Search Documents

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Leigh Sharpe

Dunng the last 5 years a United Kingdom colliery has utilised a yielding-pillar configuration to extract a relatively thick coal seam at a depth of 640 m. As part of ongoing research into the siting of roadways adjacent to extracted longwall panels, seved field monitoring sites were established at differing locations to investigate roadway stability and yielding-pillar performance. Characteristic roadway deformation has been identified together with strata softening pathways which indicate the temporal increase in the height of softening into the roadway roof. In the assessment of such a complex problem numerical modelling, using FLAC, has been shown to contribute vital additional information, and provide further insights into the mechanisms controlling strata behaviour.

Jan 1, 1998

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Andre Cezar Zingano

"The empirical approach for pillar design assumes that geological conditions should be perfect, such as horizontal seams, and that pillar strength and behavior will only depend on the coal seam strength and the vertical pressure caused by the overburden thickness on the coal seam; this vertical pressure is based on the tributary area. Empirical methods do not consider the effect of the interface between the roof and pillar or the floor and pillar.The effect of the interface shear strength on final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 meters). This case study involves a mining section at the 101 coal mine in the Santa Catarina state of Brazil, which is experiencing pillar rib spalling and yielding because of a 1-to 2-cm-thick clay layer at the area of contact between the coal seam and immediate roof. The depth of the coal seam is 60 m on average and 2.3 m in height. This particular section also has 12-14% (7-8°) of seam inclination. The pillar size varies from l lxll to 13xl2m; thus, the safety factor (SF) based on the ARMPS approach is more than 1.5. The objective of this paper is to determine the cause of the pillar yielding and study the effect of the clay layer at the interface between the roof and pillar, including the inclination of the coal seam. This study conducted empirical and numerical models (2D and 3D) to understand the effect of the thin clay layer. The conclusion is that the clay layer affected the strength of the interface between roof and pillar, causing rib spalling and reducing the pillar strength.INTRODUCTIONPillar stability and deformation depends on the coal seam strength and vertical pressure caused by the overburden thickness on the coal seam, and this vertical pressure is based on the tributary area. The effect of the interface shear strength on the final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 m). This interface could be represented by a thin clay layer or an abrupt contact between the coal seam and a rigid sandstone layer of the immediate roof. These two interface conditions are found in the coal mines of Brazil, and the effect of the interface shear strength could increase when the seam's inclination is higher."

Jan 1, 2016

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By Selmar A. Oliveira

"Safe mine closure is an important step in the mining lifecycle. Plans for safe and efficient closure should begin at the inception of mining. Ideally, closure occurs when the reserve has been depleted. However, when the abandonment of a mine occurs prior to the depletion of the reserve, several problems arise which need to be treated. This situation occurred at Verdinho Mine, located in the state of Santa Catarina, southern Brazil. Verdinho Mine is a coal mine that operated for more than 40 years without had backfill technologies applied. Soon before the exhaustion of the reserves, it was abandoned by the owners without proper closure. As a result, the Federal Public Ministry filed a public civil action to promote proper closure. Several parties are currently involved, including the National Department of Mineral Production (DNPM), the mining regulator of the Brazilian Government. To meet the judicial determination, a cooperation agreement was initiated between DNPM and the Federal University of Rio Grande do Sul (UFRGS) to identify and to monitor parameters which could result hazard due flooding mine, to model the various conditions to minimize the impact of flooding caused by total abandonment. Many processes must be planned and planned early in mining operations, and these processes must be performed over the life of the mine. Financial resources must be guaranteed by a specific fund fueled by operating revenues. When these resources are not properly employed, costs and technical difficulties prevent proper closure progress. If the removal of subsoil equipment, treatment and control of groundwater, regeneration of the surface, and closure of openings are not done correctly, there can be environmental, social, and stability impacts over time. To avoid this in the future, a detailed study is being performed at the Verdinho Underground Coal Mine on how to appropriately implement mine closure and monitoring procedures. This study is being conducted in response to a lawsuit filed by the Federal Public Prosecutor’s Office. INTRODUCTION The nature of the Mining Industry is such that all mining is a temporary activity, where the operational life of a mine is defined by the final project scope. The operating life of a mine lasts from a few years to several decades. Mine closures occur once the mineral resource at a working mine is exhausted, or operations are no longer profitable. Mine closure plans are required by most regulatory agencies worldwide, such as the Mineral Production National Department (DNPM) in Brazil."

Jan 1, 2017

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015