Search Documents

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By G. C. Baker

Despite the attention belatedly bestowed on tidal power in recent years, it remains largely a potential rather than an actual source of energy. The resource is, practically speaking, non-depletable. Extraction is technically feasible and environmentally acceptable. The restraints against development are economic, and they could be removed by technical improvements, changes in the cost or availability of other energy sources, or simply by a change in the cost of money. The exponential rise in the demand for energy makes it inevitable that the tides will be harnessed sooner or later.

Jan 1, 1972

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By Ahmad Ghahreman, James McNeice

"Cerium is the most abundant rare earth metal and is often found in deposits along with small amounts of more valuable metals such as neodymium and gadolinium1. As a result, the production of cerium oxide often exceeds market demands, thus in some cases it would make more sense to remove the cerium from the process solutions before further purification. A common method of cerium removal is to precipitate CeO2 from the acidic leach liquors by raising the pH to oxidize cerium(III) to cerium(IV). This study investigates the oxidation kinetics using three oxidants; hydrogen peroxide, sodium hypochlorite, and potassium permanganate. The effect of oxidant, pH, cerium concentration and temperature on the oxidation kinetics will be discussed. Cerium oxidation in solutions with pH ranging from 1.0 to 4.0 was investigated at cerium concentrations ranging from 2.0 g/L to 16.0 g/L. A cerium recovery of 40% can be achieved at different conditions with each oxidant at room temperature, with higher recovery at 60°C.INTRODUCTION Over the last 70 years, the rare earth elements (REE) have become crucial components of modern technology. These metals are categorized as light rare earths (LREE) or heavy rare earths (HREE) by governments and miners based on weight, abundance, and therefore value. The minerals bastnaesite, monazite, and xenotime compose the majority of the world?s exploitable sources of these metals (Binnemans, 2013; Parker and Baroch, 1971). Geologists classify the LREE ores as „cerium group? minerals, approximately 50% cerium oxide by weight. The cerium group minerals monazite and bastnaesite compose the majority of world production, leading to an overproduction of cerium relative to world demand. This ratio of light to heavy REE in deposits has led to a phenomenon referred to as the balance problem (Binnemans et al., 2013). As an example, to produce 1 tonne of europium oxide from a bastnaesite deposit 450 tonnes of cerium oxide must be processed. This means that any push to increase production and access the value of the HREE metals will drive down the value of the LREE metals leading to diminishing returns (Zepf, 2016). These ores also contain measurable levels of thorium, subjecting them to complex radioactive waste regulations. During the 20th century, the USA was the largest producer of rare earth metals (REMs), primarily sourced from the Mountain Pass mine in California. However, due to a combination of market dynamics and regulations, China has dominated the market for the last two decades. The largest Chinese REE mine, Bayan Obo, produces rare earth (RE) concentrate as a byproduct of iron mining, decreasing their relative production costs (Gupta and Krishnamurthy, 2005). This mine alone represents about half of world bastnaesite production (Zhi and Yang, 2014). Rising demand for high-tech products has forced Chinese producers to commission other large mines, climbing to 90% of world production in the early years of the new millennium (Mancheri, 2016). This presents the west with a looming supply risk of these critical metals in the future."

Jan 1, 2017

By Fathi Habashi

The year 1987 marked the centennial of the beginning of modern hydrometallurgy. On October 19, 1887 British Patent No. 14174 entitled Process of Obtaining Gold and Silver from Ores was issued*. The discovery was made by John Steward MacArthur (Fig. 1), a chemist-metallurgist, supported and assisted by Robert and William Forrest, two brothers practicing medicine in Glasgow. The discovery was made in the basement of their clinic. The process, which became known as the cyanidation process in reference to the alkali cyanide reagent used, immediately received industrial success in New Zealand in 1889 and in South Africa in 1890t. It displaced the chlorination method which had been in use. In 1903 MacArthur was awarded the first Medal of the Institution of Mining and Metallurgy in London1131 - The cyanidation process was responsible for the doubling of gold production in the world in the two decades which followed its first application (Fig. 2). To the modern metallurgist, it may be surprising to think of MacArthur coming across an obscure reagent such as an alkali cyanide as a leaching agent for gold ores. It is the purpose of this paper to discuss the background and the factors that led to this invention, the development of the understanding of the process, and the application of modern technology.

