Search Documents

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Richard J. Lewandowski

Corrosion and product contamination have been difficult problems for extractive metallurgy industries in the U.S. because of the highly active chemicals used. During the past twelve years, other industries, particularly the chemical and paper segments, began to combat this problem with some degree of success using newer materials of construction, including reinforced plastics. These materials are made by combining a corrosion resistant thermosetting resin with a glass fiber reinforcing material and are used to con¬struct hoods, stacks, blowers, tanks, towers, pipe, and equipment of the most complex configurations. For service in contact with aggressive chemicals, the equipment is most often fabricated with the bisphenol-A fumarate polyester resins because of their resistance to corrosive attack. Data from both laboratory work and case histories of field applications are presented-for many common chemicals found in extractive processes. Information is also presented concerning design standards and recommended construction procedures

Jan 1, 1970

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Richard H. Johnson

White Pine Copper Company began operating a plant designed to recover copper matte particles from its discarded reverberatory furnace slags in April, 1972. Seasonal operation, generally the months of April through November, continued through October, 1974, shutting down due to feed exhaustion. White Pine reverberatory furnace slags contained economically recoverable amounts of copper for a variety of reasons. Among them: 1. White Pine concentrates yield extremely high matte grades (65+% Cu) and viscous slags. The viscous slags hinder matte settling causing matte "prill" entrapment in the slag 2. White Pine's total refined copper output is accomplished through fire refining requiring special techniques for impurity removal, especially small amounts of nickel introduced from purchased pyrite and chalcopyrite fluxes. These special techniques result in high-copper slags, refractory to smelting, being reintroduced into the reverberatory furnace. 3. Furnace bottom build-ups resulting in mechanical matte entrapment through the formation of "dams" hindering matte flow. 4. Occasional concentrate fluxing and furnace atmosphere control problems.

Jan 1, 1975

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By Rebecca Mae Summer

Large scale surface mining has a major impact on land use. Without reclamation, abandoned mining sites are usually less productive than before mining. With increasing and completetive land use demands in the United States, it becomes increasingly evident that multiple land use should be considered for all areas that will be mined, with special emphasis on coal, sand, gravel, and stone. The mining of these commodities affects the largest land areas and the latter two are commonly mined near population centers where high land-use pressures justify serious consideration of multiple use. Typically, sequential use will mean restoration of the mined land or at least transformation of the land into a useable state. Determination of land reclamation capability is a viable approach to planning reclamation of surface mined land. The natural resource base--geology, soil, and water--controls the type and intensity of land-use practices which can be sustained following mining. Evaluating physical limitations can eliminate consideration of uses which would severely impair the environment or which are impractical. This approach provides for an environmentally and economically sound land use at very little cost. In addition, it can save or make money for the mining company and landowner. Sand and gravel is an especially significant resource because it is mined throughout the entire country and commonly extracted near cities. Increasing urban growth and industrial activity require increased supplies of sand and gravel. This translates into expanded surface mining and an increase of disrupted land. Oftentimes this land is within an urban area and has potential for real estate or water-based activities. Therefore, if reclamation is planned and carried out concurrently with mining, it is definitely feasible and

Jan 1, 1977

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By Innocent John Arinze, Chidubem Okwudiri Emedo

This contribution presents the first multi-scale geophysical investigation conducted in the Abakaliki and Obubra mining districts (AOMD), southeastern Nigeria, for the exploration of shallowly emplaced (< 50 m) massive sulfide and barite mineral deposits. Raw airborne magnetic data covering the AOMD was acquired and subjected to diverse enhancement routines to facilitate the identification of areas of subtle magnetic anomalies for subsequent ground truthing. The mineralization is mainly made up of galena, sphalerite, and barite. The contrasting physical properties between these minerals and their host rocks make resistivity, induced polarization (IP), spontaneous potential (SP), and magnetic methods ideal to study and delineate the mineralization and possibly locate the ore bodies. Wenner DC resistivity and IP data acquired along the same parallel traverses are inverted using Res2dinv to produce 2D tomography models of resistivity and chargeability. The resistivity and IP models were successful in delineating zones of sulfide and barite mineralization. The ground SP data collected along the same traverses as the resistivity and IP data were interpreted as line graphs. The 1D SP models show a number of central negative anomalies that could be related to sulfide mineralization. These anomalies show fair-to-good spatial continuity and are in close agreement with the result obtained in the resistivity and chargeability model. This study suggests the presence of exploitable mineral deposits in the AOMD and demonstrates the superior interpretative ability of combined geophysical methods over a single geophysical approach.

