desired. The tests have been quite general and include, besides the elastic properties; the compressive and tensile strength, and the toughness, hardness, and weathering properties of many types of rocks.To .a lesser degree, investigations have been carried out to determine the physical properties of mine rock. A few reports (12 - 14) present data on the crushability and grindability of mine rock, and a large number of papers discuss grinding and crushing procedures and methods of analyzing the data (for example, see references 15 - 17). Some of the latter group also have given the results of tests on mine rock; however, comparatively few include an adequate petrographic description or information on other physical properties of the rock. A few papers,(18 - 22) have reported studies of the strength of rock specimens in respect to the strength of parts of mine structures, such as pillars, roof, arches, etc. Other papers (23 - 26) have discussed investigations on such subjects as primary and secondary crushing, diamond and pneumatic rock drilling, explosive breaking and shattering of rock, rate of drifting and miring, and other allied problems. The majority of these reports have given no more than a cursory, description of the rocks and have included no statement regarding the physical properties. When statements have been given regarding the physical properties, they have usually referred only to isolated tests, making correlations between variations in the physical properties and variations in the .test under consideration difficult, if not impossible. Some reports have included handbook values on such characteristics as the crushing strength, hardness, and toughness. This practice is not satisfactory, because these values are usually given for col¬lective types of rocks, such as granites, limestones, and marbles, and it is known that the variations of the physical properties within these groups is often larger than the differences between the groups."

Aug 1, 1946

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

By J. D. Brown

The electron optics, vacuum system, and sample stage assembly for the Bureau of Mines? electron probe X-ray spectrograph were purchased. Four scanning curved-crystal spectrometers, two reflection- and two transmission-type, were designed and constructed by the authors. The reflection spectrometers are placed in a vacuum chamber for measurement of long-wave-length X-radiation. Detection, pulse-amplitude discrimination, and recording circuits are provided for the simultaneous measurement of four X-ray spectral lines. Minimum spot size is approximately 2 microns in diameter at 30 kilovolts and a sample-to-ground current of 5 x 10-8 ampere. At this voltage and current the limit of detection with reflection spectrometers is less than 0.05 weight-percent for most elements. The limit of detection for elements determined by transmission-type spectrometers, evaluated at 35 kilovolts and 5 x 10-8 ampere, is approximately 0.1 weight--percent for all elements having excitation voltages below 20 kilovolts. In general, reflection spectrometers exhibited satisfactory but poorer resolution than the transmission type, resolution of the spectrometers being limited primarily by crystal imperfections, with greater mosaic structure being introduced by the grinding process for the reflection crystals. Several applications of the electron probe X-ray spectrograph are described. Analysis of a uranium-steel is discussed in detail to illustrate calculation of composition from measured X-ray intensities.

Jan 1, 1962

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967