Search Documents

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),

By David B. Brooks

INTRODUCTION Resources are not; they become (Zimmermann 100) . The companion concepts of reserves and resources appear, one way or another, in almost all considerations of mineral supply. Yet, no other concepts in the economics of the mineral industries have occasioned so much confusion. Whereas everyone agrees that in general the terms refer to the amounts of material that-depending upon technology, market conditions, and institutions-will become available for production in the near or more distant future, the apparent agreement disappears when we come to more specific definitions or to application of the definitions. Some definitions emphasize the physical aspects of reserves and resources, while others emphasize the economic. Some treat reserves and resources as fixed quantities, while others regard them as continually varying. Some consider that reserve and resource estimates have validity only for individual deposits, while others insist that they can be measured with sufficient accuracy for regional or national planning. This confusion in concepts that lies at the very heart of mineral economics is both strange and not so strange. It is common in the social sciences to find concepts that have been adopted into scientific jargon from popular usage and given rather special meanings -at the same time that they continue to be widely used without such qualifications. Psychologists have the same trouble with personality and sociologists, with community. Nevertheless, an attempt must be made to straighten out the various meanings of reserves and resources, or at least to clarify the conditions under which different meanings are applicable, before much progress in analysis of mineral problems can be expected. That is the objective of this chapter. Throughout the chapter, an attempt has been made to provide enough references to guide the interested reader to the most pertinent works on the concepts under study. However, even in a review article, it is no longer feasible to provide a comprehensive set of citations; there are simply too many. In many instances the works cited will themselves include the bibliographies needed to complete a literature search; those that are particularly useful in this respect are so noted. Also, because of the limited availability of foreign periodicals, some important works -originating largely in Canada, France, the

Jan 1, 1976

By J. Jones-Parra, R. S. Reytor

The porosities of fractured limestone reservoirs can be divided into two broad types in accordance with their effects on fluid distribution and fluid flow. In the coarse porosity, gravity segregation lakes place freely and the resistance to fluid flow is very small. In the fine porosity there is no segregation and a high resistance to flow, and it has relative permeability characteristics similar to tight sandstones. By analyzing the affect of the two porosities it is concluded that in some cases to recover the maximum amount of oil it is necessary to remove large quantities of gas from the reservoir by producing at high gas-oil ratios. In this manner the fine porosity is drained of its oil and the gas-oil contact drops slowly permitting higher production rates from the oil leg. Since this conclusion is contrary to widely accepted principles of conservation, a mathematical model (Fig. I) was constructed to duplicate the conditions desired. The behavior of the model indicates that under certain conditions it is possible to recover more oil by producing at high gas-oil ratios than by production at low gas-oil ratios, and that the rate of production is affected more by gas shut-offs than by the decrease in pressure (Figs. 2, 3, 4 and 5). INTRODUCTION It has been noted that certain limestone reservoirs behave in such a way as to indicate that there are two distinct types of porous spaces available for fluid storage and fluid flow. Regardless of the nature of these porous spaces the distinguishing characteristic is that in one type of porous space there is definite gravity segregation between the oil and the gas; while in the other, the gas evolved tends to remain distributed equally throughout the reservoir. For the sake of simplicity the porosity in which gravity segregation takes place at a fast enough rate to affect the behavior will be called "coarse po- rosity", while that in which this is not so will be termed "fine porosity". The behavior of a reservoir of this type would be different than that of a sandstone reservoir, especially if most of the oil is in the fine porosity. It has been observed that fluid flow to the wells takes place mostly through the coarse porosity. The large fractures which