Oct 20, 2020

By Clayton Williams, Dale M. Hata, Glenn M. Boyce

The Upper Llagas Creek Flood Protection Project in Northern California encompasses portions of the communities of Morgan Hill and Gilroy, and unincorporated areas of Santa Clara County. The project provides for flood protection improvements along Llagas Creek and two of its tributaries, West Little Llagas Creek and East Little Llagas Creek. Llagas Creek is one of the tributaries of the Pajaro River and drains a watershed of approximately 104 square miles. The river system has a history of flooding the watershed communities, and the project’s goal is to provide 100-year flood protection by creating a bypass infrastructure, including channels, cut-and-cover culverts, and a tunnel. The project has been divided into several phases. This paper describes Phase 2A, which consists of approximately 2,150 linear feet of lined horseshoe-shaped bypass tunnel measuring 14 feet wide by 12 feet high. The bypass tunnel was sequentially excavated using a combination of roadheader and controlled blasting through colluvium and weathered to fresh greenstone. The tunnel was mined near residences, requiring strict noise and vibration controls. Phase 2A also includes the construction of twin bypass concrete culverts, portal shoring, and dewatering systems. It features the use of a Design Review Board and partnering for project delivery. This case study discusses the bypass tunnel design, progress of tunnel construction, plans to complete the work, construction risks, and the software and procedural tools being used to manage the project, including ProjectWise construction management software.

Jun 13, 2023

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By U. K. Custred

Who We Are Farmland Hydro (FHLP) is a Limited Partnership formed by Farmland Industries, the largest U.S. farmers’ cooperative, located in Kansas City, MO, and Norsk Hydro, a large Norwegian company engaged in fertilizer, petroleum and the specialty metals industry. Both of our parent companies have a long history of commitment to the fertilizer industry. This year, Farmland Industry celebrates its 71st year in the business, and Norsk Hydro celebrates its 100th operating year! We employ approximately 300 associates in Central Florida. What We Do Farmland has been active in Hardee County, FL since the 1970’s as a large landowner and citrus grower. We plan to expand this activity into phosphate rock mining. The phosphate rock produced here will be shipped to our nearby chemical fertilizer complex in Polk County, where we produce quality phosphate products - liquid and granular fertilizers. Of the phosphate rock mined, 90% is used to make fertilizer. Other uses include animal feed, vitamins, medicine, light bulbs, soft drinks, film, flame resistant fabric, optical glass, toothpaste, bone china and other consumer products.

Jan 1, 2000

By C. Patrick

Longwall face-to-face equipment transfers or moves are, for many companies, the largest single source of non-productive time in a longwall mining system. Detailed planning and resourceful thinking are paramount for economical, safe, and timely longwall moves. New equipment and innovative techniques are frequently tested in order to reduce overall move time. Determining the cost effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed in order to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several innovative ideas.

Jan 1, 1994

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today&apos;s answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world&apos;s direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Cesar A. Busnardo

The carbonatite orebody in Jacupiranga is situated some 230km (140-mi) southwest of Sao Paulo and is mined by Serrana S/A de Mineragao, producing an apatite concentrate for fertilizer production and a calcite tailing for cement manufacture (see Figure 1). The orebody (Table 1) is mined by open pit and the total production is 4.5 million mt/year of carbonatite ore with a further 2.2 million mt/year of overburden. The carbonatite low-grade ore (Table 2) is fed to the concentration plant at 460 mt/h , comprising of four parallel lines of grinding, by rod mills 2.7m x 4.5m (9 x 15-ft), operating in closed circuit with hydrocyclones. The grinding circuit product is deslimed in four stages using hydrocyclones and the deslimed product is conditioned with corn starch and subsequently floated, using fatty acids as collector to, recover the apatite.

Jan 1, 1985