Search Documents

By Grant Buma

Groundwater restoration is an uranium leaching. Information on the technology, costs, and the current permitting regulations is of vital operators and to firms considering in important aspect of in situ effectiveness of the current state and federal government importance to in situ leach situ leaching. This study, funded by the U. S. Bureau of Mines, describes: (1) all recent restoration attempts at commercial in situ leach operations, (2) restoration costs reported by the industry, (3) empirical equations that predict the amount of groundwater flushing required to meet the current restoration criteria, and (4) in situ uranium permit requirements for the states of Texas, Wyoming, New Mexico, Utah, Montana, Colorado and South Dakota, and Federal requirements.

Jan 1, 1981

LAKE MARGARET is situate high up on the West Coast Range of Tasmania, and lies in a roughly triangular valley formed by the ridge of Mount Sedgwick on the south, the ridge formed by Mounts Geikie and Tyndal on the west, amid a ridge connecting Mounts Geikie and Sedgwick on the east. Any description of this hydroelectric installation, however brief, naturally divides itself into the following sections:1. STORAGE BASIN, &c. 2. DAM. 3. PIPE LINES. 4. POWER STATION. 5. TRANSMISSION LINES. 6. SUBSTATION 7. VARIOUS WORKS utilizing the power.The Storage Basin used is the natural lake itself, which has a maximum length of 110 chains, a maximum width of 40 chains, and a mean arelj. of 300 acres. The water-level of the lake, which has been maintained by a natural dam, is 2143 ft. above sea-level. The approximate catchment area at present appropriated is 7 sq. miles, and the rainfall, on the average, about 144 in. per annum. It is possible to increase this catchment area by suitable races, &c. Dam.-The dam constructed is of very small dimensions, and is not a storage dam in the usual sense of the term. The natural storage ot-the lake itself was used by means of a channel cut through the natural dam and thence to the mouth of the lake, the lake level being thus temporarily lowered while the outlet pipes, screens, &c., were placed in position, and the channel was then closed again with a concrete wall in which the pipes and screens are set. This channel was cut partly through rock and partly through sand and conglomerate boulders for a total...

Jan 1, 1915

By O Haavisto, N Khajehzadeh, L Koresaar

Online analysis of metal content can be used to optimise the grade and recovery of a flotation circuit. Compared to conventional laboratory analyses, the benefit of an online analyser is the speed of the measurement, therefore disturbances (eg changes in feed grade and decrease in recovery) can be reacted to in real time by an operator or automatic process control system. In some cases traditional X-ray fluorescence analysers can be applied to silica analysis in iron ore when the SiO2 grades are high enough and have a negative correlation with iron; however, generally a laser-induced breakdown spectroscopy (LIBS) analyser is more suitable for low Z elements.The Outotec Courier 8® analyser is a LIBS based analyser able to measure elements starting from lithium (Z = 3), thus being able to measure impurities; eg silica and aluminium directly in iron ore slurries. Besides online elemental analysis, the analyser can be combined with optical measurements for rapid continuous measurement of each sample line. Laboratory testing has also shown potential for mineralogical analysis using the combination of LIBS and reflectance spectroscopy.CITATION:Koresaar, L, Khajehzadeh, N, Haavisto, O and Timperi, J, 2017. Online elemental and mineral measurement of slurries in iron ore beneficiation, in Proceedings Iron Ore 2017, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By H. Tomlinson

"PURPOSE OF REPORTThe purpose of this report, which is the third of a. series on the coal mines of the Western States, is to give the findings of a study of the causes and methods of prevention of accidents from falls of root and coal in the mines of Lincoln County, Wyo. The three mines covered in this report, referred to as A. B. and C, account- for 9 per cent of the coal production in the county and nearly 9 per cent of the State's total production. For comparative purposes some statistical data are presented bearing upon the relation of injuries to their causes, to tonnage produced, to men employed, to days worked, and to days lost as the result of injuries.FATALITIES IN WYOMINGTo show the necessity for this study, Table 1 given the fatalities that occurred during 1928 in the bituminous—coal mines of the United States, of the State of Wyoming of Lincoln County, and in Mines A, B, and C, followed by a brief description of the Kemmerer coal dis-trict, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining timbering for roof support, roof testing, and supervision. All of these factors must be considered in any plan outlined to prevent accidents resulting from falls of roof and coal.ACKNOWLEDGMENTAcknowledgment is made to the officials of the operating companies for their cooperation and assistance during the study and collection of data to complete this report.GENERAL INFORMATIONLocation and Ownership The mines included in this report are within 18 miles north and south of Kemmerer, Lincoln County, Wyo. (fig. 1), and are owned and operated by various coal companies to supply the domestic, smelter and railroad markets. They are severed by branch lines of the Oregon Shorty Line Railroad Coal production and men employed underground in the three mines are indicated in essential detail in Table 2."

Sep 1, 1932

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

Calculations of the temperatures of metal, coke, and gas at any level in the cupola furn~ce can be carried out by means of heat balances, using data obtained from experiments with an 18 in. experimental cupola. The results can, to a certain extent, be verified by means of heat transfer calculations.The curves thus obtained, showing the variation of temperature with height in the cupola, provide a valuable picture of the heat transfer processes in a shaft 'furnace.INTRODUCTIONThe Brown Coal Research Laboratory, of the University of Melbourne, has been engaged in recent years on a programme of iron-melting tests in an experimental cupola furnace.Although the ultimate aim of this work is to develop brown coal char as a cupola fuel, most of the experimental work so far has been with conventional coke. The testing programme was designed to provide information on the effect of variables such as blast rate, metal-coke ratio, and coke size on the overall melting process, e.g. melting rate, temperature of metal tapped, and stack gas composition.However, in many cases data were obtained on conditions inside the furnace by measuring temperatures and gas compositions. The aim of the work described in this paper was to qevelop a method for using this data to obtain information on the processes taking place in the cupola.Very little research has been done on the combustion of fuels in shaft furnaces. Early work on this subject, as well as the initial stages of the Brown Coal Research Laboratory's programme, has been discussed by Evans (1959). The use of probes for obtaining information on conditions in the interior of a shaft furnace was pioneered by Belden (1913)...

Jan 1, 1963

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By Brooke T. Mossman

Asbestos fibers are highly fibrous silicate fibers that are distinguished by having a large aspect (length to diameter) ratio and are crystallized in an asbestiform habit that causes them to separate into very thin fibers or fibrils. These fibers are distinct from nonasbestiform cleavage fragments and may appear as thick, short fibers which break along cleavage planes without the high strength and flexibility of asbestiform fibers. Since cleavage fragments of respirable dimensions have generally proven nonpathogenic in animal studies, little data exists on assessing well-characterized preparations of cleavage fragments in in vitro models. The available studies show that cleavage fragments are less bioreactive and cytotoxic than asbestiform fibers. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestiform; Cleavage; Fibers; Fibrous

Jan 1, 2007

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978