Search Documents

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By R. J. R. Schaller

NO. 3 winze, the sixth shaft to be sunk on the San Antonio property, is practically a duplicate of No. 3 shaft, which was the main shaft prior to the installation of the larger hoisting equipment in 1939. It is collared on the tenth, or 1,500-ft., level, and goes down vertically to the sixteenth, or 2,500-ft., level, with a loading pocket, spill pocket, and sump below this. It is 1,000 feet east of No. 3 shaft. All ore, men, and materials are handled through the latter. The winze location with reference to the rock formation is shown in Figure 1. (In plan, this section strikes N.30°E. and cuts most of the main orebodies of the mine normal to their strike.) It is collared eighty feet inside the footwall contact of the basalt and cuts through it before reaching the eleventh level. In this location there will be no ore tied up in shaft pillars, as the closest ore to the shaft is on the tenth level, and here it is eighty feet northeast of the collar. The winze headframe and hoist-room straddle the main haulage to the No. 3 shaft, on the tenth level (see Figure 2). At no time during the excavation for the headframe and hoist-room was the general routine work of this haulage held up.

Jan 1, 1941

By D. Raicevic

Interest has recently been revived in the recovery of tantalum from the Bernie Lake pegmatite deposit. A gravity concentration process was developed to give satisfactory recovery and concentrate grade. The application of high-intensity magnetic separation was also stud1ed. A pilot-plant investigation that confirmed the laboratory testing and provided a commercial-grade concentrate 1s described.

Jan 1, 1968

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By J. M. Cummings

DURING the past year, the writer has investigated the treatment of a variety of British Columbia tungsten-bearing ores. Much of the test-work described in this paper was carried out in collaboration with Mr. A. G. Lyle in association with the British Columbia War Metals Research Board at the University of British Columbia. The remainder was completed in the laboratories of the Department of Mines at Victoria. Two mills in the Province are at present treating tungsten ores. Descriptions of these are included through the co-operation of Messrs. S. Gray (1) and A. A. Almstrom (2). MINERALOGY, OCCURRENCE, AND SPECIFICATIONS In the present paper, attention is directed solely to scheclite, inasmuch as known occurrences of other tungstcn minerals in British Columbia are of mineralogical interest only. The properties of scheclite are listed below: Percent W03 .. 80.6 Tenacity ...... Very brittle Çrystallization Tetragonal Lustre ........ Vitreous to resinous Cleavage ...... Good in 4 directions Magnetism ... Non-magnetic Specifie gravity 6.05 Diaphaneity .. Transparent to translucent Hardness. . . . . . 4.5-5.0 Scheelite may contain as much as ten per cent of molybdenum in solid solution, but most of the specimens from British Columbia examined by the writer were relatively pure.

Jan 1, 1943

By R. Jacobs, R. E. L. Pobe

The Moab Khotsong Metallurgical Complex comprises a gold recovery circuit (Noligwa Gold Plant) and a uranium recovery circuit (South Uranium Plant). The metallurgical complex employs the reverse leach technology for the recovery of uranium; specifically, uranium extraction prior to gold using acid leaching processing. The inherent uranium species in the ore are uraninite, coffinite and brannerite. The slurry that has been subjected to the uranium leach is further subjected to solid-liquid separation to separate the uranium in solution through counter-current decantation and the solids (solids carrying all the gold), which are repulped and returned to the gold plant for gold processing. The uranium leaching process is critical to the uranium playing a pivotal role as a value adding by-product to the gold operation. The benefit of adopting this reverse leach process, for improved gold recovery, is that it exposes gold particles occluded within the uranium matrices and avails them for cyanidation. However, the drive for operational efficiency in uranium extraction must be weighed against the incremental operating cost against the backdrop of depressed spot uranium market prices. Over the years, efforts were directed at maintaining the benefit of extracting uranium to enhance gold recovery and simultaneously, optimizing the operating cost model for the uranium operation to remain relevant to the gold operation. The aim of this paper and the corresponding presentation is to give account of the uranium processing optimization journey embarked on over the years; namely, the operational trade-offs made in the process of ensuring that uranium continues to add value to the gold operation. These challenges were faced while striking a fine balance between processing cost and operational efficiencies against the prevailing depressed uranium spot market prices. Mineralogical- and laboratory tests conducted form the support basis for the results and observations articulated in the paper.

