Search Documents

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By AIME AIME

AT the annual .meeting of the Minnesota Section in December, Dr. Leith characterized as a question still open the exact method of origin of Lake Superior iron ores and emphasized it as an important practical problem for the future. He welcomed the step taken last year by Dr. Gruner in presenting a new hypothesis, and asked Lake Superior geologists to meet the challenge of such multiple hypotheses by unbiased, study.

Jan 1, 1932

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By Secis R

Northparkes Mines is located 27 km northwest of Parkes in central west New South Wales. The E26 deposit is the largest of all defined to-date in the area, containing over 50 per cent of Northparkes' resources and reserves. The combination of orebody geometry and geotechnical characteristics provide ideal conditions for the block cave method of mining of the first lift of the E26 deposit. Although this method of underground mining has been used for decades in other countries, E26 is the first example of its use in Australia. Copper-gold mineralisation at Northparkes is related to quartz monzonite porphyries that have intruded coeval Ordovician volcanics. Sulphide mineralisation (dominantly bornite and chalcopyrite) occurs principally within quartz veins associated with the porphyry intrusions. Veining and mineralisation occurs within both the porphyries and volcanics. To optimise the recovery of a resource within a block cave mine, a good understanding of the rock mass and ore flow characteristics is essential. These have a significant effect on the fragmentation size and range and on parameters such as the drawzone spacing, height of interaction zone and dilution entry. As ore within a cave column moves and mixes when material is extracted from below and beside it, the total reserve extracted is unique for a particular draw strategy/production history. Until recently, reserve estimates and production schedules were based on the application of a uniform dilution factor to the tabulated resource. However, given the complicated flow and mixing within the cave column, such a simplistic approach can produce erroneous results. Northparkes Mines purchased and sponsored the upgrading of a commercially available software package specifically developed for modelling removal of resource blocks under caving conditions. This Gemcom software package, PC-BC, has been used for mine planning, reserve reporting and production scheduling. Blocks within it resource block model are converted into a mineable reserve taking into account mixing and dilution during depletion of drawcolumns (by horizontal and vertical redistribution of insitu tonnage and metal). As PC-BC gives individual drawpoint reserves, it can be used during the planning stage to determine whether or not a drawpoint is economic. For E26 Lift I an optimal layout containing 130 drawpoints has been developed based on a nominal 14 m x 14 m drawpoint spacing and a 0.8 per cent equivalent copper (eCu) cut-off grade. Annual production schedules for the depletion of material above this layout are based on: I higher tonnage removal from higher grade drawpoints in the early years of production; and 2 drawpoint production rates proportional to the total tonnage of orr remaining in the drawcolumn up to the optimal height of draw tier subsequent years. The reserve is tabulated from the combined annual production schedules over the life of the lift. The pre-mining reserve for Lift I of E26 is 26.6 Mt at 1.43 per cent copper and 0.39 g/t gold, of which approximately 23.4 Mt will be extracted under caving conditions. By scaling down the annual production schedule, weekly drawpoint tonnage calls can be given for short-tern production scheduling.

