Search Documents

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By Marcondes Lima Costa

Abstract-The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes, and the younger ones on widespread hilly to flat lowlands. Both types show complete or truncated profiles, generally covered by deep yellow to brown topsoils. The mature laterite profiles contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic profiles. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature profiles. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epigenetic alteration types. The lateritic profiles show a well-developed ore zonation which is related to specific lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold; and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire profiles include titanium (as ilmenite and anatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly as ilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic profiles, has led to the formation of high-grade kaolin and refractory bauxites. The laterites in the Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By Marcondes Lima Costa

The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes,and the younger ones on widespread hilly to ?at lowlands. Both types show complete or truncated pro?les, generally covered by deep yellow to brown topsoils. The mature laterite pro?les contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic pro?les. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature pro?les. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epi-genetic alteration types. The lateritic pro?les show a well-developed ore zonation which is related to speci?c lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold;and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire pro?les include titanium (as ilmenite andanatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly asilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic pro?les, has led to the formation of high-grade kaolin and refractory bauxites. The laterites inthe Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"The future of Polish copper mines KGHM Polish Miedz S.A. will be associated with mining at depth. At present, technologically advanced measures are being introduced to minimize the adverse influence of the environmental hazards on people working underground. Polkowice-Sieroszowice mine is the only mine in Poland where mining takes place in copper and salt deposits. On the basis of the current and anticipated methods of ventilation of a selected ore deposits the paper will analynze a number of solutions enabling planned mining of copper ore deposit, while minimizing the impact of natural aerological hazards in working areas. INTRODUCTION The future of copper ore mining, carried out by KGHM Polska Miedz S.A., will be based on mining from continuously greater depths (Butra, 2015). It is forecast that this will be accompanied by an increasing climatic hazard, resulting from an increase in the original temperature of rocks of more than 45°C as well as gas and geodynamic hazards (Soroko, 2015; Andrusikiewicz, 2015). Due to the safety of underground teams, a need arises to develop methods eliminating the adverse impact of the natural hazards, down to a level enabling the mining activity to be carried out on an industrial scale while maintaining favourable economic parameters. Current depths of the copper ore deposit being developed are effectively verifying the technical methods and measures employed to date for eliminating the natural aerological hazards. Amounts of air supplied to mining areas, with lengthy transport routes, are becoming insufficient for miners’ temperature safety, whereas increasing the power of cooling air-conditioning stations for cooling the air undermines the economic legitimacy. However, along with the temperature hazard, a significant problem at the current depths is an increase in gaseous occurrences in the headings’ areas. The concentrations of natural harmful gases found, even with the values below the permissible concentrations, in the case of limited amounts of air and/or low airflow rates, may pose a considerable danger to the workers. The hazards referred to are currently the major factors determining the advance of headings, above all in mining sections, being the outcome of geological structure and depth of lying of a deposit. However, at the current depths of mining minerals from deposits, room-and-pillar mining systems employed also have a decisive impact on the increase in natural aerological hazards."

Jan 1, 2019

By Clermont Lavoie, Marc Filion, Marcel Vallée

"Les mineralisation d'or des gîtes de la SOQUEM - Silver Stack dans is canton Bousquet se situent dans une bands de roches pyroclastiques asides du groupe de Blake River, d'âge archéen, dans le même horizon géologique que lee gites aurifères de Thompson Bousquet et Dumagarni situés plus a rest. La propriété a été explores anterieurement a maintes reprises depuis les années 1930, parfois jusqu'aux travaux souterrains, notamment par les groupes Mooshla, Warrenmac et Westwood Cadillac ainsi que par Silver Stack Mines.Ces zones auriferes se situent a l'intérieur de larges halos (jusqu'à 1,000 m x 400 in) de pyrite disséminée (2-5%) dans des tufs a lapilli et des agglomerate acides montrant des concentrations locales de pyrite. La zone 1, découverte en vérifiant par sondage une anomalie E.M., coincide avec une de ces concentrations de pyrite et la teneur en or est ici proportionnelle a la pyrite. Ce secteur se distingue par l'intensité de l'altération en séricite. La zone 2, qui s'étend sur près de 600 m, se situe dans un agglomérat acids, avec une faible teneur en pyrite, et montre de fines veinules de quartz-carbonate.Du point de vue géophysique, aucune methods ne donne des résultats probants: la polarisation provoquée montre de tree grandee anomalies correspondant aux halos de pyrite, tandis que lee concentrations de pyrite détectées par les méthodes E.M. (VLF ou EMH) sont loin d'être toutes aurifères. Les relevés magnétiques aident a établir la structure la où un certain contraste de susceptibilité magnétique est present. Les essais minéralurgiques préliminaires indiquent que la concentration de Bette mineralisation aurifère ne présentera pas de problems majeur."

