Search Documents

By Alana Pereira Ramos, Walman Benicio de Castro

Amorphization and martensitic transformation (Ms) characteristics of Ti–Ni-Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the wheel linear velocity from 21 to 63 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate and alloy composition on martensitic transformation behavior is discussed.

Jan 1, 2015

By Cheryl S. Lim

New technologies such as direct reduction and smelting reduction processes are increasingly being used in iron-making and steel-making in addition to conventional blast furnace technology. Critical parameters for control of these processes include the degree of metallization, degree of pre-reduction, and carbon and silica levels. On-line monitoring of these parameters is difficult because measurements often need to be made on hot ores (at or higher than -1000'C) in circumstances where representative sample streams are not readily accessible. A nuclear analyser has been developed which provides continuous, non¬intrusive, real-time measurements of iron, oxygen, carbon and silicon levels in hot ores undergoing reduction. The analyser has been tested in a plant using a direct smelting process on pre-reduced feed to the smelting vessel-, accuracies of 1% relative, 0.5 w'.96 (25% relative) and 1.0 wt.% (9% relative) were obtained for the degree of pre-reduction, carbon and silica respectively. The underlying method, capabilities and potential applications of the analyser will be discussed.

Jan 1, 2001

Accretions of dust on the walls of the offtakes from furnaces and in the waste heat boiler are a cause of significant operating and maintenance problems in non-ferrous smelters. The dust originates from entrained solids in the gas stream and vaporised species that condense during gas cooling. Control of dust formation is very important for minimising the formation of accretions and reducing the severity of environmental problems caused by toxic species, such as those containing arsenic, in the dust. The present paper discusses the formation of accretions and the condensation of dust in copper smelting from a thermodynamic viewpoint. Changes, in gas composition and the amounts and identities of the condensed species in the dust are calculated using computational thermodynamics. Interactions between dust species to form accretions are considered in the light of appropriate phase equilibria. The results show that the nature of the dust formed varies greatly, depending on the temperature and the amount of oxygen present during cooling. Control of the amount of oxygen is required if offtake and waste heat boiler accretion problems are to be minimised.

Jan 1, 2002

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Lead-zinc mineralization is distributed in Egypt along the Red Sea coast between El Qusier and Ras Banas. A representative sample from Um Gheig was collected and ground to -60 mesh for the mineralogical study. It contains hemimorphite (Zn2SiO4.H2O), sphalerite (ZnS), galena (PbS), calcite (CaCO3) and dolomite (CaMg(CO3)2) beside the gangue minerals gypsum (CaSO4.2H2O) and hematite (Fe2O3). Cadmium seems to be incorporated in the crystal structure of the zinc-lead minerals. The chemical analysis of Um-Gheig representative sample revealed that, it contains 16% zinc combined with 0.1% cadmium, 2.3% lead and 0.1% boron beside other elements.Pug and agitation leaching were performed on samples ground to -200 mesh to achieve the maximum dissolution efficiency of cadmium with respect to other elements. Cadmium leaching efficiency reached 90% by using 40% H2SO4 at S/L ratio 1/2 and stirring time 2 hours at 80o C. Cadmium was then separated as yellow precipitate of CdS from the sulfate leach liquor containing 0.9 g/l Cd, 145 g/l Zn, 0.15 g/l B and 0.01 g/l Pb. Separation of cadmium was carried out by direct precipitation using Na2S as well as H2S. The recovery of 94% cadmium free of zinc was achieved.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas. Um-Gheig Pb-Zn ore is a replacement deposit in limestone and calcareous sandstone in the basal series of the Middle Miocene rocks. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, Bishai [1]. As has been mentioned, zinc is a common element and cadmium is comparatively rare in almost zinc minerals. It was estimated that zinc is 200 times as abundant as cadmium. According to Bodas [2] about 2.1% of cadmium was carried by the Zn mineral hemimorphite (15.3% Zn) in Thailand. Also, Onal et al., [3] found that 164 g/t Cd was carried by Pb–Zn ore sample containing 10.17% Pb and 10.98% Zn from Aladag in Turkey. Cadmium metal has gained great importance due to its wide applications in civil and navy purposes as well as in nuclear field. It is characterized by its ability to absorb thermal neutrons during the chain reaction inside the nuclear reactors. It is also used in the manufacture of sheets which directed the chain reactions [4]."

Jan 1, 2008

By Ulrich Kerney

In 1996, bath smelting technology for lead recovery from concentrates and secondary materials was introduced in Nordenham to replace the common sinter plant/shaft furnace operation. Since start-up, a continuous improvement of equipment and operation lead to a steady increase of capacity and plant availability. The decision to skip the reduction stage for slag treatment now allows the treatment of 200000 t/a feed materials with a secondary fraction of up to 70 %. The main feed source for the furnace is automotive battery recycling, which offers oxide paste and metallics to be molten under oxidizing conditions in the lance fired furnace. The lead bullion is transferred to the refinery, where copper, silver and other impurities are removed. Silver is recovered as doré quality. All loopings are recycled to the BSF. Inert feed material is collected in a so-called lead concentrate of metallurgical origin, the primary slag, which is sold. It is rather a valuable feed material for further processing than a slag The off-gas is cooled in a flux-flow system, entering then an electrostatic dust precipitator. Having passed a further washing and cooling system, SO2 is oxidized and collected and sold as concentrated sulphuric acid. The presentation will cover a review of the start-up phase, the development of significant production parameters over the last years and actual production routes and figures. A comparison of environmental data between new and old applied technology is made.

Jan 1, 2006

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

By Claassen J. O.