Jan 1, 2020

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"Abstract-The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek - Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern Black Hills or other areas of similar geologic settings."

Jan 1, 1995

By Alvis L. Lisenbee, Colin J. Paterson, Mustafa M. Hariri

"The schist-, sediment-, and intrusion-hosted Tertiary Au-Ag hydrothermal deposits of the northern Black Hills, South Dakota are localized and controlled by various types of fractures. This study is an attempt to distinguish between and discuss the possible causes of these fractures in three mines: Richmond Hill, Annie Creek – Foley Ridge (ACFR), and Gilt Edge.Five models based on the structural and tectonic settings of the northern Black Hills are proposed for the fracture origin. In Richmond Hill mine, mineralized fractures within the schist-hosted deposits are in the form of veinlets and stockworks. Larger veins filling open spaces along schistosity planes are also present. Fractures in Richmond Hill mine are related to breccia pipe emplacement and influenced by the Precambrian foliation.Fractures in sediment-hosted (ACFR) and intrusion-hosted (Gilt Edge) deposits are mode I systematic joints. These fractures, and similar ones examined in seven locations outside the mines, are related mostly to the formation of the Lead-Deadwood dome. Fracture trends vary from one area to another depending on their location with respect to the dome. Other factors, such as the Black Hills uplift, pluton emplacement, and Precambrian foliation, may also affect the fracture trends. The proximity of the mines to domes formed by multiple intrusions, the associated fracture patterns and density, and existence of breccias, may be used in exploration for similar deposits in the northern BlackHills or other areas of similar geologic settings."

Jan 1, 1995

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By F. J. Alcock

THE Magdalen islands have recently been attracting attention as a possible source of manganese. As early as 1880 small masses of manganese oxides were known to occur in the soil and at least one attempt was made to develop them. In 1939, after the outbreak of war, interest in the possibilities of the field was again aroused and during the winter of 1939-40 claims were taken up by two groups of Toronto interests. The islands also contain large quantities of gypsum. During the summer of 1940, the writer mapped the islands geologically, giving particular attention to a study of the manganese occurrences. For a base-map, the chart of the islands was enlarged to a scale of half a mile to an inch. Additional roads were added from traverses carried out in connection with the geological work, and form lines with approximate 100-foot intervals were put on from barometer readings. The geological map is the first that has been prepared of the islands. Previous Work In the summer of 1880, James Richardson of the Geological Survey of Canada studied the rocks of the islands and his r~port concerning them appears as Part G of the Report of Progress, 1879-80. In 1903, J. Obalski, Inspector of Mines for the Department of Lands, Mines and Fisheries of the Province of Quebec, visited the islands, chiefly to investigate the occurrences of manganese and gypsum, and his notes are found in the report on mining operations in the Province for that year. Around 1890, Robert Chalmers of the Geological Survey paid a visit to the islands, and his observations, which chiefly concerned the surface geology, appear in the Annual Report of the Survey, Vol. VII, 1894, Part M, p. 94. The next geological work was carried out by John M. Clarke, Director of the New York State Geological Survey. Clarke paid many visits to Gaspé peninsula between the years 1900 and 1920, collecting fossils and gathering h1s~orical data, and extended his investigations of Gaspé county over to the Magdalens. His Observations on the Magda/en Islands is included in the New York State Museum Bulletin 149, seventh report of the Director, 1910.

