Search Documents

By M. L. Cunha

The lack of control of As and Sb compounds from copper smelters and converters has rendered some chalcopyrite containing arsenopyrite, stibnite and tetrahedrite minerals unusable for metal extraction. In the present investigation, we have studied the carbothennic reduction of Portuguese chalcopyrite mineral concentrate in the presence of lime/CaS04 and CaS04/Si02. Thermodynamic equilibrium calculations were performed to study the distribution of As and Sb between metal and the CaO-Si02-FeO slag phase. The phase equilibrium calculations also show the effect of oxygen partial pressure on the increase in the volume of the slag phase, which helps in lowering the copper metal formation temperature and facilitates a better separation between metal, matte and slag. The reduction reaction kinetics was studied between 850°C and 1100 °C, and the phases formed were identified by X-ray powder diffraction and scanning electron microscopy techniques. The importance of this research for using recycled matte, lean and rich minerals with As and Sb is also explained.

Jan 1, 2001

By M. Hashimoto

The equilibrium distribution ratios of sulfur between molten copper and CaO-fluxes containing caF2 and caC12 were determined in the range of 1300° to 1400° C under carbon monoxide. The rate of approach to equilibrium is rapid and increases with increasing CaCll concentration. In CaO-CaFl-CaCl2 fluxes, the distribution ratio varies in a complex way with temperature and CaFl concentration. The results are compared with those obtained with the binary fluxes of CaO with BaFZ and MgFl ?

Jan 1, 1983

By T. V. Jayaraman, Kranti Kumar, Paul Praveen J., Dibakar Das, A. R. James

"Lead free piezoelectric ceramics with high piezoelectric coefficients are in great demand for sensor and actuator applications. Synthesis and characterization study of one such lead free system, barium zirconate titanate - barium calcium titanate [xBZT-(1-x)BCT] (x = 0.5), via solgel method have been carried out. X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the formation of single phase BZT-BCT nanoparticles (<50 nm). The as-synthesized powders were calcined at 1000°C and the powders were pressed into cylindrical pellets. Solid-state sintering of the green pellets at 1550°C for 2 hrs resulted in single phase perovskite structure. Hysteresis loops were obtained which indicates the ferroelectric nature ofBZT-BCT. The bulk ceramic samples with the highest sintered density (~93%) were subjected to electrical poling and the piezoelectric properties ( d33, kp, & i:,) were measured. The structure and piezoelectric properties were investigated and correlated for the given composition of the BZT-BCT system.IntroductionPiezoelectric ceramics are widely used in various sensors and actuators and most of the piezoelectric ceramics, which are presently used, are lead based, which contains at least 60% lead (Pb) by weight. The critical disadvantage of these lead based piezoelectric ceramics is their hazardous effect related to the toxicity of lead, which poses a serious environmental concern starting from their processing to the disposal stage[l]. It is well known that a material to be a good piezoelectric it requires a morphotropic phase boundary (MPB) i.e. the composition induced phase transition between any two ferroelectric phases."

Jan 1, 2013

By J. Borlée, J. P. Birat

"ULCOS is a large European program launched by a consortium of 48 partners led by arcelor and a core group of steel producers, which was started in 2004 with the support of the European Commission (RFCS and 6FP programs) to search for breakthrough process routes that could, in the future, when fully developed, demonstrate the potential of large cuts in CO2 emissions for the production of steel from iron ore.The timescale for commercial implementation is the post-Kyoto period, i.e. 15 to 20 years from today.The present paper presents the progress made in the first 2 years of this 5 year program.Several concepts are being investigated in parallel: re-engineering of the blast furnace to incorporate CCS in the core of the process, smelting reduction with CCS capabilities, massive use of natural with more CO2-lean technologies than today, hydrogen steelmaking and electrolysis of iron ore. Biomass also offers very attractive perspectives, while raising major challenges.None of these new steelmaking routes are ""no regret"", which means that the European Steel Industry has already incorporated extensive energy saving steps in its present process technology and is working as close to thermodynamics limits as is cinematically and economically feasible, and that decreasing GHG emissions further means introducing breakthrough technologies that add significant costs to the operation of the Steel Mills.They will also require much research and development before they can be proven and implemented commercially.IntroductionThe ULCOS program (Ultra Low CO2 Steelmaking) is a large research program of the European Steel Industry and its industrial and research partners launched in September 2004 to investigate steelmaking technologies that have the potential of reducing the CO2 emission of the Industry by a large amount, typically in the order of 50%. It is supported in the European Community by the 6th Framework and the RFCS programs through 3 complementary European projects [1,2].The present paper summarizes the work carried out in the phase 1 of ULCOS and in framing the program of phase 2."

