Search Documents

By M E. Hanson, K Chong, R H. Jacobson, S C. Way

To create conditions for economic rates of mineral recovery in a deep, hard rock mass, enhancement of naturally occurring permeability is necessary, and may be achieved through explosives detonated in boreholes. Previous theories of explosively created permeability are reviewed and found to relate permeability solely to the degree of fracturing, neglecting porosity. A theory is presented that includes both fracture density and porosity, and its results are applied, together with a knowledge of explosive behavior, to derive design parameters for in-situ mining.

Jan 1, 1983

By Lon D. Santis

This paper describes a lightning warning system (LWS) in operation at the U.S. Bureau of Mines' (USBM) Pittsburgh Research Center (PRC) from December, 1989 to April, 1991. An electric field mill measured the DC atmospheric electrostatic field. Also, an economical on-line weather data service provided lightning location maps and other weather information. A system such as this can significantly improve the safety of explosive handling. The use of these two methods addresses the detection of thunderclouds building overhead and the prediction and tracking of developed storms. Warning reliability of the system was very good when data from both sources were considered. Experience showed, however, that use of either system alone would not provide adequate reliability in most situations. Some problems occurred with the field mill and there is some question whether the instrument is compatible with harsh mining environments or could be made portable. Another method ' of measuring electric field based on fiber optics is discussed. This technology may be able to overcome the problems with field mills.

Jan 1, 1993

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By Claude Cunningham

AEL’s Electronic Delay Detonators are in routine use and growing in both volume and breadth of application in Africa. This trend will continue and grow internationally owing to increasing pressure on rockbreaking operations to conform to sustainable development principles. A fundamental breakthrough has been achieved, bringing production blasting into line with technologies, which leverage performance through tight monitoring and control. When moving from pyrotechnic systems, benefits are normally realized without having to adopt different timing patterns, but significant additional benefits are realisable by using the flexibility and precision of the electronic units to enter windows of timing previously closed. The higher price and increased care needed are a worthwhile investment, enabling operations to cross the chasm to stronger revenues, but the system must be robust and suited to the application and personnel. Economic models are vital for keeping track of the potential and achieved benefits of these systems. Some resistance can be expected from those who stand to lose income as a result of the improved efficiencies.

Jan 1, 2004

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By John Floyd, Larry Wardrip

A series of tests were conducted to evaluate the performance of a high density, high velocity cartridged explosive. The tests included two production blasts in a limestone quarry and two production blasts in a granite quarry. To quantify blast and product performance, each blast was monitored with the following equipment: l Two (16mm (Lo Cam) high speed cameras (500 images per second) l Velocity of detonation recorder (I million samples per second) l Four face motion accelerometers (1 million samples per second) l Digital seismograph The fragmentation distribution produced by each blast was quantified with digital image analysis The benefits of the use of high velocity, high density toe loading was quantified in terms of: l Vibration reduction l Fragmentation improvement l Excavator performance In addition to the field tests, a comprehensive evaluation was performed to determine the cost/benefit relationship of the use of the toe load. This paper will include the findings of the study along with guidelines for use in other quarry operations.

Jan 1, 2002

By Steven V. Crum, Willard E. Pierce

Concern has been raised about the adequacy of current regulatory guidelines designed to protect homes from unwanted blast damage due to low frequency ground vibrations; in particular those with predominant frequencies below 6 Hz. This report summarizes and updates the preliminary results of a continuing Bureau of Mines investigation which will be completed later in 1995. Four structures at four different surface coal mines have been studied by examining their response to ground vibrations created from overburden blasting. House response to ground vibrations with dominant frequencies down to about 3 Hz were recorded. Many of the blasts produced ground vibrations with peak amplitudes above expected crack-producing thresholds. Response motions were compared to those predicted by theoretical single degree of-freedom response models.

Jan 1, 1995

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011

By Paul Worsey, Seokbin Lim

In many high explosive applications, the explosives are covered or clad by a metal. This metal cover may serve a variety of purposes including: 1) to protect and prevent the disturbing or misshaping of the explosive during its transportation, handling and use, 2) in many military applications the cover material itself is used to provide a required effect, for example, the shrapnel from grenades, the metallic liner of shaped charges, and the confinement of explosives so they perform optimally, and, 3) in civilian applications in the use of well perforating shaped charges and linear shaped charges used for the demolition of steel structures such as bridges. For these reasons the interactions between the explosives and their covering materials are of great importance in understanding the performance of these devices.

Jan 1, 2005

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999

By Richard A. Dick

On August 3, 1977 the 95th Congress passed Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. This Act created the Office of Surface Mining Reclamation and Enforcement (OSM), which was given the responsibility of formulating regulations to implement the Act. This paper explains the rationale behind the specific provisions of the final blasting regulations, which were published in volume 44, No. 50 of the Federal Register, dated March 13, 1979. The major items covered by the regulations include preblasting surveys, blasting schedules, protection of the public, ground vibration limits, the scaled distance equation, airblast limits, blasting procedures, and record keeping. The regulations are designed to protect the safety and well-being of the public and to protect buildings and structures such as wells, pipelines, and storage facilities from damage.

Jan 1, 1979

By Virgil J. Stachura, Calvin L. Cumerlato

The Bureau of Mines conducted a series of tests to develop a blasting method that would reduce overbreak and rockfall hazards at a limestone quarry in northeastern Wisconsin. Reductions in overbreak were achieved by shortening the main explosive column and reducing the explosive load in shortened stemming zones in shotholes which were to form the highwalls. Two blasthole diameters, 3 and 4 inches, were used with 7 by 7 foot and 9 by 12 foot burdens and spacings respectively. ANFO, Comsol 300, or PowerAN were used in the body of the shots and Gelmax or 40 pct extra dynamite cartridges were used in the reduced load zones. Smoother highwalls were visually apparent, however further analysis by seismic refraction techniques were performed as an aid to studying overbreak within the rock mass.

Jan 1, 1989

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023