The Zinc Corporation of South Africa Ltd. (Zincor) operates an integrated roast ? leach ? electrowinning circuit. The efficient removal and control of iron forms an integral part of the process. Zincor developed its own iron removal process (Zincor Process), which was recently shown to be unique with some similarities to the para-goethite iron removal process. Newly developed operating parameters for iron removal are in the process of being implemented. These include a change in the pH-profile and operating temperature, the recycling of seed material and the utilisation of an alternative neutralising agent to aid iron removal. Some of these actions, together with the implementation of a pre-neutralisation step, new filtration equipment and control systems in Zincor?s Residue Treatment Plant have significantly reduced zinc losses associated with iron in calcine and the iron residue produced. This enabled Zincor to take a step closer to world-class zinc recovery levels of around 96% for a similar type of operation.

Jan 1, 2003

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By James R. Craig

Petroleum coke is becoming an increasingly important source of light hydrocarbon products as product crudes become heavier and of poorer quality. The use of petroleum coke to generate synthesis gas results in the formation of residual slags that are enriched in silica, alumina, sulfides, oxides, and free metals. The characterization of these slags and their con? stituent phases is an essential step in considering the ultimate use or disposal of such slags and in understanding how to alter the properties of the slags to optimize the efficiency of gasifiers. Depending upon temperatures and bulk compositions, quenched slags typically consist of silicate glasses, calcium silicates, iron-nickel oxide-sulfide masses, aluminate spinels and free metals. Whereas the glasses contain relatively uniformly dispersed metals and sulfur, the iron-nickel oxide-sulfide masses highly concentrate nickel and sulfur. The aluminate spinels very effectively concentrate vanadium and chromium, thus depleting glasses or other adjacent phases. The abundance as well as the make up of the slags strongly affects the physical behavior of the slags within the gasifiers

Jan 1, 1989

By J. Brent Hiskey, Rebecca Grace Copp

The solvent extraction of yttrium and neodymium from copper pregnant leach solutions (PLS) using Primene JM-T, a primary aliphatic amine, has been studied. Effect of contact time, pH, sulfate concentration, and extractant concentration were investigated using synthetic and actual PLS systems. Standard experimental conditions were 5 minute contact time, pH ~2.5, and 10 % v/v Primene JM-T concentration. Distribution isotherms were constructed for the pure systems and for actual copper leach solutions. Synthetic solutions contained 100 ppm Y and ~75 ppm Nd. Samples of PLS contained 2 - 10 ppm Nd and 14 - 30 ppm Y. Results showed that complete extraction of both yttrium and neodymium occurred within five minutes and at pH values greater than 1. It was also found that sulfate concentration does not inhibit extraction at any concentration. Additionally, the distribution isotherms created show that extraction for these metals can operationally take place in one stage.

Jan 1, 2016

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A three-dimensional (3D) electrode reactor combined with Fenton reagent was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on total organic carbon (TOC) removal rate were investigated, and the results were compared with those of the common three-dimensional electrode reactor. Experimental results showed that TOC removal rate could reach 51.7%, when optimal operating conditions were as follows: initial pH value 3.5, H2O2 dosage 17.6mmol/L, reaction time 90min and FeSO4·7H2O dosage 3.5mmol/L. Analytical results from UV absorption spectra indicated that the organic substances in the coking wastewater were well degraded by this system, which provided good experimental basis for the practical application of this process in the treatment of coking wastewater. This can be meaningful for the treatment of other kinds of wastewater.

Jan 1, 2015

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Kurt Westerlund

Three years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm3/0h at Boliden Rönnskär Sweden on a TBRC smelting galena (PbS). Operating experience from the Kivset flash WHB 11.900 nm3/h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3/h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Shadia J. Ikhmayies

SnO2:F/CdS:In bilayers were produced by the spray pyrolysis technique on glass substrates. The structures were characterized by recording and investigating their transmittance curves, I-V plots, X-ray difractograms (XRD) and by observing their scanning electron microscope (SEM) images. From the I-V plots it was found that the SnO2:F forms an ohmic or quasi-ohmic contact with CdS:In. XRD patterns show the polycrystalline nature of the films and show that there is a small shift in the position of the (200) line of SnO2:F without the appearance of new peaks. The morphology of the structures are compared with those of SnO2:F alone and CdS:In alone on glass substrates.

Jan 1, 2009

By R. Cheng

The kinetics of the solvent extraction of ythium from HCl solution with mono-2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester (HEHEHP) have been studied using a rotating diffusion cell (RDC). The effects of rotation speed, pH, ymium and extractant concentrations and temperature on the rate of extraction were examined. The rate of extraction of ythium appears to be controlled by an interfacial reaction of metal ion and extractant. The concentration of the latter is determined mainly by diffusion through the membrane. The contributions of the rates of diffusion in the diffusion layer, diffusion in the membrane and chemical reaction at the interface to the overall rate have been calculated on the basis of a kinetic model.

Jan 1, 1992

By Ryosuke O. Suzuki

A combined process of electrolysis of CaO in the molten CaCl2 and of calciothermic reduction, so-called OS process, was applied to prepare metallic vanadium directly from V2O3. The fine metallic powder containing 1860 mass ppm oxygen was obtained using 0.5mol%CaO-CaCl2 melt for 10.8 ks at 1173 K. The oxygen level did not decrease further even when twice electricity was applied. Because the metallic vanadium could be electrochemically deoxidized to the level of 10 ppm oxygen from 1.48 %, the large amount of by-product, CaO, due to reduction and the large surface area of the fine particles are the reasons of high oxygen content in the reduced powder.

Jan 1, 2006

By V. A. Luganav

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°c and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 5500C with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilite. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast. In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989