Jan 1, 2008

By Boris Arlyuk

The system of short term forecast of metal prices at LME is based on correlation between prices within the quarter forward and at the first place by economic parameters at the West, determining the consumption of metals. Such economic parameters are presented by data of indexes of Western World industrial production (WW IP), official data of IP and Dow Jones indexes at USA. For price forecast within the quarter forward (one day ahead, 3 day -65 days MA forward prices) are significant the changes of actual prices (official and close) at the past and the parameters of daily trade at LME at the past (futures turnover, open interest, LME stocks). It is developed subsystem of price forecast within the quarter forward based on analytical approach determining the relations between the participants of the market. It gives the opportunity to reduce the number of empirical coefficients at the model and receive good accuracy of forecast the MA prices and its direction at the future. Very important part of short term forecast is subsystem determining analytically the probability that the price forecasted for the next trading day will be the maximum or minimum daily price within the quarter forward. The thresholds probabilities are defined by identification the model at the past by maximal commercial efficiency. Such system was tested at the past at period since 2000 till 2005 and gives very high commercial results at operations on 1M forwards and hedging the sales of nonferrous metals traded at LME (primary aluminium, light alloys, nickel, copper, zinc, lead and tin).

Jan 1, 2006

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By Fuqiang Zheng, Shuai Wang, Ting Duan, Yufeng Guo, Tao Jiang, Andrew Yakovlevich Travyanov

Organic compound binder can effectively enhance the strength of green pellet and reduce the addition amount of binder during pelletizing. However, compared with traditional bentonite binder pellet, the compressive strength of the preheated and roasted pellets significantly declined. It is of significance to resolve this problem for the application of organic compound binder. In this paper, magnetite concentrate was used as raw material, carboxymethyl cellulose (CMC)- bentonite compound was used as binder, characteristics of preheated and roasted pellets and the effects of additives on that were systematically studied, The results show that sodium acetate can effectively improve the characteristics of the finished compound binder pellets. The compressive strength of the preheated and roasted pellets were increased by 52/N·p-1 and 342/N·p-1 respectively when the addition amount of sodium acetate is 2.2%wt of compound binder. Moreover, sodium acetate has no adverse effect on pelletizing process and drying characteristics of green balls.

Jan 1, 2015

By M. F. Hochella

Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) analysis have been used to study the mode of occurrence and mineral associations of gold in partially oxidized high grade gold ore from the Carlin sediment-hosted deposit. Rounded.gold particles have been observed that range in size from 0.03 to 0.1 p.m (300 to 1000 A) in diameter. The gold is associated with maghemite h-Fep3l and a K-Al-Si-bearing phase that is suspected to be illite. Detailed descriptions of gold and its mineral associations in &apos;Carlin-type&apos; gold deposits are critical not only to understanding the mechanism of fluid transport and precipitation of gold, but also to developing improved metallurgical techniques for the recovery of gold from refractory ore. Direct observation of gold in unoxidized ore is rare due to its relatively high degree of dissemination and low average bulk concentration which averages 9 ppm according to Radtke (1). Hausen and Kerr (2) observed 1 to 5 p.m grains of gold directly in oxidized ore but these microscopically visible particles account for only a small percentage of gold present in the ore. The samples used in this study were selected from individual beds of high grade, partially oxidized ore (4.55 oz/ton or 156 ppm gold) that were collected in the Main pit of the Carlin mine. The samples were collected from several thinly laminated carbonate micrite beds within the top 50 meters of the Roberts Mountains Formation. The carbonate micrite has been altered by hydrothermal fluids to a calcite-absent, moderately silicified rock referred to as alteration zone #3 by Bakken and Einaudi (3). Based on petrographic and SEM studies, the samples contain carbonaceous matter, and both pyrite and iron oxide pseudomorphs after pyrite. The oxidation of pyrite may be a pro-duct of deep weathering, in which case limited remobilization of gold may have occurred. TEM sections of the rock were prepared by first embedding small chips in low viscosity epoxy. The epoxy blocks were cut with a Reichert Ultracut E ultramicrotome, producing thin sections less than 0.1 p.m thick. The sections were examined with a Phil-lips 400ST TEM at 120 keV in both imaging and selected area diffraction modes. Native golci*was easily detected in TEM bright field images due to the large electron density contrast between gold and all other phases that are present (Figs. 1 and 2), Gold was positively identified with high spatial resolution EDX analysis in the transmission electron microscope, although selected area diffraction of individual grains was not successful EDX analyses of the platy and massive minerals immediately surrounding the gold particles typically indicate the presence of Si, AI, K, and Fe, However, the d-spacings derived from selected area diffraction of these polycrystalline masses (as, for example, in Fig. 2) give an exact match for maghemite. As a result, there is no diffraction information to identify the K-AI-Si-bearing phase(s). The lack of a diffraction pattern could be due to either electron beam damage or to a poorly crystalline phase(s).

