Search Documents

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By Eric Lundgren

The mining paradigm is changing on the continent of Africa. Jessica Kogel?s closing statement from her September 2013 President?s Page (ME, September 2013, pp. 6) has never been more appropriate, ?Africa is shaping up to be the next mining powerhouse, and there is huge opportunity for local communities, national governments and private industry to work together to create a win-win situation for all.? Supporting this notion, attendance at numerous industry conferences around the world demonstrates the shift toward a more sustainable, more environmentally conscious extractive model. But questions remain: How effectively is the industry making this transition, and how willing are companies to learn from the experiences of others? The international development community, as we like to call ourselves, is going through a parallel shift. We are experiencing our own funding crisis; governments are not as flush with resources as they were pre-economic meltdown. But more importantly, after a half century of implementing development programs, we must admit that while some of our programs have been fantastically successful, too many still fail to achieve the goal of poverty alleviation for the world?s poorest. Moving forward, we are forced to recognize that achieving success in scale and sustainability is not always accomplished from our work alone. As the director of international programs for Africare, a nonprofit with more than 40 years of experience implementing community-based development programs in Africa, I can report that our organization is changing the way we think about successful development partnerships. Africare recognizes that for too long the mining sector and nonprofits have been at odds, choosing noncommunication as a ?solution? to the problem. Both sides now recognize that this standoff is outdated, and Africare, specifically, is ready to cross the proverbial line. We see the potential benefits of mining for local communities and, when done responsibly, the opportunity to properly manage Africa?s resource boom as a benefit to all. There are challenges in this conversation. Many mining professionals view nonprofits as whistle-blowers, ready in a pinch to speak to news sources and complain about poor operational standards. Those are advocacy organizations, and while their role is important, they are not the only nonprofits interested in mining operations in developing countries. Organizations like Africare, with decades of experience implementing poverty reduction programs, approach this differently. We know we can work with mining companies to promote economic opportunity in the communities where mining operations are occurring. We recognize that the conversation is difficult, and we are open to discussions about how we can bring our unique experience to bear on the problems faced by mining companies in carrying out their investment programs.

Jan 1, 2014

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By P. Davis

With new mineral deposits found in areas of difficult terrain, and annual production capacity increasing in mines over the last decade, the aerial ropeway is proving to be a viable, economic method of transportation from mine to processing plant. Of the more conventional designs, a bicable ropeway is more suited to difficult country than the simpler monocable. The bicable, however, does have limitations in the difference in levels it can accommodate in one section at a given capacity. This is noticeable where hilly terrain and high capacity imposes a limit on the length of each section. Increasing the number of sections for a relatively short conveying distance tends, in the case of conventional bicable, to unbalance the normally favorable economics of the ropeway. In addition to analyzing hauling rope stresses, other areas have to be considered when looking at high capacity ropeways. Bucket capacity, speed, and the wheel load on track ropes are examples. These and other factors led British Ropeway Engineering Co., of Sevenoaks, Kent, UK, to produce the twin-track system. Using twin track ropes, larger capacity buckets, and, if the height differential warrants, the installation of twin hauling ropes, BRECO produced a ropeway design for areas of hilly terrain and at higher capacities than had been considered suitable for aerial ropeways. Designs have been produced for systems handling 1.5 kt/h (1,650 stph), and the potential exists for expansion to above 2 kt/h (2,200 stph). The arrangement of ropes provides high stability of the cars and is especially suited to areas where high winds occur during normal operation. This development allows the aerial ropeway to be applied economically in difficult areas and at the increasingly high capacities demanded by engineers. Ropeway Transports Limestone to Sudan Cement Plant Maspio Cement Corp. of Atbara, Sudan, will soon use an aerial ropeway to deliver its entire limestone requirement 20 km (12 miles) from quarry to plant. The Atbara plant is located north of Khartoum, near the east bank of the Nile River. The quarry is west of the river, in hills rising from flat desert country. The original transport system was a 24-km (15-mile) railway from the quarry to the west bank and a monocable ropeway that crossed the Nile and continued to the fac¬tory, a distance of about 2.5 km (1.5 miles). This original ropeway had a capacity of 60 t/h (66 stph). With the extension of cement-making capacity in the late 1970s, 2.5 kt/d (2,755 stpd) of limestone was required and a new mono-

