Search Documents

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Raíza da Silva Juvenal, Suelen Silva Rocha, Artur Ângelo Alcântara de Assis, Jorge Luiz Valença Mariz

Um estudo de viabilidade econômica deve considerar parâmetros e incertezas inerentes a um projeto para produzir resultados econômicos consistentes, fornecendo ao investidor uma ferramenta de tomada de decisão. O presente estudo objetivou efetuar inicialmente a avaliação econômica convencional do cenário realista de uma mineração de agregados em fase de implantação localizada em Pernambuco, cujo Valor Presente Líquido (VPL) obtido foi R$ 24.006.309,20, o que representa um resultado positivo. Através da metodologia de Monte Carlo foi efetuada uma análise de risco considerando incertezas em 100.000 cenários, nos quais nove variáveis assumiram valores estocásticos dentro dos domínios definidos, produzindo assim uma distribuição estatística do VPL ao invés de um único número, sendo ainda efetuada uma análise de sensibilidade para identificar e quantificar as variáveis que mais impactam no resultado da avaliação. Por fim, os dois fatores mais influentes identificados na análise de sensibilidade inicial foram isolados e submetidos a uma nova análise de risco em outros 100.000 cenários. Foi concluído que o projeto é economicamente viável e que a probabilidade de gerar lucro aos investidores é de 99,77%, embora a probabilidade do VPL ser igual ou maior que o previsto pelo método convencional seja de 49,98%.

Oct 3, 2019

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019