Jan 1, 1987

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001

By Nolberto Moreno Borjas

This paper outlines the detrimental impact that unblended ore can have on the Ni and Co recoveries and the ore slurry density with real data from the Caron low-pressure ammonia leaching process for the Punta Gorda ore. The author briefly discusses the reason for the decrease in slurry density that the process experiences. The lower metal recoveries in the process that are caused by the unblended ore chemical characteristics and variations are shown with a data base statistical analysis drawn from the results obtained from a pilot test, designed with different ore bypassed from the normal process flow and a similar ore from a similar metallurgical treatment. Keywords: Ni-Co Laterite, Caron Process, Ore Blending, Slurry Density, Metal Recovery

Jan 1, 2004

By Juan Patricio Ibáñez

Separation of arsenic and copper from Cu-As-H2S04 electrolytes by electrodialysis has been investigated at room temperature. The effects of current density and pH were studied. An arsenic-free copper solution was obtained for all the tested conditions. The transport efficiency for copper ions was found to be higher than 98% after 3 hours&apos; test. Transport of arsenic and copper through the ion exchange membranes was increased by increasing pH and current density. Solution pH was found to be a key parameter for the separation process, since it controls the speciation of the ions to be transported and the formation of unwanted precipitates which reduce the global efficiency of the electrodialysis process. The main conclusion is that electrodialysis is a promising technique to be used in separating and/or concentrating ions of interest in copper electrometallurgy.

Jan 1, 2003

By Run-bo Wang, Zhe Wang, Fan-yi Meng, Jian-Liang Zhang

The influence of semicharcoal substitution for coke breeze on sintering performance was investigated by pot-grate sintering test. At a fixed fuel ratio, sinter productivity and strength decreased with the substitution increasing from 0 to 100% due to better combustibility. To enhance the utilization efficiency of 100% semicharcoal, sintering parameters (moisture and suction pressure) was adjusted. With the moisture increasing, sinter performance of 100% semicharcoal increased because of the suppression of semicharcoal incomplete combustion. As the moisture further increasing to 9.0%, sinter quality gave rise to a decrease trend. The results also showed that the increase of suction pressure was benefit for the increase of heat transfer rate, leading to the improvement of heat utilization energy. Measures to enhance magnetite oxidation during sintering are discussed based on current understanding of the fundamentals that control the sintering process.

Jan 1, 2015

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30tlhour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By E. M. Weenink

A proposed alternative to the conventional zinc extraction processes is the flash reduction of zinc calcines. As part of an overall study of this process, the kinetics of single zinc oxide pellets were investigated. Pellets, compacted from Outokumpu zinc calcine (60.9% zinc, 9.6% iron), were suspended in a flow of CO/CO, mixtures and reduced at temperatures between 1000 and 1200°C and atmospheric pressure. The pellet weight loss with time was recorded and analyzed. It was found that the reduction of calcine pellets (0.9 cm height and 1.36 cm diameter) was controlled by chemical reaction. This paper includes an analysis of the experimental results of two previous investigations of ZnO reduction.

Jan 1, 1992

By Takashi Ikeda, Masafumi Maeda

"Demand for solar cells is increasing linearly throughout the world. Last year production totaled 3000 tons worldwide. The market size of solar silicon is expected to increase further because of international ""political"" demand to reduce carbonaceous emission from energy consumed. Most elemental silicon is produced by the carbon reduction of Silica in an electric arc furnace. Purity of silicon at this stage is 90-99%. Major impurities are Fe, Ti, Ca· and Al, and minor ones are P, B and carbon. The oxidizing metallurgical process is no longer effective to remove transitfon metals because those are less noble to silicon. Nonmetallic impurities such as phosphorus and boron must be reduced to 0.001ppm for semiconductor use. The most common process for high purity silicon is the Siemens C process, which is basically distillation of hydro-chlorinated silicon followed by CVD of SiHCl3. The cost of such silicon is expensive to allow its popular use in solar cells. Currently scrap silicon -of semiconductors is used for this; however, the supply-of that scrap is limited to just a portion of semiconductor production.In this paper world demand for silicon will be reviewed and some of the processes proposed summarized.IntroductionSilicon is element 14 in atomic number and has an atomic weight of 28.0855. Little elemental silicon is found in the earth, and it is mostly found as oxides or silicate. The Clark number of silicon is very large and the second in its number. If we were discussing the volatility of silicon element on the globe, we would never worry about it. However, it is very difficult to obtain pure elemental silicon because a high purity silicon compound is very rare. In most cases these are silica (silicon oxide SiO2). As shown in Table 1, there are many grades of silica ore classified mainly by their content of iron and alumina."

Jan 1, 2000