Search Documents

By S. D. Dladla, S. Ramsamy

The majority of the tailings dam operations in South Africa will be required to comply with the new Global Industry Standard on Tailings Management (GISTM) within the next one to three years, depending on the dam classification and the requirements of the respective investors and insurers. With up to 72 auditable requirements, the implementation of the Standard needs careful planning and prioritization. This paper focuses on the practical steps to GISTM compliance for tailings facilities in operation in South Africa. The discussions are based on current practices, South African regulations, and industry standards requirements. The possible changes in dam classifications and the associated requirements are presented.

Jun 2, 2022

By Helen D. Robinson

Traditional practice to resist large lateral loads on foundations is the use of large diameter caissons, battered driven piles, or battered micropiles. Dense urban construction environments, however, limit the usefulness of these systems due to the close proximity of below- and above-grade obstructions. This paper presents two micropile construction projects in the United States where a complex scheme of battered micropiles and grade beams was developed to counteract large lateral loads at the foundation level. The paper also presents a procedure used to design vertical micropiles for large lateral loads, which can greatly simplify the design of foundations subject to significant lateral loads in urban environments. A design example shows a case where vertical micropiles were used to support allowable design lateral loads greater than 80 kip per micropile.

Jan 1, 2010

By J. H. Rhee, H. B. Ku, J. S. Lee, H. J. Park, B. S. Jang

A large wedge failure had occurred in the study area which was under construction. Therefore, in order to analyze the potential instability for this rock slope, the authors conducted numerical analysis with DEM and then the behaviour of rock mass was analysed after appropriate reinforce-ments were applied. Ein großer Keildefekt geschah in dem Untersuchungsgebiet, das im Bau befindlich ist. Deshalb, um die potentielle Unbeständigkeit für diesen Felsenabhang zu analysieren, führen die Urheber zahlenmäßige Analyse mit DEM. Und dann wird die Bewegung der Felsenmasse ana-lysiert, nachdem angemessene Verstärkungstruppen angewandt werden. Un grand échec de coin sèst passé dans le région étudié qui était en construction. Par conséquent afin d’analyser linstabilité potentielle de cette pente de roches, les auteurs ont mené une analyse numérique avec DEM. Ensuite le comportement de la masse de roches pourrait être analysée après les renforts appropriés étaient appliqués.

Jan 1, 2003

By BRETTMANN TRACY

Jan 1, 2000

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

This Kaiser Engineers report on the feasibility of surface mining on the North Slope of Alaska has considered the quantity and quality of the North Slope deposits with attention paid to the economic, technical, and environmental constraints of the mining systems suggested for the three candidate minesites at Kukpowruk River, Elusive Creek, and Kuk River. Site selection, based on coal rank and quality as well as seam thickness and geometry, also considered demonstrated and hypothetical reserves relative to three mining systems (dragline, shovel, dragline and shovel), mining equipment requirements, infrastructure, and transportation relative to the Arctic environment and costed for potential markets. Throughout the report the delicate permafrost environment has received particular consideration. Recommendations based on the technical, economic, and environmental feasibility of mining the coal deposits of Northern Alaska by surface mining techniques have resulted in two conclusions: 1. The coal deposits can be mined with currently available technology; 2. It is uneconomic to mine these coals given current coal resource estimates, costs, and market conditions. A literature survey is included in appendix.

Jan 1, 1977

By K. J. R. Ford, Botz. M. M.

Porphyry copper ores are frequently a source of low-grade gold ore, but gold in these ores is often associated with significant levels of cyanide-soluble copper. Cyanide leaching of such ores increases flowsheet complexity and operating costs, and requires thorough planning to satisfy environmental requirements for tailings disposal and mine closure. This paper presents a review of the chemistry of cyanide leaching of gold-copper porphyry ores, carbon adsorption phenomena and means of removing base metals from leach solution. The primary economic drivers behind the processing of such complex ores are also analyzed.

Jan 1, 2011

By C. O. Hawk

A PART of the Bureau of Mines effort to improve the conversion of coal to liquid fuels, batch autoclave tests were made on the hydrogenation of bituminous coal by a dry method, which featured charging the autoclave with dry ingredients only-coal, catalyst, and hydrogen. This innovation, which omitted the liquid vehicle used in earlier work, limited the products to those made from the coal charged. The effects of the common process variables (catalyst, hydrogen pressure, temperature, and residence time) were studied. Tin catalysts showed the highest activity in the widest variety of forms and were the easiest to disperse; dry mixing in the autoclave during the heating-up period usually sufficed. Ammonium molybdate, on the other hand, was inactive when dry mixed, but it compared favorably with the best catalysts known when applied by impregnating the coal with a solution of a molybdenum compound. As a group, metal naphthenates were the most effective; in fact, molybdenum naphthenate was the most active catalyst the Bureau tests disclosed. One-hundredth of a percent of molybdenum in this form (calculated as the metal in weight-percent of maf coal) induced 90-percent conversion of coal. However, because of their high cost, naphthenates have as yet only technical significance in coal hydrogenation. Long residence time and high reaction temperatures tend to increase the amount of thermal decomposition products formed (light hydrocarbon gases and/or char). High hydrogen pressure favors the production of liquids.

