Search Documents

By Pramod C. Thakur

During the past ten years, the US coal industry has experimented with various ways to extract methane from coal seams. Drilling long horizontal boreholes in solid coal from mine workings and vertical gob degas boreholes are becoming standard techniques for methane recovery from coal seams. Prime motivations for such work have always been safety and productivity in mines, but the commercial value of gas so produced is encouraging utilization. The paper reviews various ways to produce methane from coal seams and discusses some utilization projects extant in the industry.

Jan 1, 1984

By Donald W. Gentry

The evaluation of industrial minerals deposits for investment decision making follows the same basic principles that apply to metallic deposits. For example, the quantity and quality of the mineral occurrence is assessed, engineering/economic feasibility studies are performed for various production scenarios, project evaluation criteria are calculated for each alternative, and finally, an investment decision is made. A more specific evaluation-related example of commonality between metallic and nonmetallic deposit assessment relates to the various parameters which impact project feasibility studies. There exists a suite of pertinent factors which must be considered, studied, and analyzed when evaluating any mining property. Table 1 is an outline of some, but certainly not all, of the various factors which should be considered when preparing feasibility studies on mining properties. Most analysts agree that all the factors listed in Table 1 should be assessed to some degree in at least one of the feasibility studies prepared during the property's evaluation period.

Jan 1, 1984

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

And a new generation of safety culture experts are telling mining companies how to use it: It is a situation that is still too common in the mining industry: the latest personal protective gear is in place. The safety rules are known and followed. And then, in a moment of inattention or carelessness, a mistake is made and someone gets hurt or killed. Common wisdom claims that such accidents are impossible to eliminate entirely. Mining is dangerous, and some miners will always be hurt and killed. An increasing number of mine safety experts, however, reject the common wisdom. A year with zero mining deaths is possible, they say; with the use of one of the newest weapons to the mining industry in the safety war: the concept of safety culture. Safety culture refers to the set of attitudes, beliefs, perceptions and values that influence safety in the work environment. It is also sometimes called the way an organization behaves when no one is watching. Robert Peters, of the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH), describes safety culture this way: ?It?s what?s believed on a day-to-day basis. For example, if a miner sees a workplace hazard and he truly believes that his boss wants him to identify the hazard and bring it to the company?s attention, that would be an example of a positive safety culture.?

Jun 1, 2010

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By D. Kump

The Bullfrog Mine is an underground gold mine that uses the underhand-cut-and-fill mining method. The portal was established on June 18, 1991. Mining is expected to be completed by the summer of 1999. This paper starts by discussing what it took to get from nothing to 2000 tons-per-day backfill, and ends with a hindsight commentary on things that did and did not help.

Jan 1, 1999

Recent expansion programs have made the Yunkang underground coal mine the number one producer in Shenxi Province. The mine is the newest in the Datong Coal Administration, currently rated at around 3 Mt/a of coal. Located in the Wa Chushi mountain range about 23 km north of the city of Datong, the mine has undergone a series of expansion phases since startup in 1973. Initial design capacity was 1.5 Mt/a and ultimately, production will be brought to an estimated 7.0 Mt/a by 1985, according to mine superintendent Li Jia-zhi. How Coal Occurs The coal, Jurassic in age, occurs in three economically identifiable seams designated No. 2, 3, and 7. Seams are 100-250 m below the surface. Reserves from this economic zone were not quantified, but Superintendent Li indicated that there was enough mapped out to sustain the expanded production rate for over 20 years. Below the Jurassic coal is another possible economic zone, a Permocarboniferous coal lying 400-600 m below the surface. Little development drilling has been conducted to ascertain its potential. The Jurassic beds are relatively flat and coal quality is reportedly one of the best in China. Heat content of the coal runs around 33.5 MJ/kg and the ash content is less than 10%. In some areas, it is less than 7%. Coal preparation is simple and involves a washing and screening separation into four principal size fractions. Washed coal is stored in one of six storage silos, each with 4000-t capacity. Mining the No. 2 Seam Since startup, primary production has been derived from the No. 2 seam. The coal is relatively hard and is topped by a hard cement-like conglomerate. These factors, coupled with an average thickness between 4 to 6 m, precluded the use of conventional longwall techniques, according to mine engineers. The solution was development of a room-and-pillar tech-

Jan 3, 1980

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By G. T. Lineberry

A systematic, comprehensive, balanced approach is presented for underground coal mine design, capable of being standardized and generalized. This approach epitomizes professionalism and must preceed the physical product. Design involves a varied senior staff and requires extensive selective input data. Engineering follows a total systems approach, operating in and for a constricting geologic setting, heavily constrained for safety, health, and environmental protection. It must also anticipate execution and operation. Engineering prominence and momentum are maintained, with sub-optimizations balanced by judgments--the "art and science" of engineering. The flow-chart starts with organized input data: Company Capabilities, Property Description, Geologic Analysis and Reserve Analysis. Engineering combines Ground Control with Excavating and Bulk Handling to map feasible Mining Methods, the crucial Milestone Diagram. Layout and Sequencing follow, with numerous alternatives examined. Scheduling is performed on the best designs, using predicted advance (performance) rates. Active and mined-out areas are isolated into time-related parcels, or increments, for the mine life. Bulk Handling, Life Support (especially ventilation and drainage), and Normal Support systems occupy each parcel. Regulations are then checked. Management concerns are covered, and an Economic Analysis is performed for profitability. This and the design represent an Initial Tentative Solution. Continued iterations produce multiple and improved choices.

Jan 1, 1987

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

During dusk, nighttime and dawn operations, effective illumination is a crucial component of safety for getting on/off mobile surface mining equipment and for preshift inspections. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers examined whether illuminance levels could be improved for ingress/egress systems and preshift walkaround inspections of equipment using light-emitting diode (LED) area luminaires. Illumination and glare were key metrics evaluated. Although headlamps provided adequate illumination, LED area luminaires illuminated a much broader area compared to the narrow spot lighting of the headlamp. Hence, the use of additional area luminaires can increase slip-trip-fall (STF) hazard awareness and detection. Furthermore, a commercially available luminaire demonstrated better results than a custom LED luminaire relative to discomfort and disability glare.

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969