Search Documents

By D. PATIL, B. K. Parekh

Water is the mainstay for the beneficiation of fine-size coal and minerals, but it is also the least desirable constituent of the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of the individual particles. When a differentially heated solid mixture is placed on a moving belt that has been coated with low-temperature melting resin, the hotter component of the mixture will stick to the belt while the relatively cooler component will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz particles of 6 × 18 mesh size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary test results show that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By H. E. Rutherford

Monterey Coal Company has begun a geologic monitoring program in order to better understand our in-mine geologic conditions and to apply the knowledge gained to our mining operations. Two methods are used to collect information. The first is a monthly examination of conditions throughout the mine using a rapid mapping technique. The second is the detailed mapping of specific events encountered during mining such as faults and roof falls. The data gathered from both methods is correlated with operational statistics to create a geologic/production database. From the database, a monthly evaluation of mining conditions is made. Also, the database has proved useful in such areas as forecasting roof conditions and examining how faulting has affected mining operations.

Jan 1, 1984

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By John C. Cook

There is pressing need for better means of exploring ground conditions ahead of mining. Exploration drilling has the drawbacks of high cost and a seriously restricted sampling zone. Traditional geophysical exploration methods including gravity, magnetic and resistivity techniques have been used with some success underground, but all give poor target delineation relative to range, since they depend upon minor distortions of a potential force field. Much greater ratios of resolution to range can, in principle, be obtained by employing electromagnetic or seismic radiation as the exploring agent. This is because propagation time delays can be used to measure range accurately, and to separate the small effect of a distant target from the much larger effects of nearer targets and of the transmitter. Seismic waves have long been used with great success in exploration for petroleum, and recent research on their application underground is promising. Electromagnetic (radar) waves have been very successfully used for detection and location through the air and outer space, and have also explored through polar icecaps more than a mile thick.l It is not generally realized that below the soil many rocks are also somewhat radar-transparent, and that radar can be used for exploring such rocks, once a quarry, a mine, a borehole, or other means of access has been opened. Radar waves are reflected by any boundary or object where they encounter a large change in electrical properties.2 The usual cause of such a change is a difference in moisture content. Radar waves passing

Jan 1, 1972

By H. P. Rosenof

The G2 real-time expert system, a commercial product since 1988, is widely deployed in process, manufacturing and other industries. A number of innovative applications are installed or under development in the mining and metallurgical industries. These include: ? A chemical reagent control system for a mineral concentrator, at a mining company; ? A supervisory control system for a product dryer, at a surface coal mine ? A training system for equipment operators, at a steel mill; ? A scheduling system for furnaces at a hot rolling mill; ? A simulation system for mining operations; ? Several graduate-level research projects in materials handling at a university Realized and projected benefits will be discussed. In addition certain applications installed or under development in other industries will be proposed as applicable in mining and metallurgy. For example, applications for the management of vehicular traffic may find use in mining and shipping.

Jan 1, 1992

By Y. Q. Lu

Efficient flotation of fine phosphate minerals from a deslimed waste phosphate stream (-74 microns) has been achieved by both bench-scale flotation and by flotation with a 2-inch air-sparged hydrocyclone (ASH) unit. A sample was collected from the waste phosphate slime stream at the SF Phosphate Limited Operations near Vernal, Utah, for flotation experiments at University of Utah laboratories. The collector used was a mixture of fatty acid, petroleum sulfonate and kerosene. Bench-scale flotation test results show that the minus 15-micron particles have a significant adverse effect on phosphate flotation. When the minus 15-micron material was removed by a classifying hydrocyclone, improved flotation recovery and concentrate grade were realized. A bench-scale flotation recovery of 86 % with a concentrate grade of 16% P2O5 was obtained from classified waste slime (74 x 15 microns) feed material containing 11.3% P2O5 In contrast, a 90% P2O5 recovery was achieved with a concentrate grade of 16-18% P2O5 by single-stage ASH flotation. With a second stage of ASH flotation, a concentrate containing 23% P2O5 was realized at an overall recovery of 75%. These results indicate that the industrial application of ASH flotation technology for phosphate recovery from waste slimes is promising.

Jan 1, 1995

By William W. Edgerton

Establishing geotechnical baselines on soft ground projects that require the use of closed-face tunnel boring machines (TBMs) is difficult. It is hard to see the face when mining and the excavated material is combined and mixed, all of which makes baseline quantifications challenging. In an attempt to meet underlying objectives of minimizing bidder contingencies, allocating or sharing risks and paying for conditions only if they occur, nongeotechnical baselines (i.e., functional baselines) have been developed. These have been used on the District of Columbia Water and Sewer Authority?s Clean Rivers (DCCR) Blue Plains Tunnel (BPT) project. This article examines the development of such functional baselines and how they were implemented on the BPT project.

Jan 1, 2012

By A. J. Sinclair

One hundred and eleven pyrite samples from 3 porphyry-type deposits in the Canadian cordillera were analyzed (many in duplicate) by AA spectrophotometry for Co, Ni, Cu, Pb, Zn and Mn. All elements have density distributions that are lognormal or combinations of lognormal populations. Co and Ni in pyrites show zonal patterns that relate generally to mineralogical zones in the porphyry systems, particularly if contoured as the Co/Ni ratio. High Cu values in pyrites also correlate with Cu-rich mineralogical zones. Other elements studied appear less regular in their distribution patterns, although Zn highs in pyrite seem to occur sporadically near the margins of porphyry systems. In particular cases, pyrite geochemistry shows potential as an exploration tool to aid in target definition for detailed exploration.

Jan 1, 1976

By D J. Bradshaw

It is well known that the chemical environment determines the success of the flotation process, however its characterization and control is difficult to achieve. This work evaluates the use of various measurements, including mineral potential measurements, in gaining an understanding of the influence of varying parameters such as the milling media and the reagent suite composition on the flotation performance of a platinum group metal (PGM) bearing ore. The results showed differences in the response of the various mineral electrodes to the different conditions, however the changes in flotation performance of the different minerals in the ore could not be wholly described by the electrochemical changes, demonstrating the limitations of these measurements.

Jan 1, 1999

By W. M. Hart

The current Automatic Data Acquisition system developed by some support manufacturers makes it possible to continuously monitor and record changes in leg pressure and advancing ram stroke in every shield, and shearer position at any moment during the mining operation. In order to effectively use the massive data obtained from this system for improving production and maintenance managements as well as providing better roof control at a longwall face, the research currently conducted jointly by West Virginia University and Cyprus-Amax Coal Co. attempts to develop a Longwall Management System for mine operators. The LMS software package runs on a MS Windows NT environment and consists of four sub-systems: (1) Data Interpretation and Analysis; (2) Production Management; (3) Maintenance Management; and (4) Ground Control. This paper presents the details of each sub-system.

Jan 1, 1995

By M. Misra

The dissolution of mercury during gold cyanidation is the cause of many environmental, health and processing problems. A study was undertaken to find a suitable reagent for the removal of mercury bearing complexes from the leach liquor. Removal of mercury from synthetic solutions and process water from a gold mine was investigated using sodium sulfide, sodium and potassium dimethyl dithiocarbamates as precipitating reagents. The results have shown that efficient mercury removal could be achieved by addition of potassium dimethyl dithiocarbamate (KDTC), by formation of stable mercury compounds. The resultant mercury-potassium dimethyl dithiocarbamate precipitates are stable under present plant operating conditions and do not have any deleterious effect on gold adsorption by activated carbon. Furthermore, it is also possible to stabilize the mercury in the heap during cyanidation by adding dimethyl dithiocarbomate.

Jan 1, 1998