Search Documents

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

By R. F. Yap, N. Arbiter, C. C. Harris

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give substantially constant power numbers in liquid systems indicating that they operate close to fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufacturers. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles, drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations. The modern mechanical flotation machine has, over a period of 60 years, displaced other designs to become the dominant type. Once the correct chemical environmental conditions have been established, the major requirement, selective mineral-air adherence, is essentially a function of two operating variables — impeller speed and air rate. The special nature of this dependence is such that in the same apparatus, but under different operating conditions, adherence can be either prevented or destroyed. Another aspect of this observation is that flotation machines though differing in detail to a considerable extent can produce similar metallurgical results. It must be concluded that having determined the correct reagent levels, establishing the correct operating conditions are at least as important as machine design. Since about 1960, after 30 years of fairly stable circumstances, manufacturers have been developing new types of machines whose major feature is emphasis on pulp flow characteristics by virtue of new im-peller-stator designs. As far as can be ascertained, these new designs necessitate radical departures from accepted impeller speed-air rate values. Performance data are still awaited. Flotation machine development has been empirical, as is selection of operating conditions. The purpose of the work at Columbia University has been to elucidate the fundamentals of the subject so that the purely mechanical aspects of the flotation process can be understood in hydrodynamic terms.1-6 Hopefully, this might lead to intelligent selection of a particular machine and its operating conditions for a specific ore based on a minimum of testing, or even to new types of flotation machines. The present investigation is the most comprehensive to date.7,8 Earlier work, which was largely exploratory, has been repeated and extended and employes the most accurate measuring techniques available. Additionally, sufficient hydrodynamic data were obtained under flotation conditions to delineate the relevant operating ranges. Attention has been given to scaling in that several geometrically scaled tanks and impellers have been constructed and tested; it has been pointed out elsewhere that undistorted geometrical scaling rarely pertains in flotation machine design.5 This paper is divided into sections dealing with relevant combinations of the three phases: liquid, air and solid. Summaries of the literature have been given in previous publications2-4 and will not be repeated here. Recently, several reviews of mixing have appeared, which can be usefully referenced.9-11 It is of interest to note that flotation is not included

Jan 1, 1970

By William Mikulas

LITTLE work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn, and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallo-graphic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic com-pounds, and three of the structures were partly determined. No attempt was made to determine the range of homogeneity of the inter-metallic compounds.

Jan 1, 1937

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By Charles A. Kliche

INTRODUCTION The Northern Great Plains Coal Province which occupies approximately 36.6 ha contains about one-half of the nation's total coal resources. About one million ha are underlain by coal that is considered to be mineable from the surface. The topography of the province is predominately plains, rolling hills, and some badland areas characterized by breaks or sharply eroded hills. Elevations range from about 1500 m above sea level on the west to about 600 m above sea level on the eastern boundary. The average slope of the ground is approximately 2 m per km. Streams in the province drain generally easterly and southeasterly (1). In the United States, the Northern Great Plains Province lies within the states of North Dakota, South Dakota, Montana, Wyoming, Nebraska, and Colorado. The coal within the province is located almost entirely in the states of North Dakota, Montana, and Wyoming. Although it is relatively low rank, the coal within the province encompasses a large portion of the total remaining U. S. reserves. The U. S. Geological Survey estimates the total remaining coal resources of the United States to be 2.6 trillion mt within 1000 m of the surface, and 2.9 trillion tons within 1830 m of the surface. Of this total, only about 177 billion mt are classified as reserves meaning that they are (1) known in location, quantity and quality from geologic evidence supported by engineering measurements, and (2) economically recoverable based on currently available technologies and current market value (2).