Jan 1, 1997

By F. W. Maclennan

The following is a list of members who died in 1929. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year of Date of Biography Election Name Death 1929 Page 1922 Adams, Waldo Peck................................ June 2 September 435 1903 Argall, Joseph.................................... Nov. 1 1894 Austin, Leonard S................................. Oct. 30 December 580 1905 Bailed, Melbourne.........................Dec. 12 May* 280 1890 Barringer, Daniel M.............................. Nov. 30 February* 119 1895 Batchelleb, HENRr R.............................. Jan. 15 March 167 BINGHAM Charles E............................. 1923 Bibkett, E. H..................................... Apr. 23 August 394 1913 Bibbell, Robert W................................. Jan. 18 April 214 1926 Blackmar, Don C.................................. June 4 March* 189 1920 Bosworth, T. O.................................... Jan. 18 April 214 1894 Boucher, Arthur S..........................Jan. 6 May 257 1927 Brandenthaler, R. R.............................. Dec. 14 January* 64 1889 Bretherton, S. E............................... Oct. 4 December 581 1911 Brunton, F. K................ .. Aug. 17 1924 Brush, Charles F................................. June 15 September 436 1925 Cameron, Frank N........................May 16 July 349 1891 Chambers, Robert E.............................. May July 348 1908 Clark, J. Murray................................. Dec. 3 August* 407 1883 Clymer, edward T............................. Oct. 13 December 579 1914 Cofpey, George T................................. May 8 July 349 1901 Cooke, L. H....................................... Aug. 23 November 537 1915 Cousins, George W........................ June 30 February* 118 1886 Cowles, A. H...................................... Aug. 13 September 436 1892 Crane, Theron I............................. Nov. 2 December 579 1921 Crowell, Samuel B................................ Dec. 9 January* 64 1907 Curtis, Bracey.................................... Jan. 31 April 215 1895 de Batz, Rene........ ............... January March* 189 1928 Dines, Tyson S.................................... March May 257 1909 Dufourco, R. G............................. January November 537 1920 Ericsson, Eric A.................................. Apr. 4 April* 231 1920 Erlenborn, Willi....................... Nov. 10 March* 189 1888 Farish, John B.................................... Nov. 14 December 580 1891 Ferguson, Vincent........................... Mar. 8 May 257 1917 Finucane, T. R.................................... Mar. 22 February* 118 1921 Foch, Ferdinand................................... Mar. 20 1885 Foucar, Edouard I....................... Jan. 3 March 167 1880 Francklyn, Charles G............................. Jan. 11 April 214 1925 Friedl, Arthur J.............................. July 9 September 435 1894 Fuller, James W. Jr............................... April 4 1876 . Goodale, Charles W.............................. April 11 May 258 1912 Graybill, John..........................Dec. 11 June* 320 1887 Gritzner, F. A.................................. Mar. 26 July 394 1906 Gunther, C. Godfrey.............................. Deo. 26 February* 118 1900 Haggen, Edward A.............................. Apr. 22 October 488 1895 Hall, Benjamin M........................Nov. 19 March* 189 1913 Harper, Walter S................................. Feb. 15 August 394 1921 Hawley, William S................................ Apr. 20 June 298 1920 Herd, Walter ... . . . ..... Aug. 23 September 435 1889 Holt, Marmadtjke B............................... Dec. 26 February* 118 1928 Husk, Albert D .... ................June 9 December 580 1920 Hutchinson, S. Pemberton......................... Feb. 16 April 214 1926 Ivanoff, Constantine L............................ Mar. 7 June 298 1914 Jaeger, Frederick..... .............July 28 October 488 1891 Jennings, Robert E.......................Oct. 30 December 580 1922 Johnson, Homar L................................. Sept. 17 October 483 1927 Johnson, Homer H................................. Mar. 21 May 257 1918 Jones, Jesse L ..... ...............Jan. 22 April 214 1892 Jones, Thomas J................................... June 18 October 488 1883 JoOet, Cavalier H................................. Mar. 29 May 258 1881 Kennedy, John S . . . . ... ..........Apr. 22 August 394 1881 Kennedy,- Hugh.................................... May 23 September 435 1895 Kebvin, James H................................... September October 488 1926 Kkom, L. J........................................ Dec. 24 January* 64 1905 La Follette, Harvey M........................... Sept. 19 November 538 1920 MacDonald, Alexander............................ May August 394 1904 Marengo, Paolo................................... May 257 1925 Maxwell, Allison R............................... May 7 November 538

Jan 1, 1930

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Paul N. Freeman

This paper describes the in-situ performance of two IFS powered support installations at Betws and Penallta Collieries in the South Wales Coalfield, United Kingdom. Intensive monitoring of all powered support functions, strata movement, support/strata interaction and coal seam disturbance permitted an extensive evaluation of powered support performance for all periods of the mining cycle. The influence of support design, support rating, face design, proximate strata and scam section upon support and operating performance are discussed. In-situ performance is compared to design specification and to the requirements of Production Instruction 1982/6. Aspects which show significant variation are highlighted. Particular attention is drawn to the precise analysis of support/strata interaction in the form of canopy and base loading profiles. This illustrates the influence of support rating and configuration in determining the interaction of the canopy and base with the proximate strata. Extensometric monitoring of the coalface highlights the potential zones of disturbance within the seam which allied with support position monitoring provides an accurate basis for theoretical considerations of support loading. Conclusions are drawn, the application of which may enhance the performance and operation of IFS supports in thin to medium sections.