Jan 1, 1941

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By N. Aslin, G. Heferen, H. DeWaal

"Mount Isa Mines (MIM) acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry starting in the 1978’s through until the early 2000’s. The ISAPROCESSTM tank-house technology has been licensed to copper refineries throughout the world, and a significant per cent of the world’s copper is refined using this technology. Since development in the late 1980’s more than 20 ISASMELTTM copper and lead smelting furnaces are now installed in countries around the world. Jameson Cell flotation technology developed jointly by Mount Isa Mines and Professor Graeme Jameson is widely used in the Australian coal mining industry and increasingly in the base-metal and gold industry. The IsaMillTM’s developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies and has been successfully implemented into base metal fine grinding applications around the world. The most recent commercialised innovation is the atmospheric leach Albion ProcessTM with its supersonic HyperSpargeTM gas sparger, is being adopted as a solution to the increasing complexity of orebodies. MIM’s contribution to the industry was significant given the size and the remote location of its operations with Townsville Copper Refineries more than 1350 km and Mount Isa 1800 km from the nearest state capital of Brisbane. This paper will briefly discuss the development of each of these technologies and why MIM – now owned by Glencore - was so successful innovating and developing such technologies over a period of nearly 40 years.INTRODUCTION Mount Isa is located in the Gulf Country region of Queensland about 1800 kilometers North West of Brisbane (see Figure 1). It came into existence because of the world class mineral deposits found in the area. In 1923 the orebody containing lead, zinc and silver was discovered by the miner John Campbell Miles. Mount Isa Mines Limited (MIM) was founded in 1924 to develop the minerals discovered by Miles, but production did not begin until May 1931. It paid its first dividend in 1947 after 16 years of troubled production. In 1954 the 1100 copper orebody was discovered and with rapidly rising reserves during the 1950’s and 1960’s led to the construction of new concentrators to treat lead/zinc/silver ores in 1966 (#2 concentrator) and copper ore’s in 1973 (#4 concentrator). The difficult nature of the Mount Isa lead-zinc orebodies has meant that the company had always needed to be at the forefront of mining technology. In the 1970’s through to the 1990’s, it became a world leader in developing new mining techniques and processing technologies as a response to declining metal prices and rising costs. Mount Isa has been smelting copper since 1953 and lead since the early 1930’s. Copper Refining at Mount Isa’s fully owned subsidiary of Copper Refineries Proprietary Limited (CRL) had commenced operations in 1959."

Jan 1, 2018

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

This paper describes the results of a laboratory study on the upgrading of Algoma siderite by the amine flotation of silica and silicate gangue. The experiments indicate that a virtually complete removal of silica is possible in a rougher flotation con-ducted in tap water at natural pH, without prior desliming of the ore. Grinding considerably finer than the apparent liberation size is essential for maximum silica rejection. A cationic collector, Aeromine 3037, gave best results when used in combination with a modifier. Of the several modifiers tested, a Dutch potato dextrin, Dextrin 4356, was found to be the most effective. Both iron recovery and the grade of the final iron product are enhanced by floating the pyrite contained in the ore prior to the amine flotation of the silica, and by scalping the magnetics from the silica concentrate. F OR over twenty years, the Algoma Ore Properties Division of The Algoma Steel

Jan 1, 1963

By Abhinav Karanam, Lukas Bichler

Yttria Stabilized Zirconia (YSZ) is a promising thermal insulator for high temperature environments due to its thermal stability and chemical inertness. As was demonstrated with other technical ceramics (e.g., Alumina), addition of Single-Wall Carbon Nanotubes (CNTs) to a ceramic matrix may significantly enhance the mechanical properties of the composite ceramic. In this work, 8 mol% YSZ with 0.2, 0.5 and 1wt% CNTs composites were prepared via Spark Plasma Sintering process. The densification, Vicker’s microhardness, specific gravity and microstructure evolution of the composites were investigated. The results suggest that the addition of up to 1wt% CNTs to YSZ yielded optimal combination of the studied properties. At higher addition levels, the specific gravity decreased and clustering of CNTs occurred, leading to poor densification and a relative loss of performance.

Jan 1, 2014