Jan 1, 1983

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer's impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

1. How Does One Determine Whether an Ore Body Will Block-cave? Page Mark A. Smith......... 122 Harry A. Leidich........ 122 McHenry Mosier ...,.. 22 R. W. Hughes ........ 122 Sherman R. Burdick ....... 123 R. T. Gallagher........I 23 Benjamin F. Tillson...... 123 Lucien Eaton...........123 C. F. Jackson..... . .. 123 Philip B. Bucky........... 126 2. How Does One Determine the Block Dimensions and the Development Work Necessary to Make an Ore Body Cave? Mark A. Smith... 125, 127, 129 Harry A. Leidich..........126 McHenry Mosier......126, 127, 132 R. W. Hughes...........126 Sherman R. Burdick.........127 R. T. Gallagher...........127 Benjamin F. Tillson......127,131 L. E. Young............127 Robert D. Hoffman.......128, 132 Gerald Sherman..........128 Philip B. Bucky......130, 131, 132 K. S. McClellan..........132 Tell Ertl.............132 3. How Do the Forces Act and What Are the Stresses Developed in a Block That Cause It to Block-cave? Mark A. Smith.........132, 135 Harry A. Leidich........133 McHenry Mosier . .. 133 R. W. Hughes ....... 133 Sherman R. Burdick..... . 133 R. T. Gallagher..........134 C. F. . Price, Jr. ........134 Benjamin F. Tillson.........134 C. F. Jackson......134, 135,137 R. Taborelli...........135 Frank A. Ayer ... .....136 Philip B. Bucky . .........136 Rollin Farmin . . .......136 . . . Weysser.....135, 136, 137 George S. Rice...........137 4. What Determines the Procedure in Removing Caved Ore? Harry A Leidich...........137 McHenry Mosier........137,141 R. W. Hughes...........137 Sherman R. Burdick........138 R. T. Gallagher...........138 Mark . Smith...........138 Philip B. Bucky......140,141,143 C. F. B. Price, Jr..........140 R. H. Bennett...........141 C. F. Jackson..........141, 143 Gerald Sherman..........141 Tell Ertl.............141 .. .. ..................143 C. H. Shoemaker..........143 5. What Are the Criteria for Determining the Efficiency of a Block-caving Operation? Harry A. Leidich.......... 143 McHenry Mosier......... 144 R. W. Hughes........... 144 Sherman R. Burdick.......144 R. T. Gallagher . ......... 144

Jan 1, 1946

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918

Discussion of a paper of S. S. Rummy and W. F. SCHWEDES, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2613 to 2635. K. A. PAULY, Schenectady, N. Y.-I have seen this installation and I wish all those interested in the question of electricity as a mine pumping agent could see it. It is not only a model for mine installation, but might well serve as a model for any electrically driven pumping plant. I think I am correct in saying that the pumps are the largest electrically operated centrifugal pumps in mine service in America. I talked with Mr. Rumsey in Duluth just before coming here, and he told me that the actual tests of the equipment as installed checked very closely with the shop tests; that the water delivered by the pumps was slightly in excess of the guarantee, something like 3 or 4 per cent., and that no troubles except of a very minor nature had been experienced with the installation from the start. One point which has been brought out by Mr. Rumsey, and by others who have looked into this question, is the marked saving which' can be made by the application of electricity to pumps, especially to the main sump pumps. The pumps are always located a long distance from the boiler plant and the losses in the steam mains are large. While many of the steam pumps are of a very high grade, yet the tests seemed to indicate that the steam consumption is extremely large. The reduction in operating cost of one small installation which I. have in mind pumping against a head of approximately 2,000 ft.-which by the way was a reciprocating pump-reduced the pumping cost to the neighborhood of one-fifth of the previous steam cost. . The high steam cost was probably due to leakage in the engine and the loss in transmission in the mine, the pumps being located almost half a, mile from the boiler plant.