Jan 3, 1984

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By J. R. Dyni

Colorado nahcolite deposits, estimated at 29 billion metric tons, formed in an asp metric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCOg) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62 percent), disseminated crystals (24 percent), and impure beds (14 percent). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1980

By Arnold P. Szaj

There is no startling revelation to the fact that the mining industry as a whole is generally moving toward the use of larger equipment to process ores in quantities far greater than what was even considered a decade ago. Trucks and shovels have led the way in extra large machines and many other manufacturers have followed suit in the development of so-called "supers" in their line of equipment. In order to keep pace with the industry, crusher manufacturers have also enlarged the size of their equipment. There is now on the market, a Gyratory crusher capable of accepting a 72" diameter piece of ore. Primary jaw crushers have also increased in size. It is inevitable, therefore, that larger secondary cone crushers would also be required to complement the other equipment used to process these large quantities of ore. This super-size secondary cone crusher is the SYMONS 10 Ft. Cone Crusher. Until 1973, the largest cone crusher built was the 7 Ft. Extra Heavy Duty crusher, which is currently used in the majority of the mining operations throughout the world. The 10 Ft. crusher, when compared to the 7 Ft. Extra Heavy Duty Crusher, is approximately 1-1/2 times larger in physical dimensions; three times heavier; will accept a maximum feed size which is approximately twice as large; and will crush at approximately 2-1/4 times the rate of the 7 Ft. machine at identical closed side settings. It will be the largest cone crusher built in the world. At the present time, Rexnord's Nordberg Machinery Group has accepted an order for two 10 Ft. Standard cone crushers to be delivered to an iron ore mine in South Africa in early 1975.

Jan 1, 1973

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By P. Randall, J. Ickes, S. Chattopadhyay

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (Eh) conditions were performed. Since iron (Fe) is present in large quantities in mining wastes, the effect of Fe on leaching of Hg was also determined. Results show that the Hg concentration increased as the pH of the suspension increased until a pH value of 10.65. Thereafter, the Hg concentration decreased sharply. The Hg concentration, in presence of Fe decreased significantly (1/10thto 1/100th). Kinetics results show a relatively slow rate of leaching in presence of ferric ions. The results obtained from the present study are being used to predict the fate and stability of Hg present in the environment, and will therefore, be useful in dictating the nature and suitability of any remediation treatment.

Jan 1, 2003

By Nathaniel Herz, R. J. Adamson, C. M. Romanowitz, Frank W. Jr. McQuiston, C. D. Hoyt, Robert S. Shoemaker, P. H. O’Neil