Jan 1, 1999

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940's has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

By Ian R. Morrison

"Abstract - The Izok Zn-Cu-Pb-Ag volcanogenic massive sulfide deposit is located 265 km south of Kugluktuk (Coppermine), Nunavut Territory, Canada, in the west-central Slave structural province. The Izok deposit is owned 100% by Inmet Mining Corporation and represents one of the largest undeveloped zinc-copper resources in North America. The Izok deposit is hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks of late Archean age. The hanging-wall stratigraphy includes additional felsic volcaniclastic rocks, andesitic and basaltic flows, thin sulfide-rich iron formations, and turbiditic sedimentary rocks. The felsic volcanic rocks are intruded by intermediate dikes and sills, followed by gabbroic dikes and sills. Both intrusive suites are interpreted to be volcanic feeders to the overlying flows. All lithologies are subsequently cut by younger, irregular, granitic pegmatite and diabase dikes. The volcanic and sedimentary rocks are regionally metamorphosed to pyroxene hornfels grade. The massive sulfides occur within a large (kilometer-scale) Na-depleted sericitic alteration zone. The immediate footwall and hanging-wall rocks to the deposit are characterized by zones of muscovite- biotite-sillimanite, lesser chlorite-biotite-cordierite, and locally intense silicification and sodium metasomatism. All lithologies have been affected by younger Ca-metasomatism. As currently defined, the Izok deposit comprises a cluster of five complexly zoned composite lenses: the Northwest, North, Central West, Central East, and Inukshuk lenses. The first four lenses are amenable to open-pit mining, whereas the Inukshuk lens will require underground development. The total indicated mineral resource presently stands at 16.5 million tonnes with a grade of 2.2% Cu, 11.4% Zn, 1.1% Pb, and 60 g/t Ag. Inmet Mining Corporation is presently reviewing the economic feasibility of developing the property."

Jan 1, 2004

By John J. Jonas, Hong Qin

Cylindrical samples of pure titanium were subjected to uniaxial compression at room temperature, leading to the formation of three generations of twins. Many primary contraction twins were observed as the initial texture was favourable for their formation. Numerous secondary extension twins formed within the primary contraction twins and some tertiary contraction twins within the secondary extension twins. The orientations of these three generations of twins were determined by electron backscatter diffraction techniques and their associated Schmid factors (SFs) were calculated. The formation of the twin variants selected in each generation and the absence of certain potential variants are accounted for by rotating the twinning displacement gradient tensor expressed in the twin system reference frame into the crystallographic reference frame of the relevant neighbouring grain. The presence of the observed primary, secondary and tertiary twins is explained in terms of the ease of imposing the required accommodation strains on the neighbouring grains. By contrast, certain first, second and third generation potential high SF twins were absent because their formation would have required accommodation by the most difficult deformation mode: pyramidal glide.

Jan 1, 2015

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

By A. J. Sinclair, N. Champigny

"The Cinola gold deposit in the northern Queen Charlotte Islands, British Columbia, is in a clastic sequence consisting of a lower shale of the Late Cretaceous Haida Formation and an overlying interbedded sequence of pebble conglomerate and coarse-grained sandstone of the Middle Miocene Skonun Formation. Both formations are intruded by a stock and dykes of porphyritic rhyolite. Two K-Ar model ages indicate mineralization and probably porphyritic-rhyolite intrusion at about 14 Ma (middle Miocene). A splay of the Sandspit fault system constitutes the footwall on the west of the deposit.The Cinola deposit can be classed as Carlin-type based on features such as (1) small particle size for gold, (2) Tertiary age of mineralization, (3) element abundances (e.g. high Hg), (4) dominantly argillic alteration, (5) a structural setting associated with major faults, (6) porosity of the host rock and (7) spatial and possibly genetic association with felsic intrusions. Gold is widespread and occurs mainly as grains of< 0.5 11-m in silicified sedimentary rock, and in quartz veins. Locally, coarse > 100 11-m particles of native gold occur in quartz veins, especially in strongly brecciated porphyritic-rhyolite. Ore minerals are mainly pyrite and marcasite, but include small amounts of chalcopyrite, sphalerite, galena, pyrrhotite, cinnabar, tiemannite (HgSe), rutile, magnetite, hematite and limonite in addition to native gold and electrum. No silver minerals have been found; silver was found in gold particles in amounts varying from 6.2 to 24.2 weight per cent. Alteration products are sericite, illite, kaolinite and chlorite, with abundant quartz of several stages.The host rocks, specifically the Skonun Formation, formed as an alluvial plain facies in a braided river system discharging into a marine basin in early Middle Miocene time. During the Middle Miocene, this sequence was intruded by a rhyolitic stock. The highly porous and permeable Miocene clastic sequence apparently provided an optimum setting for the development of a large geothermal system, the energy for which probably derived from the rhyolite stock. Mineral deposition followed a well-defined paragenesis, which, from oldest to youngest, is: (1) precipitation of iron sulphide minerals, and early quartz; (2) several stqges of quartz veins, with deposition of sphalerite succeeded by galena, chalcopyrite and visible gold. Micron-size gold was precipitated throughout these two stages of mineral deposition. Argillitization of the host rocks probably in part coincided with the mineralization and continued during cooling of the geothermal cell.In-situ reserves have been estimated at 41.1 million metric tons averaging 1.85 g Au/tonne using a cutoff grade of0.86 g Au/ tonne."

Jan 1, 1982