Search Documents

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By E. Bauer

During 1987 and 1988, the Eighty Four Complex Mine of BethEnergy Mines, Inc. used the open entry longwall recovery method to recover one partial and three complete longwall faces. Various cement- concrete supports were utilized to support the open recovery entry until the approaching longwall face cut into this entry. This recovery method and the supports used were studied by the mine personnel and the Bureau of Mines. This paper discusses the findings, results and conclusions of that study.

Jan 1, 1988

By S. I. Al-Ameen

Monolithic packing systems have gained in popularity as a gate side packing method, However, there has been no detailed investigation to assess their underground strength behaviour. This work includes the laboratory and in situ investigation for strength behaviour determined on various monolithic packing materials namely Tekpak-XX, Hydropak-20, Hydropak-30, Astrapak-3R, Flashpak, Thyssen pack and Aquablends. A simple technique for assessing the pack strength was developed at the laboratory by using a penetrometer, of which penetration resistance can be directly correlated with the uniaxial strength of the pack. The in situ strength investigations were made on core samples obtained from three pipes inserted inside the pack, while the penetration test were made on the pack surface. The in situ results indicated that the packing material develops an inconsistent strength on various part of the pack which was mainly related to an inadequate mixing of grouts inside the pack.

Jan 1, 1992

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

By Gustavo Herrera Rico

As part of a general effort to increase safety, efficiency, and profitability of its mining operations, MICARE personnel with the support of NorWest Mine Services, Inc. determined that the key to improving development mining was the implementation of roof bolting as the means of primary roof support for both main entry and longwall gate road development. Until mid-1994, MICARE had relied exclusively upon primary roof support systems composed of heavy steel beams and wooden posts. Support systems were designed, implemented, and evaluated that were successful in controlling the mine roof under extreme geological conditions. This paper describes the geological challenges, support selection criteria, and presents the instrumentation and 'mine measurements made to assess the bolting performance during the development and retreat mining process of longwall mining.

Jan 1, 1997

By Yi Luo

The responses of a section of railroad to ground subsidence process was monitored as it was undermined by a longwall panel. The subsidence data collected and the observations made through this monitoring program could help us understand betteer the ground subsidence process and its impact on linear structures such as railroads. The data analysis techniques used and the assessment methods presented could be useful to researchers practitioners in the field of mining subsidence.

Jan 1, 1994

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

By S. K. Sharma

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae, Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar strength.

Jan 1, 1992

By Wilfried Ufer

[1. Einführung in die Problematik 1.1 Die Bedeutung des Schildausbaus Seit fast 30 Jahren ist die Konkurrenzsituation auf dem Primärenergiemarkt der Bundesrepublik Deutschland durch einen von Erdöl and Erdgas geführten and insbesondere gegen die Steinkohle gerichteten Verdrängungswettbewerb gekennzeichnet, der den Steinkohlenbergbau zu tiefgreifenden RationalisierungsmaBnahmen zwang. In diesem Zusammenhang kam es Anfang der 70er Jahre zur Einrührung des Schildausbaus, der eine erhebliche Produktivitätssteigerung in den Strebbetrieben zur Folge hatte and damit die Uberlebenschance des Steinkohlenbergbaus in der Bundesrepublik Deutschland enorm verbesserte. Der Grund hierfdr lag darin, daB der Schildausbau im Vergleich zu dem vor ihm eingesetzten Rahmen- and Einzelstempelausbau eine wesentlich hdöhere Ausbauleistung erbrachte, weil er sich weit weniger empfindlich gegen Hangendausbruche and aus dem Alten Mann hereinbdschende Bruchberge erwies. So erklärt sich auch die stürmische Entwicklung and die schnelle Verbreitung des Schildausbaus. Bereits 1975 stammte rd. 50 % der Fdrderung aus Schildstreben, 1990 waren es fiber 75 % and heute sind es fiber 90 %. 1.2 Die Staubentstehung beim Schildausbau Die Erfolge des Schildausbaus sind unbestritten. Jedoch nahmen :nit seiner Einführung die Probleme der Staubentstehung and Staubbekämpfung im Vergleich zum Ein zelstempel- and Rahmenausbau erheblich zu. MaBgebend dafür sind hauptsächlich folgende Gründe: - Abbau von dozen nit gebrächen, weichen Hangendschichten, die erst durch Schildausbau abbaubar wurden, - Zerkleinerung des auf den breiten Kappen aufliegenden Bergematerials infolge der höheren Ausbaustiltzkrafte des Schildausbaus, Zermahlen der sick in die Spaltabdichtungen hineinarbeitenden Bergestückchen, - Erhöhung der Wettergeschwindigkeit infolge der durch die Baufarm des Schildausbaus bedingter. Verkleinerung des Strebquerschnitts verbunden mit der Aufwirbelung and Aussichtung von Staub, - Aufwirbelung von bereits abgelagertem Staub im Bruchraum beim Hereinbrechen der Dachschichten. Die genannten Gründe treten zumeist nicht in jedem Abbaubetrieb gleichzeitig auf. Sie rind vielmehr u.a. abhängig vom Ausbautyp, von den Gebirgsverhältnissen and von der Abbaugeschwindigkeit. Trotzdem ergeben sich beim Vorrücken des Ausbaus in der Regel hohe Staubkonzentrationen, die deswegen besonders kritisch sind, weil es sich um quarzhaltigen Feinstaub handelt, der besonders gesundheitsschädlich ist. Die Hauptzutrittsstelien]