Jan 1, 1992

By G. J. Hasenfus

There are no known published methods of estimating the degradation of coal measure rocks by water that are simple and efficient, yet still provide a quantitative, meaningful value for assessing the stability of coal mine floor, roof, and rib. The slake durability test, the standard index method for estimating the durability of rock subject to wetting, can provide misleading results for floor stability assessment. Additionally, slake durability testing is time consuming and requires specialty equipment. Methods based on humidity cycling have been demonstrated to be very effective for assessing coal mine roof, but require specialty equipment and do not address floor stability concerns. Visual observation techniques, such as that developed for the Coal Mine Roof Rating (CMRR) method, adequately qualify rock degradation, but lack quantitative rigor. This paper will describe an alternative method, coined the water sensitivity test, originally developed for floor stability analyses, but also found applicable for roof and rib stability assessment. The test was developed by CONSOL in the early 1990's, and in its current form, has been in use for approximately twelve years. The method is based on the basic slake durability principle of measuring the mass of the rock retained on a screen after submersion in water. The new test employs two screens of different sizes, and also uses modified submersion, drying, and data processing procedures. The method is relatively efficient and can be geared toward batched testing. As with the slake durability test, the resulting index value provides a quantitative measure of the susceptibility of rock to water degradation. In addition to discussing the test method and its development, this paper provides a comparison of results with those fiom standard slake durability tests, and tabulated results for various types of coal measure rocks. Examples of the technique's utility are provided, including assessment of longwall and development floor conditions, roof and rib rock weathering and stability, and drum-bit cutability.

Jan 1, 2005

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By A Jäger, J L. Lett, J Rachocki and B Mobilio

The Newcrest Mining Limited Cadia East Panel Cave mines near Orange, New South Wales, Australia commenced production 1200 m below the surface in May 2014. Understanding the mine-wide impact caving had on excavation stability was a primary objective to ensure a safe working environment as production ramped up in the Panel Cave 1 operation and establishment activities were implemented in Panel Cave 2. The impact of cave interaction between Panel Cave 1 and Panel Cave 2 and establishing monitoring systems to assist mine planning and production as both caves joined is explained in this paper. Monitoring tools such as a microseismic system, open holes, HI-cells, extensometers, fibre optic sensing, cave markers, closure monitoring, underground observations and damage mapping were used to characterise the performance and position of the cave back. The data and observations collected were compared to predictions from numerical and empirical methods and used to calibrate the numerical models for forward prediction and to develop site empirical design tools. The results and methodology for monitoring deep high-output caves are the key discussion points in this paper.CITATION:Lett, J L, Jäger, A, Thornhill, T, Rachocki, J and Mobilio, B, 2016. Geotechnical challenges in cave monitoring – a modern approach, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 203–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By Thorndycraftm R. B.

"PURPOSEThe purpose of this presentation to the Canadian Mineral Processors is to review gold heap leaching systems currently in use and discuss their applicability to Canadian ores. The author's experience with the development and operation of heap leaching spans the past four years at. Pinson, and visits to many ether heap leaches in the western United States.INTRODUCTIONBy way of introduction to the heap leaching system, I will describe in slight detail the method used at Pinson Mining in northern Nevada. This will be followed by a discussion of optional methods in use at other operations visited.The Pinson orebody is a finely disseminated, well-oxidized hydrothermal deposit. Gold particles are finer than 20- microns. The orezone hostrocks are metamorphosed and silici¬fied limestone and shale. Sulfides and carbonaceous materials are negligible.The Pinson open-pit mine has operated since June 1980. It produces 1500 tpd of C.I.P. mill feed averaging .10 oz gold per ton, and 1500 tpd of heap leach material averaging .025 oz gold per ton. Cutoff grades are 0.04 for mill feed, and 0.01 for heap leaching. Stripping ratio is 9 tons of waste and leach grade to 1 ton of mill feed.The project is located in northern Nevada at 4900 feet above sea level.,Winters are fairly severe, with freezing conditions affecting operations from early December through April. Although officially designated as ""high-mountain desert"" country, snow and/or freezing rain occur almost every week of the winter.To date, all Pinson production-scale heap leaching has treated run-90,000 tons of ore are stacked on 300 foot square clay leach pads. Cyanide leach solution is applied through ""wobbler"" sprinklers at .0025 gpm/sq ft for 60 to 90 days. The pregnant solution flows from the heap by gravity to plastic-lined ditches, into a collection sump and then through buried piping to the 2.2 million gallon pregnant solution pond."

Jan 1, 1984

By Servant S

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the scope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the scope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this Mine.

Jan 1, 1998