Jan 1, 1977

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By A. Aftabi

To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples areanomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb(>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2in the southern part of the area. The strong Cu-Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry cop-per mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sul?de mineralization is present.

Jan 1, 1997

By A. Aftabi

Abstract-To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2 at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1 ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples are anomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb (>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2 in the southern part of the area. The strong Cu- Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry copper mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sulfide mineralization is present.

Jan 1, 1997

By Francis Dakubo, Courtney Young, Avimanyu Das

"Hydrometallurgy of copper ores typically involve acid leaching followed by solvent extraction and electrowinning (SX/EW). EW is the final purification stage in which a voltage is applied across two electrodes causing the copper ions to reduce and deposit on the cathode. Applied voltages are near 2 volts with current densities around 300 amps/m2. In this study, research was undertaken to decrease the energy consumed in the EW process. To do this, various cell designs were constructed and tested in which a membrane was used to separate the cathode and anode compartments with concentrated solution from SX serving as catholyte and raffinate from SX serving as anolyte. Therefore, copper in the concentrated solution would be deposited on the cathode while ferrous in the raffinate would be oxidized to ferric at the anode. Because it is assumed that ferric acid leaching is used, resulting ferric would be recycled to the leaching process. A positive side effect of the envisioned process would be the elimination of oxygen evolution at the anode and thus the prevention of acid-misting. After a cell design was selected, it was used to test a number of variables: flowrate, concentration, temperature, ion-exchange membrane, and applied voltage. Following experiments in which variable ranges were determined, statistical modeling was conducted using STATEASE software. Optimal results indicate the voltage can be decreased to 1.5-1.7 volts with current densities of 300-400 amps/m2. Significant reduction in the energy consumption was accomplished by reducing the applied voltage. Furthermore, current efficiencies and copper production rates was increased by application of the membrane.INTRODUCTIONLeaching of copper ores is achieved using mostly sulfuric acid. The copper pregnant solution is contacted with an organic solvent or resin adsorbent which picks up copper ions as in Equation 1:"

Jan 1, 2016

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

By T. K. Bose

According to the Intergovernmental Panel on Climate Change (IPCC), the average global temperature has risen over the last century. If this trend continues over the next century, the IPCC projects a significant increase in temperature and a rise in sea level. The changes in climate could adversely impact human health, agriculture, water resources and ecosystems. Most national and international agencies have concluded that our use of carbon-rich fuel is responsible for global warming through the greenhouse effect. In the future, the situation may get worse if the increased need for energy in countries like China, India and Brazil is fulfilled by burning fossil fuel. Advanced natural gas-fuelled vehicles have the potential to reduce carbon monoxide and reactive hydrocarbon emissions substantially compared to gasoline vehicles. Further environmental benefits can be realized by using a blend of natural gas and hydrogen. Such an approach will help create an infrastructure for an eventual transition to hydrogen.

Jan 1, 2005

By T. Grammatikopoulos, K. Gibbs, H. De Souza, C. Gunning

The mineralogy of any ore body is a key factor in defining ore zones and predicting minerals/metals behaviour during processing. The determination of forms of gold, defined as the different chemical states in which gold is encountered in ore deposits, is critical. The most commonly known form is that of gold minerals and alloys, while other forms of gold have been collectively described in the literature as submicroscopic gold (i.e., less than 1 µm in diameter). Gold mining operations generally deal with very low-grade ores, in the order of a few g/t, in which gold displays complex mineralogy. These difficulties complicate the mineralogical studies and pose challenges for processing and recovering the gold. A comprehensive understanding of the chemical forms of gold is necessary to define gold mineralization and optimize gold metallurgy. SGS Canada Inc. has been using QEMSCANTM and a Tescan automated SEM that are automated mineralogical techniques that provide vast amounts of data for microscopic Au. The data in conjunction with other physical and chemical methods provide a comprehensive delineation of the ore composition and behaviour.

Jan 1, 2011

By M. M. Holgate

"Porosity neutron deflection scales can be derived more easily by cumulative correlation than by the conventional method of plotting corresponding points on a graph. The micro-log can be used as a porosity datum for the neutron log by transforming the permeability cut-off it shows to a porosity cut-off by a permeability-porosity function obtained from core analysis. Porosity footage values calculated in this manner from the neutron log are within 20 per cent of core analysis values."

Jan 1, 1960

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999