Search Documents

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Ren Xiangwen, Shi Xuefa, Shao Mingjuan, Ye Jun, Yang Yaomin, Li Bing

"The Mid-Atlantic Ridge (MAR), one of the archetypes of slow spreading ocean ridges, extends from the Arctic Mid-Ocean Ridge southward to the Bouvet triple junction making up a significant proportion (~ 40%) of the global oceanic ridge system. During the past few decades, many hydrothermal fields like TAG, Logatchev, Ashasze were discovered along the northern part of the MAR, whereas the southern part, which makes up one third of the ridge (6000km), shows little documentation of hydrothermal mineralization, except for three sites: Site 4°48! the Nibelungen Field, and Lilliput. During March to May 2011, following discovery of three new hydrothermal fields during the 2nd Leg of COMRA's 22 Cruise of the R/V DayangYihao, the 3rd and 4th Legs found another two high temperature hydrothermal fields (SMAR15°S, SMAR26°S), one low temperature field, and several fields with strong turbidity and temperature anomalies in the water column. In this study, we present a preliminarily study of the mineralogy and isotopic geochemistry of the sulfides from SMAR 15°S and SMAR26°S.SMAR 15°S is situated in a SE-NW offset depression of an axial neovolcanic ridge in the median valley, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten-meter tall venting chimneys, hydrothermal mounds, as well as a large amount of hydrothermal vent shrimp were also observed and recorded by ROV and deep-tow camera surveys. The samples collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. Based on the major metal and the mineral assemblages, three types of sulfides have been identified: 1) Zn-Fe rich sulfides with abundant wurtzite and pyrite zoned fragments, 2) Cu-Fe rich sulfides with much isocubanite and pyrite assemblage, 3) Fe-rich sulfide with massive pyrite fragments. These indicate that this field has undergone at least three phases of mineralization during the venting history."

Sep 1, 2014

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

During the last 20 years, more than 80 km (50 miles) of tunnels have been constructed in the Los Angeles, CA area. Recent projects include The East Central Interceptor Sewer (ECIS), completed in 2004. It spans more than 18 km (11 miles). The Northeast Interceptor Sewer (NEIS), completed in 2005, spans 11 km (7 miles). And the 2-km (1.3-mile) Metropolitan Transportation Authority?s Gold Line Eastside Extension (MCGLEE) was completed in 2006. All of the tunnel routes lay beneath heavily populated urban environments so minimizing ground surface settlement was critical to the success of the projects. Previous tunneling efforts in the Los Angeles area using open shield methods resulted in significant settlement that damaged roads, utilities, buildings and other structures. Earth pressure balance (EPB), or slurry machines, were specified for these projects to reduce subsidence risk. The contractors chose EPB tunnel boring machines (TBM) for the work. The closed and pressured face of the EPB TBM reduces loss of ground at the tunnel face and, when the machines are used in combination with gasketed pre-cast tunnel liners and backfill grout behind the installed segments, losses from over-cut of the excavated surface are also reduced.

Jan 1, 2008

By K. Wangerud, B. S. Caruso

A water balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site, South Dakota, to evaluate risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for analysis of precipitation based on historic records, and for probabilistic estimation of annual and monthly runoff from primary disturbed/mining activity areas that currently requires, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/Excel add-in “@Risk” was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation, and groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2002

One of the biggest challenges for the mining industry is, quite literally, how to the keep the equipment rolling. There is a limited amount of companies that manufacture the 4.2-m- (14-ft-) tall, 5,670-kg (12,500-lb-) tires needed for the haul trucks that are approaching the 362 t (400 st) pay-load class, such as Terex?s MT6300-AC and Caterpillar?s 797F. And, while these might be the most impressive tires, they are not the only ones that are in short supply. The shortage of tires has affected just about every kind of machine, and the demand for those tires has been extremely high for more than five years with no end to the shortage in site. American Tire Corp. (www.americantire.us) is one of the companies working to supply tires to the mining industry. It announced that the demand for its 1.6-m (63-in.) tires that have a zero failure history globally is great and that the company signed contracts worth more than $500 million at MinExpo. A relatively new player in the field of large tires for mining equipment is Titan Tire Corp., (www.titan-intl.com), a subsidiary of Titan International Inc. It shipped its first 1.6 m (63 in.) off-the-

Jan 1, 2008

By Hugh R. Rhys

The question of the desirability of recovering cullet from MSW in order to recycle it into the manufacturing of glass containers remains a controversial one. The main factors appear to be: 1. The position of the Glass Container Manufacturers Institute (GCMI), as the trade association for most container manufacturers, is that post-consumer cullet is a vital source of raw material. Present requirements are for: a) Flint cullet b) Non-flint cullet of known mix proportions c) Mixed unsorted cullet of known mix propertions c) Mixed or non-flint cullet of unknown mix proportions. A market balance for these products exists, and this might somewhat limit the outlets for (b), (c) and (d), or severely limit the outlet for (d) alone. 2. The color specifications are rather strict. With cullet admixtures of 20% of the melt or more, and the use of decolorisers in a flint furnace discouraged because their action is reducing in a process which requires an oxidising environment, color contamination in a flint furnace is serious.. For amber and green furnaces (reducing) it is less serious, but in order that the quantity of decolorisers may be controlled, the color balance (as a measure of the Fe and Cr content) of the admixtured cullet should be known. 3. Why not simply color analyze, either by a continuous on-stream or off-stream: photo-electronic analysis, or by systematic batch sampling (with some kind off electronic surveillance of the mainstream) and just send mixed, color measured cullet to only amber and green furnaces? The flint would-be simply included in the mix. This is probably technically feasible, but is subject to the market limitations noted in point1.

Jan 1, 1975

By A. Davis, C. Webb, J. Sorensen

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM). The mine produced lead and zinc during the first half of the 1900s. Because of acidic drainage and elevated levels of metals in tailings and waste rock, the site was evaluated in 1998 and 1999. After evaluation, the mine was remediated during 1999-2001 by the BLM. Since remediation, values of pH in water samples have been nearly neutral and specific conductance values have been much lower than before remediation. The Grizzly Gulch forest fire of July, 2002, consumed much of the Belle Eldridge site and resulted in greater than normal erosion and sediment flushing during the months following the wildfire. Had the site not been remediated and the tailings emplaced within a capped repository, generation of acidity and off-site migration of heavy metals within sediments could have been severe at downstream locations.

Jan 1, 2007