Search Documents

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983

By James C. Fowler

As report covers the installation and testing of a permanent seismic monitor system at the Loveridge Mine in West Virginia. The testing of the system showed several things: 1. Getting the seismic data hack to the central computer in a usable form is possible 2. It is possible to detect small explosions. 3. The use of this system as a auxiliary system to detect hammer blows from miners trapped in the area of one of the geophones is possible.

Jan 1, 1974

By R. A. Meister

The study on improving surface coat refuse disposal site inspections included surface inspections of 15 refuse disposal sites. Monthly aerial photos were taken of the sites and computer methods were used to determine elevation changes. Photogrammetric techniques that were used are described in detail. A comparison of the results of each of these inspection techniques is included. A detailed evaluation of the photogrammetric techniques was made and conclusions were drawn concerning the advantages and disadvantages of using aerial photography and photogrammetry as part of the inspection procedure. Operators' opinions of the aerial photography methods are included.

Jan 1, 1980

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By R. S. Dean

[During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use. During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use.]

Jan 1, 1940

By Oliver C. Ralston

The minerals that enter welding-rod coatings and fluxes are the main subject of this report. Few mineral producers know just what minerals and what grades and quantities of minerals are required by the welding trade, and it is for their information that this report has been prepared. The various methods of welding are discussed extensively enough to inform this type of audience. Specialists in welding probably will find little on welding that is of value to them, but they may learn something more about the minerals or mineral products that they use. The authors did not find it easy to prepare this publication, and any needed corrections will be welcomed. Regarding welding, research, Jenks4/ 1 points out that while the process of welding in simple in operation, the phenomena attending its use are extremely complicated, and the efficient and safe use of welding requires an understanding thereof. Although the fluxes and the coatings used have solved many problems, many other problems require the joint effort of the whole industry; therefore, it is hoped that this report will be found of practical value.

Jan 1, 1940

By Rudolf E. Greuer

This report contains a theoretical study on the usefulness of fighting mine fires with inert gases. Four introductory chapters review the role of fires in the mining industry; the conventional fire fighting techniques, the influence of inert gases on the burning of gases and solids, and the well established inert gas fire extinguishing systems for buildings and machinery. A large chapter describes the use which inert gas has found so far for fighting mine fires in major mining countries. More applications have occurred than generally expected and the inert gas method has in the last years become routine in Czechoslovakia and the USSR. This chapter is based on an evaluation of the extensive literature as well as on personal information obtained from leading experts.

Jan 1, 2012

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Robert Stefanko

This report abstracts project work performed for the USBM Grant No. GO-133077 during the period 19 June 1973 to 15 October 1974. Five reports have been separately produced and are as follows: 1. Mine Electrical Systems Evaluation - Cable Splicing, 2. Mine Electrical Systems Evaluation - Explosion-Proofing of Mine Containers, 3. Mine Electrical Systems Evaluation - Transient Analysis, 4. Mine Electrical Systems Evaluation - Mine Power System Performance, and 5. Mine Electrical Systems Evaluation - Model Coal Mine Electrical System Specifications. Abstracts of each comprise the balance of this executive summary, and 50 copies of each volume have been forwarded to the USBM under the terms of the grant agreement.

Jan 1, 1974

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By Stan Henning

The monthly summary of the climatological record for the demonstration mine is presented in Table 1. Tear normal temperatures occurred throughout the growing season. From May to October precipitation was more than normal except in June when it was 2.55 inches below normal. Corn and soybean plantings were delayed until June 2-7 because of wet field conditions. This is about one month later than normal for corn planting. Insect infestations were much less than those encountered in previous years. Cutworm activity was not noticed and alfalfa weevil infestation were small and patchy. Stalk rot in corn was a significant problem at harvest and resulted in much Milk lodging. The wet and generally overcast conditions of July, August and September were bend 10 beneficial al to certain plant disease organisms. For example, pumpkins planted in a small garden area at the demonstration mine did not ripen because of a powdery mildew resulting from overcast, wet conditions. Field operations and row crop plantings were greatly delayed by wet field conditions. It was difficult to plant by conventional tillage because the soil remained soft and sticky where the moldboard plow had been used. Plots in the no-tillage system could he planted before conventionally tilled plots could be traversed. Plant emergence and plant density at

Jan 1, 1982

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

By R. S. Dean

[During the past fiscal year the Metallurgical Division has made important contributions along the lines dictated by the Bureau policy of conservation of domestic mineral resources through Its investigations include determining of fundamental data of metallurgically important materials improvement of standard ore-treatment method to eliminate waste and improve the grade or recovery of the products; and development o new metallurgical processes.]

Jan 1, 1940

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By A. C. Fieldner

This report, the third of a series of annual reports of research and technologic work on coal by the Technologic Branch to be released in this form, covers the fiscal year July 1, 1937, to June 30, 1938. Ever-increasing demands for information on the chemical and physical properties of coals, their proper classification rind adaptability for various uses, their economic evaluation in the complex relationships between the costs of production, distribution, and selling, and their beneficiation and amenability to conversion to more valuable and. new products of commerce have necessitated an appropriate and flexible program. To most these requirements, initiation of new projects and new physical facilities has been made.

Jan 1, 1939

By Charles Findlay

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By R. O. Pynnonen

This publication presents a study by the Federal Bureau of Mines of 494 accidents in open-pit iron-ore mines, beneficiation plants, and shops of the Lake Superior district from March 1949 to June 1956. These accidents caused 499 lost-time injuries, including 12 fatalities. A similar Bureau publication, Information Circular 7744, Analysis of 346 Accidents, Underground Iron-Ore Mines, Lake Superior District, was published in April 1956. Accident reports were analyzed by the Bureau to show the causes of in-juries and the unsafe practices or conditions that caused the accidents. Also shown are the time charges, times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 27 percent of the total number of disabling accidents that occurred in open-pit iron-ore mines, beneficiation plants, and shops in the district during the period covered. The text also contains tabulations of the accident experience and graphs with straight-line injury-frequency, injury-severity, and fatality trends for the period 1946-57.

Jan 1, 1959

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, The United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Norway, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992