Jan 4, 1915

By J. J. Becker

BEAN1 has discussed the magnetic behavior of mixtures of small ferromagnetic particles on the order of 20 to l000A in diam. As he points out, there are three size categories with characteristic properties: 1) Particles large enough to contain many ferromagnetic domains magnetize initially by the motion of domain walls. The initial susceptibility of such particles, if domain-wall motion is assumed to be perfectly easy, depends only on their shape. It is equal to the reciprocal of the demagnetizing factor (and is thus 3/4 tt for a sphere) and is independent of temperature. 2) Smaller particles find it energetically undesirable to contain domain boundaries. They are always spontaneously saturated, and reverse their magnetization only by rotation of their entire magnetic moment. As assemblage of such particles has a remanence which is a large fraction of the saturation of the assemblage; its coercive force is on the order of 2K/1,, where K indicates magnetic aniso-tropy from any source, and I, is the saturation magnetization of the substance of which the particles are made. 3) Particles which are still smaller continue to be single-domain, but the direction of their magnetization fluctuates thermally, as first pointed out by Neel.' They have no remanence and no coercive force and possess the temperature-dependent magnetization curve of a paramagnetic substance with a very large moment. Bean calls this superpara-magnetism. All of these kinds of behavior are observable in alloys consisting of a precipitate of ferromagnetic phase in a nonferromagnetic matrix. Fig. 1 shows a typical aging curve for the room temperature coercive force of a sample of 98 pct Cu-2 pct Co alloy

Jan 1, 1958

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By Lyall Zickrick

As a result of the studies on recrystallization and crystal growth made in this laboratory, certain theories have been developed. These are expressed briefly in a paper by Dean and Hudson.1 One of the principal points brought out in that paper is that in the deformation of a crystal, the energy supplied is distributed to the atoms of the lattice, probably by the forced formation of molecules. It is found that a Maxwellian distribution of the energy among these atoms will account for the grain growth at various temperatures. According to such a distribution the number of atoms with energy above a certain critical value, E, necessary for recrystallization at the absolute temperature T is given by n Ne(-E/kT) where N is the total number of atoms. It is apparent that if this line of reasoning is correct, a metal which has been cold-worked and reheated to a temperature below that of complete annealing will have the atoms with the higher energy recrystallized, that is, reduced to normal energy and there will remain only atoms below a certain energy. If this metal is again cold-worked the peak in the number-energy distribution curve will be displaced toward the regions of lower energies, that is, higher temperature of recrystallization. By a repetition of this process the position of this maximum and hence the recrystallization temperature of the metal could be raised considerably. In order to' check this theory, experiments have been made on copper wire. The wire was drawn from 1/4-in. rod to 22 B & S gage and then sample lots were annealed at 400 and 220° C., respectively. The wire annealed at 400° C. gave an elongation of 34 per cent., whereas that annealed at 220° C. gave only 23 per cent. These wires were then drawn by identical practice to 34 B & S gage and the elongation determined after an anneal of 3 mm. in an oil bath held at various temperatures.

Jan 1, 1927

By P. Shahinian, J. Weertman

Minimum creep rates of nickel samples were measured in the stress region of 2.5x107 to 2.8xl0 dyne per sq cm and the temperature region of 400° to 1100°C. The creep rate seems to be proportional to (stress) at stresses below 7x10H dyne per sq cm. The activation energy of creep is approximately 65,000 cal per mol. IN a recent theory' of steady-state creep which is based on Mott's dislocation climb mechanism, the following creep equation was derived for creep in polycrystalline metals (if where K is creep rate, Q the activation energy of self-diffusion, S the entropy of activation of self-diffusion, L' the grain size, L the subgrain size, b the length of the Burgers' vector of a dislocation, u the shear modulus, u the stress, a the critical shear stress, M the density of active Frank-Read sources, v the vibrational frequency of a vacancy, and kT has its usual meaning. This equation predicts a creep rate which depends on the stress through a power law at low stresses. At high stresses the creep rate increases much more rapidly with stress. The theory breaks down for stresses great enough that the inequality holds true. It was the purpose of the present in-