Jan 1, 1984

By Leslie Carver

The effects of longwall mine subsidence on water resources were studied at a West Virginia coal mine (mine Z) by Carver (1994). Data were obtained for 137 domestic supply wells and springs and 12 baseflow streams. Subsidence caused short-term dewatering (of a few days to weeks) of wells located on lower hillslopes and valleys, and long-term dewatering of hillslope and hilltop springs (with no recovery yet). New or increased spring discharge was observed at lower elevations. Unsubsided water supplies experienced no dewatering beyond a nearby panel's 27°-38° angle of dewatering influence zone. Subsidence from longwall mining beneath streams commonly reduced discharge when panel ages were less than two to three years. However, "normal" discharge was typically observed over panels greater than three years in age; such streams exhibited lower baseflow recession constants, moderated winter baseflow, and increased summer baseflow compared to unsubsided streams.

Jan 1, 1994

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By J. Nielen van der Merwe

The main objective of the research described in the paper was to determine the causes of falls of roof in South African coal mines. The south African Colliery Manager's Association and the members of the South African National Institute of Rock Engineering (SANIRE) who are employed by coal mines lent full support to the work. Fifteen major roof falls were investigated in detail and their causes established. This data was supplemented by mapping a large number of roof falls on four coal mines in less detail. The total number of recorded roof falls was 182. The data bank simulated the data bank of roof falls that resulted in fatalities in terms of the total number of falls recorded and the thickness distribution of the collapses. It was found that the causes of the falls differed for different thickness ranges of roof falls, The thin falls, classified as "Skin falls", which accounted for approximately 70% of all fatalities, were predominantly caused by ineffective joint support and excessive bolt spacing. Ineffective joint support was found to be a dominant cause of roof falls for all thickness ranges, while the influence of excessive bolt spacing diminished with increasing fall thickness. However, it remained a significant cause of roof falls even for the major falls. Burnt coal, dykes, bad mining practice, weathering and inferior materials were found to be minor causes, but nonetheless contributed to the falls. Horizontal stress was a minor cause, with increasing contribution for thicker falls. It was also found that the indicators of horizontal stress coincided with areas of reduced roof rock strength. In general, roof falls occurred in areas where the roof rock was found to be less competent in terms of rock mass rating systems. It was concluded that the Coal Mine Roof Rating (CMRR) system developed by NIOSH in the USA held promise for application in South Africa and should be investigated further.

Jan 1, 2001

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By John W. Fredland

Conducting mining operations under a body of Water can create hazardous conditions for miners. The potential for a sudden inrush must be considered and abnormal ground control conditions can be encountered. This paper synopsizes the factors which mine operators should take into account when evaluating whether an inrush may occur. It addresses the applicable Federal regulations and discusses some items which coal operators should consider in applying for a permit, Through collecting and analyzing the pertinent information, the likelihood of encountering problems can be judged. Through proper mine planning, the potential for creating hazardous conditions can be mitigated.

Jan 1, 1982

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003