1. INTRODUCTION In this section, precious metals are defined as gold, silver, and the platinum group metals comprised of platinum, palladium, iridium, osmium, and rhodium. If the first three years of the 1970's are the criteria, gold, silver, and platinum seem destined for a bright future. Gold advanced in price from the historic figure of $35 established in 1934 to over $100 per oz (1973). For the five years 1966 to 1970, silver consumption exceeded production by about 50%. The silver price appears to be definitely on the uptrend, and a price of over $3 per oz seems probable. On this basis (at 1964 costs) the United States has an estimated 5 billion oz of unmined silver. The fresh burst of interest in platinum with a surge of renewed price strength (end of 1972) is due to the activity in the automobile emission control area, where platinum re¬mains the front runner in the catalyst area. Some international financial experts believe that governments will not rush into reform of the monetary system, and "Special Drawing Rights" (SDR's) will gain increased standing as international mone¬tary reserve assets. Gold will continue to be reviewed as the ultimate store of value and will remain the global monetary base. Devaluation of the U.S. dollar caused by imbalance of import payments over ex¬ports is the basic reason that the price of gold will likely remain above the $90 per oz figure for the balance of the 1970's. Gold and silver usually occur intimately associated, and recovery methods are often closely related; however, they were assigned sepa¬rate chapters, because the major production of each metal is from ore deposits classified as either gold or silver. For example, the gold ore occurrences in South Africa, the world's leading gold producer, have a ratio of gold to silver of approximately 10 to 1. The ores at the Homestake Mine, Lead, S.D., the largest U.S. gold producer, are predominantly gold with a ratio to silver of approximately 5 to 1. Silver in each example is a byproduct. By this same classification, the largest U.S. silver producers are the silver ores of the Sunshine, Galena, and Lucky Friday mines in the Coeur d'Alene district, Idaho. However, the largest single-mine silver producer in the Free World is the Kidd Creek Mine at Timmins, Ont., where the occurrence is with sulfides of copper, lead, and zinc. Thus, the major gold production of the world is derived from those ores classified as gold ores; whereas, less than one-half of the silver production is from silver ores, and only a small percentage of the silver production is from gold ores. 2. GOLD Gold, the noblest of metals, has been mined for thousands of years. Its chemical symbol, Au, is derived from the Latin "aurum," meaning "shining dawn." A precious substance because it is one of the rarest metals, it has unique physical properties: it does not tarnish; it exceeds all other metals or alloys in malleability and ductility; it is a good conductor of electricity and is one of the most nonreactive metals. Its greatest strength is its indestructibility. It is the only metal mined at depths exceeding 10,000 ft. Since the early 1800s, its chief role has been as a medium of exchange, providing the basis for interna¬tional trade. In the past 15 years, however, gold has emerged as a useful industrial commodity. This role has been fortified by the estab¬lishment of a two-tier pricing system which maintains monetary gold prices at an established U.S. Government price, with industrial gold being priced higher by the free-market system. Occurrences and Production Native gold furnishes most of the world's production, since gold forms stable natural compounds with few other elements. Neverthe¬less, the metal is widespread with traces of it found in seawater and in the ashes of plants and animal material. Next to the native metal, the tellurides have been the most important gold-bearing minerals; these include calaverite, krennerite, slyvanite, hessite, and nagyagite. Native gold is invariably alloyed with more or less silver, but it is exceptional to find any other metal in the alloy. It is found in veins associated with quartz, calcite, alunite, other gangue minerals, and with various sulfides. Sulfide minerals in order of frequent associa¬tion are: pyrite, galena, chalcopyrite, sphalerite, arsenopyrite, tetrahe¬drite, and pyrrhotite. Small amounts of metallic gold are commonly disseminated through such sulfides. When considerable amounts of silver occur in gold, the mineral electrum is formed. In a few deposits, gold and mercury form natural amalgam. Native mercury is formed by weathering from cinnabar and other mercury minerals. Among the minerals sometimes mistaken for gold, pyrite, marcasite, and especially chalcopyrite may be men¬tioned. The flakes of biotite and other micas, especially when partially oxidized, also may imitate it closely. World gold reserves never have been estimated carefully. Esti¬mates indicate that present world reserves approximate I billion oz, of which about 60% occurs in South Africa and 20% in the USSR. World gold output is dominated by South Africa which produces two-thirds of the world's production from reserves that are adequate to maintain existing output levels. South African gold output comes from approximately 50 large underground operations that mine and mill 70 to 80 million tons of ore annually to recover 30 to 32 million oz of gold. The USSR is the second largest gold producer, followed by Canada and the United States (see Table 1). Gold production in the United States and Canada rose to high levels in the 1930's, following the increase in price from $20.67 to $35 per oz and with an abundance of good labor due to depression in other industries. Production of over 10 million oz in 1940 was behind only that of South Africa. World War II caused a precipitous drop in gold output due to the imposition of War Production Board Limitation Order L-208 issued in October 1942, which caused over 9,000 gold mines in the United States to shut down, most of which never reopened. The U.S. Treasury, which suspended purchases of newly mined gold in 1968, had been the sole buyer of U.S. produced gold since 1934. This created the two-tier pricing system, and in March 1972 the President signed into law a bill authorizing a $3 increase in the official price of gold to $38 per oz. In February 1973 the President ordered a second devaluation of the dollar, amounting to about 10% which raised the official price to $42.22 per oz. The erratic development of the gold market, which has seen the

Jan 1, 1985

By David G. Kidd

The principles of Ore Sorting in general and photometric sorting in particular are discussed with detailed reference to the Model 16 machine. The operating principles and design of the Model 16 are discussed and a case study presented to demonstrate the use of sorters to process an industrial mineral. In addition, an economic study is presented, to highlight the benefits of ore sorting, by evaluating the increased revenue that can be achieved using an ore sorter to process a particular ore body.