Jan 1, 1957

By G. B. Misra

While investigating on the aerodynamic resistance of airways supported with peripheral timber sets, at regular intervals, the following theoretical equations were developed by the author to estimate the resistance coefficient of such airways: [ ] for S < 1, where f is Darcy-Weisbach resistance coefficient of the airway, C is modified drag coefficient of the supporting member, D is equivalent diameter of the bare airway, 8 is ratio of the approach velocity over the sets to the average velocity of the bare airway, A is cross-sectional area of the bare airway, a is projected frontal area of the sets, A., is cross-sectional area of the air stream at the vena contracta inside the set, S is spacing of the sets, f, is resistance coefficient of the bare airway, l is length of aerodynamic influence of sets, p is perimeter of the bare airway, p, is setted portion of the perimeter of the bare airway, pe is unsetted portion of the perimeter of the bare airway, and P shielding factor. The equations were verified experimentally in a model rectangular airway supported with one- (bars), three-, and four-piece sets of square-section timber of three different sizes and were found to hold true. The work has been further extended to one-, three-, and four-piece sets of round timber of 2.6, 3.2, and 3.8 cm diam with the same experimental set up. Tests have been carried out for spacings of 25, 50, 75, 100, 150, and 200 cm over a regime of flow defined by the Reynolds number (with respect to the equivalent diameter of the bare duct) ranging from about 1.5 X 106 to 5 X 106 using the same experimental techniques. The values of f are calculated in the manner indicated in [Ref. 1]. Unlike with square-section timber, the resistance coefficient f of the airway setted with round timber shows a distinct variation with the Reynolds number of flow. This conforms to observations made by Sales and Hinsley.2 In order to have a comparable value of f for all types of sets with all sizes of timber, it was necessary to select the value of f at a fixed Reynolds number of flow. Since f is chiefly a function of the drag coefficient of the sets, the appropriate Reynolds number RE is that with respect to the diameter of timber in the set. Considering the diameters of timber used and the regime of flow over which measurements were made, f was chosen at a value of RE = 20,000 in all cases. The f vs. S curves are maximal in nature and in conformity with theory, the f vs. 1/S curves are straight lines up to a value of S = 1 beyond which they show a distinct flexure. The observed values of 1, the length of aerodynamic influence of sets, agree with the relation 1 = 42 e, developed for square-section timber sets, thus suggesting that the shape of timber has little influence on the length of aerodynamic influence. The value of the modified drag coefficient CD for round timber was calculated in the same way as for square timber in Ref. 1, taking the contraction factor Z = 1.5 for round-edged constrictions. CD has an average value of 0.96 with a standard deviation of 6.08% as compared to the free stream drag coefficient of 1.2 at RE = 20,000 for long cylindrical obstructions The shielding factor [ ] is plotted against S/1 in [Fig. 1]. The curves are more or less independent of the size of timber, but are different for the different types of sets, possibly due to their different degree of symmetry. Values of f calculated by the author&apos;s [Eqs. 1 and 2], using experimental values of CD&apos; and [ ] and taking I = 42 e, are plotted in [Fig. 2] against experimentally measured values of f for different types of sets with different sizes of round timber. The values agree closely with a standard deviation of only 5%, thus establishing the veracity of the theoretical equations developed by the author for round timber as well. A comparison was made between the Xenofontowa4 equations (the only other reasonable relations available for the estimation of the resistance coefficient of supported airways) and the author&apos;s [Eqs. 1 and 2] by comparing in [Fig. 3] the values of the resistance coefficient f computed by the Xenofontowa relations with those experimentally measured by the author. In order to make

Jan 1, 1975

By W. W. Beddow

TWENTY years or so ago I wrote an article on management which consisted mostly of a chart similar to thousands of others of that day showing line functions, staff functions, and the chain of command in a typical mining organization. Since hen we have been "bossing" from the faces to the swivel chair and we have made many errors of no little expense to our companies. We have kept the chart in mind but many times we have changed the functions to fit the people we have had to work with. Good management after all is getting results with the people, the equipment, the supplies, and the natural conditions of the coal seam or seams and adjacent strata present. We have made, with little effort, a good showing with average people and equipment in good natural conditions. We have made a miserable showing (although expending every personal effort) with better than aver- age people and equipment in bad natural conditions. In the latter case many of our stockholders felt that better management would have found some way to save their investment. Perhaps they were right.

Jan 1, 1944

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICHARD, Vice-Chairman D M LIDDELL Secretary, 7 Wall St.. New York. N. Y. C. A. BORN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON. Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 12, 1917