By C. R. Wohrman

A melt of pure electrolytic iron with about 0.4 per cent. sulfur and 7 per cent. manganese was prepared in connection with a study of inclusions in iron. The alloy darkened rapidly when etched with a 10 per cent, alcoholic solution of nitric acid, and microscopic examination revealed the presence of a semimartensitic, semi-Widmanstättian structure (Figs. 1 and 2) closely resembling the structures found by Benedicks in his artificially prepared "meteoric iron."&apos; The structures found by Benedicks were readily explained by the presence in his alloy of the two well-known iron-nickel solid solutions, taenite and kamacite, and of their eutectoid (?) aggregate, plessite. By analogy, one would infer the existence of similar phases in the iron-manganese alloy just described, such an inference being strengthened by the similarity displayed in many ways by nickel and manganese in their effects on iron. Iron-manganese Alloys are Regarded as Homogeneous Heterogeneity of iron-manganese alloys has not been recognized heretofore, judging from the data of standard metallographic books and those of original papers. In fact, iron and manganese are quite generally regarded as completely miscible in the solid state. Dr. Rosenhain,2 for example, writes: Alloys of group (a), of which those of gold-silver, iron-manganese, and copper-nickel are examples, when allowed to crystallize sufficiently slowly to attain their condition of final equilibrium, present a microstructure exactly similar to that of a pure metal—the homogeneous character of the molten solution is in that case so completely maintained that the microscope cannot detect the presence of any second constituent. Guillet and Portevin3 refer to the iron-manganese system as an example of the "case of metals completely miscible in the solid state."

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world&apos;s total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates (or sodium-free compounds) are required for certain end uses, but in general, nonsodium borates are used only where borax is not avail- able. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of about a million tons of B2O3. Leadership in supplying borates has shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates. In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, Calif., is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, Calif., the world&apos;s leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "lo-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7- lOH2O. In addition to ship- ping all major refined borate products from Boron, the company ships semiprocessed ore concentrates to treatment plants elsewhere.

Jan 1, 1975

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By F. W. Schaller

TETRAGONALITY is an important aspect of the models of transformation, strengthening, and tempering of ferrous martensite. When the c/a

Jan 1, 1963

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By C. A. Stiles, J. W. Nyhus

Erie Mining Co. is a 10.3-million-tpy pellet producer on the east end of the Mesabi Range 60 miles north of Duluth. Its complex includes facilities for mining, crushing, grinding and beneficiation in addition to a pellet plant and power plant. A 74-mile railroad links the mine and plant to Taconite Harbor on the shore of Lake Superior. The concentrate recovery ratio at Erie is about 1: 3, and this, along with stripping activity, makes it necessary for the company to mine nearly a million tons of material a week. At the outset, all crude ore mined at Erie was hauled entirely by rail, but with expansion into additional mining areas, the company made a gradual transition towards truck-to-rail haulage. Today, in Erie&apos;s 11th year of operation, over 50% of all crude taconite mined is transported by truck to loading pockets where it is transferred to rail cars. Future years will see more taconite moved in this manner. Thus, the company has an increasing interest in tire performance.

Jan 6, 1969

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929

Four years of intensive exploration effort by Newmont Mining Corp. came to a climax May 27 in Carlin, Nevada, when local, state and federal officials joined with company officers at a dedication ceremony saluting the start-up of the firm&apos;s wholly- owned subsidiary, Carlin Gold Mining Co. Before an invited audience at the plant site, Newmont&apos;s President Plato Malozemoff and Nevada&apos;s Senator Howard D. Cannon pushed a lever and watched the new melting furnace rotate until a brilliant orange-red stream of molten gold poured forth from its mouth. Two 1200-oz bricks of bullion were poured that day, and they are the first of many that will lift this mine into the number two slot among U.S. gold producers and fourth among all gold mines on the North American continent. Although Newmont Mining first entered the gold mining business in 1929 in Grass Valley, California, the Company had operated no gold producers since the well-known Government directive L208, issued in 1942, closed down U.S. gold mines for the duration of World War 11. Now it is back in the business in a big way-a $10 million mine and plant capable of producing 200,000 oz. per year. All the gold from the Carlin operations is earmarked for the U.S. Mint in San Francisco.

Jan 7, 1965

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10&apos;* sec-&apos;). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.&apos; Several investigators&apos;-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.&apos; From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800&apos; to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture&apos;, 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967