Jan 1, 1983

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By W. A. Haley

The use of diesel engines in underground hard-rock mines dates back to the late 1940s. For the first several years, they were used only occasionally, being limited to a few metal mines that experimented with crawler¬mounted front-end loaders, tractor-trailer hauling units, a few tractors for drill-compressor mounts, and utility cleanup machines. By the mid-1950s, track loaders had become commonplace in limestone mines and uranium mines on the Colorado Plateau in the United States, as well as in Canada. Use of crawler-mounted tractors as drill and compressor mounts also increased. By the end of the 1950s, rubber-tired loaders and some haulers began to replace the track-type machines and rail-mounted cars that had been in use. About 1960, the rubber-tired machines brought about a new era of underground mining mobility and flexibility, centered on a method commonly known as "trackless mining." Ultimately, many of the underground rail-type systems for loading and hauling were replaced by the trackless mining technique. ECONOMIC CONSIDERATIONS The size and nature of mineral deposits, plus ground control techniques, historically had dictated small open¬ings to the surface from many underground mines. The small mine openings led to the development of special rubber-tired loaders and haulers designed specifically for access through the small openings. However, some mines, particularly those in massive mineral deposits, are able to excavate and maintain very large openings, and some use modified room-and-pillar systems. With the large mine openings, the use of larger, more produc¬tive equipment such as that commonly found in surface mining becomes economical. In fact, productivity gen¬erally increases at a more pronounced rate than machine size increases because many of the larger machines were designed for heavy-duty shot-rock applications in surface mines and construction sites where the handling of blasted rock is common. Table 1 can be used as a very Table 1. General Productivity Comparison for Conventional Machines In Underground Use (Shot-Rock Conditions) 2.3 m3 (3 cu yd) 4.6 m3 (6 cu yd) Loader Loader Expected Surface 230 t/h 540 t/h Production (250 stph) (600 stph) Expected Underground 90 t/h 270 t/h Production (100 stph) (300 stph) Expected Total Efficiency: Surface 40%-60% 50%75% Underground 25%.-40% 30%50% Expected Useful Machine 8000 hr 12,000 hr Life Before Replacement general comparison of the production and efficiency between small and large machines. Combining greater productivity often inherent in larger machines, with reduced downtime resulting from using fully developed machines with fast parts and service backup, some mine operators have been able to reduce material handling costs appreciably while reduc¬ing manpower requirements for operators and main¬tenance men. Large mine openings increase the amount of rock that must be handled in the development work, and they sometimes increase the dilution in stopes or rooms, de¬pending upon the dimensions of the ore zone. Providing adequate space for the unrestricted operation of large surface mining machines could, therefore, lead to more waste segregation and handling costs. It could also cause greater ore dilution that would result in a lower grade of ore being delivered to the processing plant. The tradeoffs between opposing cost factors must be reconciled and balanced to achieve the best overall cost of the crude ore, concentrates, or product. EQUIPMENT MODIFICATIONS Loaders and haulers designed for surface mining are seldom used underground in their standard con¬figurations without some modifications. If done, the modifications generally are made by the equipment dealer and/or the user, and the modifications usually include one or more of the following items: 1) The exhaust stack is lowered, and its direction is changed. Usually, it is repositioned horizontally to the rear, or it is fed into the engine fan to diffuse the exhaust gases. 2) The operator's position is lowered by either lowering the seat or changing the seat to a side mount. 3) The operator controls are adjusted to fit the new operator position. 4) Other components, such as the radiator and loader tower, are lowered. 5) Special bumper guards are mounted at the base of the radiator area. 6) An exhaust conditioner is mounted and con¬nected, using either a catalytic or a water-type condi¬tioner, or both. This usually is controlled by the safety and health regulatory authority having jurisdiction. 7) The positions of other components are rearranged

Jan 1, 1982