Jan 1, 1965

By William A. Hustrulid

The subject of surface mine development is large. This section covers the fundamental concepts involved in both the open pit mining of thick or steeply dipping deposits as well as the strip mining of thin, shallow, and relatively flat-lying seams or beds. Design involves the marrying of geometries, ore and waste characteristics, equipment, and economics so that the desired result is achieved. Generally, there are many possible combinations from which to choose. For example, extraction over a short time period requires one strategy while quite another is applied for longer times. Variations in supply and demand require some flexibility of operation. Customer requirements impose certain constraints regarding the set of possible designs. Over recent years, planning and operating considerations for surface mining imposed by environmental requirements have increased markedly. There have, at the same time, been enormous advances made in the design aids available to the mine planner. Computer simulation of the various options, whether it be for mine design or equipment selection, provides detailed information for decision making in real time. A significant challenge to the engineer/planner is how to best use the aids avail-able. Because of the widespread use of commercially available and in-house computer software by industry, this section does not deal with the details of planning (for basic coverage of mine development, see Section 7). Rather, some of the basic concepts are stressed. The principles involved in equipment sizing and selection are discussed. A highly important but sometimes over-looked aspect of planning, haul road design, is also covered. For surface mining operations of the future, in-pit crushing and conveying will become even more important. Some of the considerations for application evaluation are included. The section concludes with some future concepts for surface mining.

Jan 1, 2008

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By Raymond B. Ladoo

Talc is a hydrous magnesium silicate having the chemical formula H2Mg3 (SiO8 ) 4 ; it is often called steatite, soapstone or potstorie, and by the trade names talc clay, agalite, asbestine, and verdolite. The term talc may be used to include all forms of the pure mineral, whereas steatite denotes particularly the massive, compact variety, and soapstone the impure, massive form that often contains only 50 per cent of talc. Merrill 1 says: The name soapstone is given to dark-gray and greenish talcose rocks, which are soft enough to be readily cut with a knife, and which have a pronounced soapy or greasy feeling; hence the name. Such rocks are commonly stated in textbooks to be compact forms .of steatite, or talc, but as the writer has elsewhere pointed out, and as shown by the analyses here given, few of them are even approximately pure forms of this mineral, but all contain varying proportions of chlorite, mica, and tremolite, together with perhaps unaltered residuals of pyroxene, granules of iron ore, iron pyrites, quartz, and, in seams and veins, calcite and magnesian carbonates. When pure, talc is soft, having a hardness of 1, but when impure or when it grades into its varieties, the hardness increases to 3 or 4. Talc ranges in color from pure white and silvery white through gray, green, apple green, gray green to dark green, nlso yellow, brown, or reddish when impure. It is rarely, if ever, found in wellformed crystals, but often occurs in foliated plates or in fibrous aggregates. It is commonly compact or massive or in fine granular aggregates. Several analyses of talc from different regions ·are given in Table 1. Talc has several varieties, the most important of which is Rensselaerite. This variety, found in a small area near Gouverneur, St. La.wrence County, N. Y., is a hard, fibrous, -waxlike mineral having the same chemical composition as talc, but lacking its softness and its peculiar greasy feel. Its hardness and its peculiar fibrous form, even when ground, have made its grinding and separation a separate problem. In addition to the varieties of talc and soapstone, the mineral pyrophyllite or agalmatolite, a hydrous silicate of alumina, with the formula H2Al2 (Si08 ), is also mined and sold as talc. It resembles talc in color, feel, luster, and structure, and may be successfully substituted for true talc for most uses. In this paper it will be considered as one of the commercial forms of talc.

Jan 1, 1923

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By S. K. Bradford

(Pittsburg Meeting, March, 1910.) FOR years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually, many miles from an assay-office. If, upon examination, the formation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had " optioned" the property ! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged according to weight), and the fact that a few such trips would almost certainly wreck the outfit. For these reasons I began a process of elimination and substitution which finally enabled me to carry, in an ordinary 26-in. valise, sufficient apparatus and supplies for, say, 100 assays of adequate commercial accuracy. My final outfit was as follows: APPARATUS. Small hammer; steel mortar (2.5 in. wide, 3 in. high, with stand sawed off flat, so that it can be used as an anvil and for

Jan 1, 1911

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By H. Ito, T. Takasu

Effects of a mechnochemical treatment to oxide Ni ores have been investigated to enhance the extractive ratio of Ni from them in acid leaching process. High intensity grinding by a planetary boll mill showed strong effect to enhance the extractive ratio of Ni, for example , 10% of extractive ratio of Ni in sulfuric acid leaching(0.05mo1/1,at room temperature) increased to more than 90% with 60min. of planetary boll milling. Effects of additives(sulfur and some oxidants) on the mechnochemical treatment have also studied. Sulfur showed almost no effect to enhance the total Ni extractive ratio but increases the selectivity of Ni extraction. More than a half of Ni could be extracted by water when Ni ore was grinded at addition of Na2S207 in the milling treatment. Some effects of mechnocemical treatments to Ni ore are summarized in this paper.

Jan 1, 2005